Philips 32pfl9604 User Manual

							6.4      Picture
1/3
LightGuide is on but there is no picture
• Verify if the antenna is connected properly.
• Verify if the correct device is selected.
The sound is on, but there is no picture
• Verify the contrast or brightness setting in the menu. The TV picture is poor
• Verify if the antenna is connected properly.
• Non-earthed audio devices, neon lights, high buildings
or mountains can influence the picture quality. Try to
improve the picture by changing the position of the
antenna or placing devices away from the TV.
• Verify that the correct TV system is chosen in the Manual
installation menu.
• If only a certain channel is poor, try to fine tune this
channel with the Fine tune menu. Read Setup > Installation
> Analogue: manual installation.
... 
						

							6.4      Picture
2/3
The picture has poor colour
• Verify the colour settings in the Picture menu. Select any
of the Smart settings in the Setup menu.
• Verify the connections and cables of the connected
devices.
Picture delay when a game console is connected
• To prevent picture delay, set the TV to game mode. Select
Game in the Smart settings in the Setup menu. The TV does not remember my settings when I switch it
back on
• Check whether the TV is set to Home in the Home menu >
Setup > Installation > Preferences > Location menu.
The picture does not fit the screen; it is either too big or
too small
• Press f and select a more fitting picture format in the
Picture format menu.
... 
						

							6.4      Picture
3/3
The picture position on screen is not correct
• Some picture signals from some devices do not fit the
screen properly. You can move the picture with the cursor
keys on the remote control. Check the signal output of the
device. 
						

							6.5   Sound
There is a picture but no sound
• Verify the volume is not set to 0.
• Verify the sound has not been muted with m.
• Verify that all cables are connected properly.
• If no sound signal is detected, the TV automatically
switches off the sound. This is proper operation and is not
a malfunction.
The sound is poor
• Verify that the sound is set to Stereo.
• Select any of the Smart settings in h > Setup > Smart
settings.
The sound comes from one speaker only
• Verify that the Balance is not set to extreme left or right.
Sound delay when a DVD Home Theatre System device is
connected
• Read the user manual of the DVD device to adjust the
audio sync delay. If you cannot set a delay, switch off HD
Natural Motion in h > Setup > Picture > Perfect Pixel HD. 
						

							6.6      Devices
2/2
• Make sure that the System audio control in your HDMI-
CEC audio devices is properly set up. Read the user manual
that comes with your audio device.
EasyLink Remote control
• Some devices have identical functionality but do not
support the specific remote control commands. Read
Connections > EasyLink HDMI-CEC > EasyLink RC. The PC display on my TV is not stable or is not
synchronised (with TV as PC monitor)
• Set the refresh rate of your PC to 60Hz.
• Verify that the correct resolution mode is selected on
your PC. Read Technical data > Display resolutions. 
						

							6.8   Network
Wireless network not found or distorted.
• Microwave ovens, Dect phones or other WiFi 11b devices
in your neighbourhood might disturb the wireless network.
• Make sure that the firewalls in your network allow access
to the TV wireless connection.
• If the wireless network does not work properly in your
home, try the wired network installation. Read h > Setup >
Installation > Network.
Net TV does not work
• If the connection to the router is OK, verify the router
connection to the Internet.
Browse PC and Net TV work slow
• Look in your wireless router's user manual for
information on indoor range, transfer rate and other
factors of signal quality.
• You need a high speed Internet connection for your
router. 
						

							7.1   Power and reception
Product specifications are subject to change without
notice.
For more specification details of this product see
www.philips.com/support.
Power
• Mains power : AC220-240V +/-10%
• Ambient temperature : 5°C to 35°C
• Power and standby power consumption, see the
technical specification on www.philips.com
Reception
• Antenna input : 75ohm coaxial (IEC75)
• TV system : DVB COFDM 2K/8K,
• Video playback : NTSC, SECAM, PAL
• DVB : DVB-T, DVB-C, MHEG 4
(see selected countries on the TV typeplate)
• Tunerbands : VHF, UHF, S-Channel, Hyperband