Philips 42pfl9803 User Manual

							Use more of your TV
†The update process star ts automatically. Please
wait.
The update is finished when the message
‘Operation successful ’appears on the screen.
º Remove the USB memor y device from the TV.
◊ Press  Bon the remote control.
Do not press more than once and do not use
the  Power Bswitch on the TV.
‹ The TV switches off. The screen stays black for
about 10 seconds. Please, wait. ≈
The TV switches back on again. The update is
done.
5.13.2 Software update by digital broadcast (DVB-T)
Y our TV might receive new software from the
digital broadcast system automatically.
If you receive an update message on screen it is
strongly advised to update the software
immediately - select  Now.
If you want to be reminded later on, select  Later.
Select  Cancel to quit the update (not
recommended). If you cancelled the update you can
still update yourself from the TV menu > Setup >
Software update > Local updates.
29
ENGLISH
BSU
Operation Successful! Re
Prg
BSU
B
S
U
TELETEXT SUBTITLE
UNIVERSAL MODE
SOURCE
DEMO
2705.3 EN  20-05-2008  10:03  Pagina 29
 
						

							Channel installation
6Channel installation
The first time you turned on your TV 
•you have selected the language of the TV menus
and the countr y where you are located
• all the available TV Channels have been installed.
This chapter provides instructions on how to
reinstall channels as well as other useful channel
installation features.
r Note :
Re-installation will modify the All channels list and
new added channels will not be added to any
favourite list.
6.1 Automatic installation
This section describes how to search for and store
all available channels automatically.
Step 1: Menu language  
Sets the language of the TV menus. Go to a next
step if your language settings are correct.
‡ Press  Menu  Ïon the remote control and
select Setup > Installation >  Languagesand
press  πto enter  Menu language .
® Press  oor œ to select your language.
Ò Press 
OKto confirm.
† Press  pto return to the Installation menu.
The Languages menu also offers the following
language settings when digital channels are installed
and broadcasted.
• Preferred audio language
Select one of the available audio languages as
primar y preferred and secondar y preferred
language.
• Preferred subtitle languages
Select one of the available subtitle languages as
primar y preferred and secondar y preferred
language. See section  5.10 Subtitles. •
Preferred teletext languages
Select one of the available teletext languages as
primar y referred and secondar y preferred
language.
• Hearing impaired
Select  Onto display the hearing impaired subtitle
ve rsion of your preferred audio or subtitle
language when available.
• Visually impaired (UK only)
Select to hear the additional commentar y audio
(if available) in your selected audio language
through the loudspeakers of your TV or through
the headphones or through both
r Note :
If both Visually impaired and Hearing impaired are
enabled, the Visually impaired language will have
priority for audio, the Hearing impaired for subtitles.
• Preferred audio format
Select your preferred and available audio format
to achieve the best sound reproduction.
Select  Advanced for the best sound reproduction
if a Home theatre system is connected to your
TV. Select  Standardin all other cases.
Step 2: Select your country  
Select the countr y where you are located.
The TV will install and arrange the TV channels
according to the countr y selected.
Go to a next step if your countr y selection is
correct.
‡Press  œto select  Channel installation .
® Press  πto enter the Channel installation menu.
Automatic installation is highlighted.
Ò Press  πto enter.
† Press  OK.
The Countr y list appears.
º Press  oor œ to select your countr y.
◊ Press  Next.
Channel install...Automatic install...
Start nowAutomatic install...
Installation update
Start-up message
Digital: Test recept...
Analogue: Manual...
Rearrange
InstallationLanguages
Menu language
Primary audio
Secondary subtitl..
Primary teletext
Secondary teletext
Hearing impairedgp
Visually impairedimm
Pref. audio format
Languages
Preferences
Channel install...
Connections assist.
Rename devices
Audio setup
...
30
2705.3 EN  20-05-2008  10:03  Pagina 30
 
						

							Step 3: Select Antenna or Cable 
This selection is only available when this TV is
prepared to receive DVB-C channels in your
countr y.
Select Antenna to install all digital terrestrial (DVB-
T) and analogue channels available.
Select  Cableto install all digital cable (DVB-C) and
analogue channels available.
‡ Press  oor œ to select  Antennaor Cable .
® Press  Next.
Ò If the TV asks for it, enter the Network ID you
received from your provider.
r Note
Y ou can do a Channel installation if you are both
connected to a digital antenna and a cable network.
Therefore do the installation twice. To watch the
stored Antenna channels or the stored Cable
channels, you will have to switch between Antenna
or Cable in the Channel installation > Antenna or
Cable menu.
Step 4: Install TV and radio channels
Y our TV will search for and store all available digital
and analogue TV channels and all available digital
r adio channels.
If you selected Cable in Step 3, a Settings menu is
a vailable. Leave these settings unchanged unless
y our provider supplied specific values to use for
Network frequency, Network ID or Symbol rate.
Follow the text on screen to change the settings.
Use the digit keys to enter the numbers. You can
also select to install analogue channels or not.
‡ Select  Start.
The installation may take a few minutes.
In case of Cable selection, the TV can ask to
enter the Network ID supplied by the cable
provider. Enter this ID with the digit keys.
® When the installation is done, press  Finishto
return to the Channel installation menu.
Ò Press  Menu Ï to quit the menu.
à Tip
When digital channels are found, the list of installed
channels may show some empty channel numbers.
If you want to rename, reorder or uninstall stored
channels, see section  6.3 Rearrange channels .
Step 5 Clock, time zone and daylight saving
selection 
Only available when the countr y selected suppor ts
digital broadcasts.
Go to a next step if this step is not applicable.
‡ Press  œto select  Clock.
® Press  πto enter.
Ò Press  oor œ to select  Auto clock mode .
† Press  πto enter.
Auto clock mode
Select  Automatic to instruct your TV to always get
the time correctly. Time zone and Daylight saving
correction are automatically set.
Select  Manual when Universal Time Coordinated
(UTC) is not available in your area.
Time zone/Daylight saving
When you selected Auto clock mode manually,
select your local time zone and choose between
Standard (winter) and  Daylight saving time
(summer).
InstallationClock
Auto clock mode
Ti me zone
Daylight saving
...
Connections assist.
Audio setup
Rename devices
Decoder
Man. network inst.
Clock
Factory settings
Channel installation 31
ENGLISH
2705.3 EN  20-05-2008  10:03  Pagina 31
 
						

							Channel installation
6.2Analogue: Manual installation
You can tune-in analogue TV channels channel by
channel manually with Manual installation.
6.2.1 Select the system
‡ Press  Menu  Ïand select Setup > Installation
> Channel installation >  Analogue: Manual
installation .
® Press  πto enter the Manual installation menu.
System is highlighted.
Ò Press  πto enter the System list.
† Press  oor œ to select your countr y or par t
of the world where you are now located.
º Press  pto return to the Manual installation
menu.
6.2.2 Search for and store a new channel
‡ Press  Menu  Ïand select Setup > Installation
> Channel installation > Analogue: manual
installation >  Search.
® Press  πto enter the Search menu.
Ò Press the red key to enter the frequency
yourself or press the green key to search for a
next channel.
à Tip
If you know the frequency, enter the three numbers
of the frequency with the number keys of the
remote control.
† Press  pwhen the new channel has been
f ound.
º Select  Store as new channel to store the new
channel under a new channel number.
◊ Press  πto enter.
‹ Press 
OK.
Done appears.
≈ Press  Menu  Ïto quit the channel installation
menu.
6.2.3 Fine tune a channel
Fine tune a found channel when the reception is
poor.
‡ Press  Menu  Ïand select Setup > Installation
> Channel installation > Analogue: manual
installation >  Fine tune.
® Press  πto enter the Fine tune menu.
Ò Press  oor œ to adjust the frequency
† Press  p when you finished fine tuning.
º Select  Store current channel to store the fine
tuned channel under the current channel
n umber.
◊ Press  πto enter.
‹ Press 
OK.
Done appears.
≈ Press  Menu  Ïto quit the Channel installation
menu.
6.3 Rearrange stored channels
To  rename, reorder, uninstall or reinstall stored
channels.
6.3.1 Rename a channel
Assign or change a channel name to a channel for
which a name has not yet been entered.
‡ Press  Menu  Ïand select Setup > Installation
> Channel installation >  Rearrange.
® Press  π to enter the channel list.
Ò Press  oor œ in the channel list to select the
channel you want to rename.
† Press the red key.
º Press  por π to select a character or  oor œ to
change the characters. Space, numbers and other
special characters are located between  zand  A.
◊ Press the green key or 
OKto finish.
à Tip
To  delete all characters, press the yellow key.
To  delete the highlighted characters, press the blue
key..
6.3.2 Uninstall or reinstall a channel
To  uninstall a stored channel so that it is no longer
possible to tune to.
Reinstall an earlier uninstalled channel.
‡ Press  Menu  Ïand select Setup > Installation
> Channel installation >  Rearrange.
® Press  π to enter the channel list.
Channel install...Analogue: Manual...
System
Search
Fine tune
Store as new ch...
Automatic install...
Installation update
Start-up message
Rearrange
32
2705.3 EN  20-05-2008  10:03  Pagina 32
 
						

							ÒPress oor œin the channel list to select the
channel you want to uninstall or reinstall.
†Press the green key to uninstall or reinstall the
channel.
ºPress Menu Ïto quit the menu.
6.3.3 Reorder the channels
Change the order of the stored channels.
‡Press Menu Ïand select Setup > Installation
> Channel installation > Rearrange.
®Press π to enter the channel list.
ÒPress oor œin the channel list to select the
channel you want to reorder.
†Press the yellow key to move up the highlighted
channel in your channel list.
ºPress the blue key to move down the
highlighted channel in your channel list.
◊Press Menu Ïto quit the menu.
6.4 Channel management
6.4.1 Automatic search
Once a day, at 3 AM, the TV searches for all
available TV channels automatically. Leave your TV in
standby.
Earlier found channels are updated and new
channels are stored. Channels not found by the
search anymore are removed from the channel list.
When Channel management has found or removed
channels, a message at TV star t up is shown. You
can activate or deactivate this message.
‡Press Menu Ïand select Setup > Installation
> Channel installation > Startup message.
®Select On or Off.
6.4.2 Manual search
You can install the updates at any time.
‡Press Menu Ïand select Setup > Installation
> Channel installation > Installation update.
®Press π to enter the Installation update menu.
ÒPress 
OK.
†Press the green key to star t.
The update star ts and may take a few minutes.
ºWhen the update is completed, press the red
key to return to the Channel installation menu.
◊Press Menu Ïto quit the menu.
6.5 Digital reception test
If you receive Digital TV broadcasting you can verify
the quality and signal strength of a specific channel.
‡Select a channel.
®Press Menu.
ÒSelect Setup > Installation > Channel
installation > Digital: Test reception.
†Press πto enter
ºPress 
OK.
◊Press the green key to star t the test.
Information on the quality and the signal
strength of this channel is shown.
‹Use the cursor keys to change the frequency to
improve the signal or enter a new frequency
directly with the digit keys.
≈Press the green key to store the frequency if
the signal quality and strength are good.
ÚPress the red key to return to the Channel
installation menu.
œPress Menuto quit the menu.
àTip
To achieve the best results, contact a specialised
antenna installer.
6.6 Factory settings
You might want to return to the original factor y
settings. Only picture, sound and Ambilight settings
will be reset.
‡Press Menu Ïand select Setup > Installation
> Factory settings.
®Press π to enter the Factor y settings menu.
ÒPress 
OK.
†Press Menu Ïto quit the menu.
Channel installation33
ENGLISH
2705.3 EN  20-05-2008  10:03  Pagina 33
 
						

							Connections
34
7 Connections
7.1 Connection overviewSide connectors
1Headphones
Stereo Mini jack
2 Audio L/R 
Audio L/R input to be used together with Video
or S-Video on the side of the TV.
3 Video
Video input to be used together with the 
Audio L/R on the side of the TV.
4 S-Video
S-Video input to be used together with the
Audio L/R on the side of the TV.
5 USB
USB connector.
6 HDMI Side 
HDMI input
7 Common interface
Slot for Conditional Access Modules (CAM)
Back connectors
8
EXT1, EXT2
Scar t connectors for DVD, VCR, Digital receiver,
Game console, etc.
9
EXT3
Component Video Y Pb Pr and Audio L/R
connectors for DVD, Digital receiver or Game
console, etc.
V GA and Audio L/R connectors for a PC .
10 Service UART
For ser vice only.
11
Digital Audio Out
Sound output cinch connector for a Home 
Theatre System, etc.
12
Audio Out L/R
Sound output cinch connectors for a Home
Theatre System, etc.
13 Antenna input
14 Network 
Home network connector.
15 HDMI 1, HDMI 2, HDMI 3 
HDMI input connectors for Blu-ray Disc player,
HD Digital receiver or HD Game console, etc.
16 Audio L/R In [DVI to HDMI]
Audio In L/R connectors to be used together
with a DVI to HDMI connection.
2705.3 EN  20-05-2008  10:03  Pagina 34
 
						

							7.2 About connections
7.2.1 What you need to know 
Connect your device with the highest possible
quality connection.
Look for the highest quality connection on your
device. Use that connection to your TV.
HDMI- Highest quality   ★★★★★
An HDMI connection has the best picture and
sound quality. One cable combines video and audio
signals. Use HDMI for HD ( High Definition) TV
signals. HDMI with EasyLink offers easy operating
of your connected devices when these have the
HDMI CEC standard. See section  7.2.2 EasyLink
A device connected with HDMI to the TV can only
send out audio and video signals to your TV. The
device cannot receive or record audio and video
from your TV.
HDMI cable (max. 5m)
à Tip
DVI to HDMI  – Higher quality★★★★
Use a DVI to HDMI adaptor if your device has only
a DVI connection.
Connect an Audio L/R cable to Audio In L/R (DVI
to HDMI) for sound.
Assign this Audio In to the HDMI 1, 2 or 3 where
the device is connected. See section  7.5.2 Audio
setup  (if present).
r Note
HDMI suppor ts HDCP (High-bandwidth Digital
Contents Protection). HDCP is a copy protection
signal that comes with HD content (DVD disc or
Blu-ray Disc).
YPbPr  – Higher quality ★★★★ 
Use the Component Video YPbPr connections
together with Audio Left and Right. Match the cable
colours when you connect.
YPbPr can handle HD TV signals.
Component Video Audio L/R cable
YPbPr cable - Red, White
- Red, Green, Blue
Scart  - Good quality ★★★
One cable combines video and audio signals.
Scar t connectors can handle RGB video but no HD
TV signals.
Scar t cable
S-Video  - Good quality ★★
Use an S-Video cable together with an Audio L/R
(cinch) cable. Match the cable colours when you
connect.
An S-Video cable Audio L/R cable - Red, White
Connections 35
ENGLISH
2705.3 EN  20-05-2008  10:03  Pagina 35
 
						

							Connections
Video - Basic quality ★
Use a Video (cinch) cable together with an Audio
L/R (cinch) cable. Match the cable colours when
y ou connect.
Combined Video - yellow and Audio L/R cable 
- red and white
7.2.2 HDMI with EasyLink
Connected devices that are compliant with the
HDMI CEC standard can work together.
‡ Press  Menu  Ï> Setup > Installation >
Preferences and pressπto enter the list.
® Press  oor œ to select  EasyLink.
Ò Press  πto enter.
† Press  oor œ to select  Onor Off .
º Select  Onto activate EasyLink.
EasyLink might not work with devices from other
brands.
One touch play
Inser t a DVD disc and press Play. The TV switches
on from standby and shows the DVD programme
automatically.
System standby
Press the  Bkey on the remote control for more
than 2 seconds to switch the connected devices in
standby.
System audio control
When you connect an audio system you can listen
to the sound from your TV through your audio
system while the TV speakers are muted. See
section  5.4.5 Sound settings, TV speakers .
r Note
Ensure that all HDMI-CEC features in the HDMI-
CEC devices (for ex. Home Theatre System) are
properly set up.
7.2.3 Display synchronised audio out
For the best match of image and sound in speech
on screen, connect a Home Theatre System to
Audio Out L/R or Digital Audio outputs. See
diagrams  7.4.4and 7.4.8.
Do not connect the audio signal of a DVD player,
digital receiver or other audio/video device directly
to the Home Theatre System.
7.3 Connect with the Connection assistant
(if available)
Use the Connection assistant to show you how to
connect your devices to your TV. It sets all
necessar y settings automatically.
Y ou can also connect your devices without the use
of the Connection assistant. See section  7.4
Connect without the Connection assistant .
‡ Press  Menu  Ïon the remote control and
select Setup > Installation >  Connection
assistant .
® Press  πto star t the Connection assistant.
Ò Press  OK.
7.4 Connect without the
Connection assistant
The connections shown in this section are
recommendations for the most used cases. Other
solutions are possible.
When a device is connected the TV needs to know
what connection you made. See section  7.5
Connection setup .
36
2705.3 EN  20-05-2008  10:03  Pagina 36
 
						

							7.4.1 DVD player
Use a scar t cable to connect the device to the
EXT1input at the back of the TV.
7.4.2 DVD Recorder or Digital Receiver
Use a scar t cable and 2 antenna cables.
7.4.3 DVD Recorder and Digital Receiver
Use 3 scar t cables and 3 antenna cables.
Connections37
ENGLISH
EXT 3
VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VGA / Y Pb Pr  AUDIO
VGA +YPbPr
Receiver / Cable boxD
VD Recorder
IN
OUT
IN
OUT
EXT 3
VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VG
A/YPbPr   AUDIO
VGA +YPbPr
DVD Player
EXT 3
VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VG
A/YPbPr   AUDIO
VGA +YPbPr
DVD Recorder / Digital receiver
IN
OUT
2705.3 EN  20-05-2008  10:03  Pagina 37
 
						

							Connections
7.4.4 DVD Recorder and Home TheatreSystem
Use a scar t cable, 2 antenna cables and 1 digital
audio (cinch) cable.
7.4.5 DVD Recorder and DVD Home Theatre System
Use 2 scar t cables, 2 antenna cables and 1 digital
audio (cinch) cable.
7.4.6 Satellite receiver
Use a scar t cable and 2 antenna cables.
38
EXT 3 VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VG
A/YPbPr   AUDIO
VGA +YPbPr
Home Theatre  SystemDVD Recorder
DIGITAL
AUDIO
INOUTIN
DIGITAL
AUDIO OUT
EXT 3 VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VGA / Y Pb Pr  AUDIO
VGA +YPbPr
Satellite receiver
EXT 3
VGA
SERVICE
UART
OUTYPb
Pr
L
R
L
R
EXT 2EXT 1
AUDIOOUTAUDIO
DIGITAL
VGA / Y Pb Pr  AUDIO
VGA +YPbPr
D
VD Home Theatre SystemDVD Recorder
DIGITAL
AUDIO
INOUTIN
DIGITAL
AUDIO OUT
2705.3 EN  20-05-2008  10:03  Pagina 38