Philips 32pdl7906t User Manual

							     
EN      41   
English
 
  
3. When the correct channel frequency is entered, select [Done], then press OK. 
4. Select [Store as new channel], then press 
OK to store the new TV channel.  
Install digital and satellite channels 
Install digital channels 
To improve TV reception, reposition the 
antenna. You need to know the correct 
frequency to tune. For best results, contact 
the service provider or get a professional 
installer. 
1. Press . 2. Select [Setup] > [Channel settings] > 
[Channel installation]. 
3. Select [Digital: Reception test] > 
[Search], then press OK. 
4. Press the Numeric buttons to enter the 
channel frequency. 5. Select [Search], then press OK.   
6. When the correct channel is located, select [Store], then press OK. 
7. Press  to exit.  
Notes 
 If the reception is poor, reposition your 
antenna and repeat the procedure. 
 If you receive the channel with DVB-C, select [Automatic] in [Symbol rate 
mode] unless your cable provider 
supplies you with a specific symbol rate 
value.   
Install satellite channels 
Note: Available on certain models only.  
[Search for satellite] is only available if the 
TV supports DVB-S. 
If your satellite receiver is connected to the 
SAT connector, you can receive satellite 
channels. 
1. While you watch TV, press . 2. Select [Setup] > [Search for satellite] > 
[Reinstall channels]. 
3. Follow the onscreen instructions to 
complete the installation. 4. Once complete, select [Finish], and then 
press OK.    
 
View satellite channels 
To watch satellite channels, press  > [Watch satellite].   
Fine-tune channels 
If the reception of an analogue TV channel is 
poor, fine-tune the TV channel. 
1. Press . 2. Select [Setup] > [Channel settings] > 
[Channel installation]. 
3. Select [Analogue: Manual installation] > 
[Fine tune], and then press OK. 
4. Press  or  to fine-tune the channel. 
5. When you have selected the correct channel frequency, select [Done], and then 
press OK. 
6. Select one of the following options, then press OK. 
 [Store current channel]: Store the 
channel as the current channel number. 
 [Store as new channel]: Store the 
channel as a new channel number.  
Reinstall channels 
ATTENTION: This feature is intended for 
dealers and service personnel. 
You can copy channel lists from one Philips 
TV to another through a USB storage 
device. You do not need to search for 
channels or install them again on the second 
TV. The channel list file is small enough to fit 
on any USB storage device. 
What you need 
The two Philips TVs must have: 
 the same country setting, 
 the same year range,  
 the same DVB type, as indicated by the 
suffix (H, K, T, or D/00) in the model 
name, 
 the same settings for satellite channels, 
including the number of LNB satellites 
 the same hardware type, as indicated 
by the sticker on the back of the TV, 
(for example Qxxx.xx.Lx), and 
 compatible software versions. 
 
 
						

							  
EN      42       
An onscreen message will notify you if the 
channel list cannot be copied to the second 
TV. 
Note: If you are prompted to enter a code, 
enter 8888. 
Copy channel list to USB 
1. Connect a USB storage device to the TV 
with the channels installed on it. 
2. Press . 
3. Select [Setup] > [TV settings] > 
[Preferences] > [Channel list copy] > 
[Copy to USB], then press OK. The channel 
list is copied to the USB storage device. 
4. Unplug the USB storage device.   
Copy channel list to TV with no channels 
installed 
1. Switch on the TV with no channels 
installed on it to start the initial installation. 
Select the language and country. The 
country setting must be the same as that of 
the TV whose channel list you want to copy. 
Skip the search for channels. 
2. Connect the USB storage device 
containing the channel list to the TV. 
3. Press . 4. Select [Setup] > [TV settings] > 
[Preferences] > [Channel list copy] > 
[Copy to TV], then press OK.The channel 
list is copied to the TV. 
5. Unplug the USB storage device.   
Copy channel list to TV with channels 
installed 
1. Switch on the TV on which you want to 
copy the channel list. 
2. Press . 3. Select [Setup] > [Search for channels] > 
[Reinstall channels], then press OK.  
You will be prompted to select the country 
where the TV was installed. Make a note of 
the current setting and press  followed by [Cancel] to exit. 
4. If the country setting on the TV is different 
from that of the TV whose channel list you 
want to copy, reinstall the TV and select the country setting to match the first TV. See Set 
up your TV > Reinstall the TV (Page 45). 
5. Connect the USB storage device 
containing the channel list to the TV where 
you want to copy the channel list. 
6. Select [Setup] > [TV settings] > 
[Preferences] > [Channel list copy] > 
[Copy to TV], then press OK. The channel 
list is copied to the TV storage device. 
7. Unplug the USB storage device.  
Menu language 
1. While you watch TV, press . 2. Select [Setup] > [TV settings] > 
[Preferences] > [Menu language]. 
3. Select a menu language from the list, then press OK.  
Set universal access 
Switch on 
Some digital TV broadcasters provide special 
audio and subtitle features for people who 
are hearing or visually impaired.  
To enable these features, turn on universal 
access in the preference menu. 
1. Press . 2. Select [Setup] > [TV settings] > 
[Preferences]. 
3. Select [Universal access] > [On], then 
press OK.  
Hearing impaired 
Tip: To verify whether a hearing impaired 
audio language is available, press  OPTIONS and select [Audio language]. 
Languages with an ear icon support hearing 
impaired audio. 
 
						

							     
EN      43   
English
 
To switch on hearing impaired audio and 
subtitles 
1. While you watch TV, press  OPTIONS. 
2. Press one of the following buttons to 
select an option: 
 Red: Switch hearing impaired on or off. 
 Green: Switch on hearing impaired 
audio and subtitles. 
3. Press  to exit. 
Visually impaired 
Tip: To verify whether visually impaired 
audio is available, press  OPTIONS and 
select [Audio language]. Languages with an 
eye icon support visually impaired audio. 
To switch on visually impaired audio (if 
available) 
1. While you watch TV, press  OPTIONS. 
2. Press the green button to select [Visually 
impaired]. 
3. Press one of the following buttons to 
select an option:    Red - [Off]: Turn off visually impaired 
audio. 
 Yellow - [Headphones]: Hear visually 
impaired audio from headphones only. 
(if applicable) 
 Green - [Speakers]: Hear visually 
impaired audio from speakers only. 
 Blue - [Speakers + headphones]: Hear 
visually impaired audio from speakers 
and headphones. 
4. Press  to exit. 
Note: If the EasyLink remote control is 
enabled, you cannot select the green or yellow buttons. To disable, see Use more of 
your TV > Use EasyLink > Switch on (Page 
35).   
Adjust volume for the visually impaired 
1. In the [Universal access] menu, press the 
yellow button to select [Mixed volume]. 
2. Press the Navigation buttons to move the 
slider up or down, then press OK. 
3. Press  to exit. 
  
Audio feedback for the visually impaired 
This feature enables audio feedback when 
buttons are pressed on the remote control 
or TV. 
1. In the [Universal access] menu, press the 
blue button to select [Key beep]. 
2. Press the green button to turn on audio 
feedback, or press the red button to turn it 
off. 
3. Press  to exit.  
Other settings 
TV demo 
Start a demo to find out more about your 
TVs features. 
Note: Demos are not supported on MHEG 
channels. 
1. While you watch TV, press . 2. Select [Setup] > [Watch demos], then 
press OK. 
3. Select a demo, then press OK. 
4. Press  to exit.  
Update software 
TV software 
Check software version 
1. Press . 2. Select [Setup] > [Software settings] > 
[Current software info], then press OK.  
The version of the current software is 
displayed. 
Caution: Do not install a lower version of 
software than the current version installed 
on your product. TP Vision cannot be held 
liable or be made responsible for problems 
caused by a software downgrade. 
Update the software through one of these 
options: 
 update with USB flash drive 
 update from digital broadcast 
 update from the Internet 
 
						

							  
EN      44       
For more information, see the following 
pages.   
Update with USB 
Before performing this procedure, make sure 
that you have the following: 
 Spare time to complete the entire 
update. 
 A USB flash drive that has at least 
256MB of storage space, is FAT or 
DOS formatted, and has its write 
protection disabled. 
 Access to a computer with a USB port 
and internet access. 
Note: Do not use a USB hard drive. 
1. Press . 2. Select [Setup] > [Update software], then 
press OK.   
The update assistant starts.   
3. Follow the onscreen instructions to start 
the update. 
Note: The update assistant directs you to 
the Philips support website. Refer to the 
installation instructions on the website to 
complete the update. 
Update from the Internet 
To update the TV software directly from the 
Internet, connect the TV to the Internet 
through a router with a high-speed 
connection.  
1. Press  > [Setup] > [Update software], 
then press OK. 
2. Select [Internet], then press OK.   
3. Follow the onscreen instructions to start 
the update. 
When the update is complete, the TV 
switches off and back on again automatically. 
Wait for the TV to switch back on. Do not 
use the power switch on the TV or the 
remote control. 
Note: If the TV is connected to the Internet, 
the TV displays the availability of new 
software at startup. NonPu bl i sh 
 
 
 
 
Update from digital broadcast 
When available, your TV can receive 
software updates through digital broadcasts. 
A message appears prompting you to update 
the software. We strongly recommend that 
you update the software when prompted.  
Follow the instructions on screen. 
Note: If you choose to update the software 
at a later time, select  > [Setup] > 
[Software settings] > [Local updates]. 
Onscreen Help 
What you need 
Before you update the onscreen [Help], 
make sure that you have the following: 
 A USB storage device that is FAT or 
DOS-formatted. 
 A PC with Internet access. 
 An archive utility that supports the ZIP 
file format (for example, WinZip for 
Microsoft Windows or Stufflt for 
Macintosh). 
Note: Do not use a USB hard drive.  
Download the latest file 
1. Insert a USB storage device into the USB 
connector on your PC.   
2. Create a folder named ‘upgrades’ in the 
root directory of the USB storage device. 
3. In your web browser, navigate to www.philips.com/support. 
4. At the Philips Support site, find your product and locate the [Help] file for your 
TV. The file (a *.upg file) is compressed into 
a *.zip archive.   
5. If the [Help] file is a later version than the 
file in your TV, click it.   
6. Save it to your PC. 
7. Using an archive utility, extract the *.upg 
file from the *.zip file. 
8. Save the *.upg file to the ‘upgrades’ folder 
in the USB storage device. 
9. Disconnect the USB storage device from 
the PC.   
 
 
 
 
						

							     
EN      45   
English
 
Update [Help] 
 Do not switch off the TV or remove 
the USB storage device during the 
update. 
 If a power failure occurs during the 
update, do not remove the USB 
storage device from the TV. The TV 
continues to update as soon as power 
is restored. 
 If an error occurs during the update, 
retry the procedure. If the error 
reoccurs, contact Philips Consumer 
Care.   
1. Switch on the TV. 
2. Disconnect all other USB devices from the 
TV. 
3. Connect the USB storage device 
containing the *.upg file to the USB 
connector on the TV.   
4. Press . 
5. Select [Setup] > [Software settings] > 
[Local updates]. 
The updates screen appears. 6. Select the *.upg file and press OK. 
A message displays the update status.   
7. Follow the onscreen instructions to 
complete the update and restart your TV.  
Reinstall the TV 
Reinstall your TV to reset all picture and 
sound settings and reinstall all TV channels. 
1. Press . 2. Select [Setup] > [TV settings] > 
[Reinstall TV], then press OK. 
3. Follow the onscreen instructions.  
 
						

							  
EN      46       
5 Connect your 
TV 
About cables 
Cable quality  
Overview 
Before you connect devices to the TV, check 
the available connectors on the device. 
Connect the device to the TV with the 
highest quality connection available. Good 
quality cables ensure a good transfer of 
picture and sound. 
The connections shown in this user manual 
are recommendations only. Other solutions 
are possible. Tip: If your device only has composite or 
RCA connectors, use a SCART-cinch 
adapter to connect the device to a SCART 
connector on the TV.  
HDMI 
An HDMI connection has the best picture 
and sound quality. 
 An HDMI cable combines video and 
audio signals. Use HDMI for high-
definition (HD) TV signals, and to 
enable EasyLink. 
 An HDMI Audio Return Channel 
(ARC) connector allows output of TV 
audio to an HDMI ARC compliant 
device. 
 Do not use an HDMI cable longer than 
5 meters / 16.4 feet. 
  
Y Pb Pr 
Use the Component Video (Y Pb Pr) 
connection together with an Audio Left and 
Right connection for sound. 
Y Pb Pr can handle high-definition (HD) TV 
signals. 
Match the Y Pb Pr connector colours to the 
cable plugs.  
  
   
						

							     
EN      47   
English
 SCART 
A SCART cable combines video and audio 
signals. 
SCART connectors can handle RGB video 
signals but cannot handle high-definition 
(HD) TV signals. 
  
VGA 
Use this connection to display PC content 
on the TV. 
For video and sound, use the VGA and 
AUDIO IN connectors. 
  
Connect devices 
Overview 
You can connect your devices to the TV with any of the following options. After connection, press  > [Add your devices]. 
  
    
						

							  
EN      48       
Blu-ray or DVD disc player 
Connect the disc player with an HDMI cable to the TV.  
   
Connect the disc player with a component cable (Y Pb Pr) and an audio L/R cable to the TV.  
  
TV receiver 
Connect the satellite or digital TV receiver with an antenna cable to the TV. (SAT is available on 
certain models only.) 
 
    
						

							     
EN      49   
English
 
  
Connect the satellite or digital TV receiver with an HDMI cable to the TV. 
   
Connect the satellite or digital TV receiver with a SCART cable to the TV. 
   
Connect the satellite or digital TV receiver with a component cable (Y Pb Pr) and an audio L/R 
cable to the TV. 
  
    
						

							  
EN      50       
Recorder 
Connect the recorder with an antenna cable to the TV. (SAT is available on certain models only.) 
   
Connect the recorder with a SCART cable to the TV. 
   
Connect the recorder with a component cable (Y Pb Pr) and an audio L/R cable to the TV. 
  
Game console 
The most practical connectors for a game 
console are on the side of the TV. However, 
you can also use the connectors at the back 
of the TV. 
For the best gaming experience, set the TV 
to game mode. 
1. Press  ADJUST. 
2. Select [Smart picture] > [Game], then 
press OK. 
3. To exit, press .