Philips 46pfl9704 User Manual

							5.4.6   DecoderUse a scart cable to connect a decoder which decodes
analogue antenna channels. Use the EXT1 or EXT2
connectors at the back of the TV.
You have to assign the TV channel as a channel to be
decoded. Then assign the connection where the decoder is
connected.
Close this user manual and press h > Setup > Installation
> Decoder. Select Channel to set the channel that you want
to decode. Select Status to set the connector you use for
the decoder.
 
						

							5.5.1      EasyLink1/2If a device is equipped with the HDMI-CEC standard, the
device and the TV can work together.
Connect the TV to the device using an HDMI cable. The
TV comes with EasyLink set to On. To switch EasyLink off,
press h > Setup > Installation > Preferences > EasyLink.
With EasyLink, the following functions are available:
• One touch play
Insert a disc and press Play on the device. The TV switches
on from standby mode and shows the disc programme
automatically.
• System standby
Press O on the TV remote control for 2 seconds to switch
the connected devices into standby mode.
...
 
						

							5.5.1      EasyLink2/2• System audio control
If you connect an audio system, you can listen to the audio
from the TV through the audio system. The TV speakers are
muted automatically.
The TV comes with the speakers set to EasyLink
(Automatic). To switch the TV speakers off or permanently
on, press h > Setup > Sound > TV speakers.
Make sure that all HDMI-CEC settings are properly set up
on the device . EasyLink might not work with devices from
other brands.
Naming of HDMI-CEC on other brands
The HDMI-CEC functionality has different names with
different brands. Some examples of name are: Anynet,
Aquos Link, Bravia Theatre Sync, Kuro Link, Simplink, Viera
Link, ...
Not all brands are fully compatible with EasyLink.
 
						

							5.5.2   EasyLink Remote ControlFirst read Connections > EasyLink, before you go on with
EasyLink Remote control.
With EasyLink Remote control, the TV remote control
commands are sent directly to the device you are watching
on TV. There is no need to select the device on the remote
control first.
Caution> This is an advanced setting. Verify if all devices
are suited for this setting. Unsuited devices will not
respond. Try out this function first, before you switch on
EasyLink Remote control permanently.
To switch EasyLink Remote control on, press h > Setup >
Installation > Preferences > EasyLink Remote control.
Except for the Home h key, all remote control commands
will try to operate the device. Some commands might not
work with the device.
To switch back to TV control, press h and select Watch TV
To control another device, press h and select the other
device.
 
						

							5.6.1      Conditional  Access  Module  (CAM)1/2Scrambled digital TV channels can be decoded with a
Conditional Access Module (CAM). Digital TV service
operators provide the CAM when you subscribe to their
services. Contact a digital TV service operator for more
information and terms & conditions.
Insert a CAM
Switch off the TV before inserting a CAM.
Look on the CAM for the correct method of insertion.
Incorrect insertion can damage the CAM and the TV.
Look for the common interface slot on the side of the TV.
Gently insert the CAM as far as it will go and leave it in the
slot permanently.
It can take a few minutes before the CAM is activated.
Removing the CAM will deactivate the service on TV.
...
 
						

							5.6.1      Conditional  Access  Module2/2Watching a CAM service
If a CAM is inserted and subscription fees have been paid,
the TV shows the programme from the digital TV service
provider. The applications, their function, the content and
the onscreen messages all come from the CAM service.
CAM settings
To set passwords or PIN codes for the CAM service, press
h > Setup > Features > Common Interface. Select the CAM
provider and press OK.
 
						

							5.6.2   Common Interface Plus CI+This TV can handle the CI+ conditional access.
CI+ allows service providers to offer premium HD digital
programmes with a high level of copy protection.
To insert a CI+ CAM, read the chapter CAM - Conditional
Access Module.
 
						

							5.7.1   Wireless network connectionTo set up the wireless network connection, read all
chapters in Setup > Network.
 
						

							5.7.2   Wired network connectionTo set up the wired network connection, read all chapters
in Setup > Network.
Connect the router to the TV using a network cable
and switch on the router before you start the network
installation.
 
						

							6.1   Contact informationWarning
If your TV breaks down, NEVER try to repair the TV yourself.
If the advice and suggestions in Troubleshooting do not
help resolve the problem, try switching the TV off and back
on again.
Contact information — Consumer Care
If the TV problem is not solved you can call the Philips
Consumer Care hotline in your country. Find the telephone
number on the printed documentation that came with the
TV.
Or consult our website www.philips.com/support
TV model number and serial number
Find these numbers on the packaging label or on the type
label on the back or bottom of the TV.