Philips 32hfl4351d User Manual

							19
English
EN
Update using OAD (On the Air 
software Download)
If Professional mode is [On], your TV automatically 
receives software updates in semi-standby mode 
without notice on screen. The TV restar ts after the 
software update is complete.
Change TV preferences
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Preferences].
3 Press OK or to enter [Preferences].
[Location] • Optimises T V settings for 
your location - home or shop.
Note
If [Shop] mode is selected:
The • [Smart picture] set ting will be switched to [Vivid] automatically to display the brightest backlight on screen.
E-sticker is applicable to display the T V selling  •features on screen.
[Volume bar]•  Displays the volume bar 
when adjusting the volume.
[Channel info.]•  Displays information 
about the T V channel ever y time you 
switch channels. Select [Full] to view 
channel information or [Off ] to turn off 
the channel information.
[EasyLink] • Enables one-touch play and 
one-touch standby between EasyLink 
compliant devices.
[E-sticker]•  For shop mode only. Sets the 
location of the e-sticker.
Access decoder channel
You can map channels provided through a 
decoder or descrambler to your TV channel 
selection. In this way, you can select these 
channels by using the RC of your TV. The 
decoder or a descrambler must be connected 
to EXT1 (SCART). 
Set decoder channel
Map channels from a decoder or descrambler
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Preferences] > 
[Decoder].
3 Press OK or  to enter [Decoder] menu 
.
4 Press  to select [Channel] and press 
OK or  to enter.
A list of analogue channels appears on  »
the screen.
5 Press  to select one channel to map 
to the decoder/descrambler channel and 
press OK to confirm.
6 Select [St atus] and press OK or  to 
enter.
7 Press  to select [EXT 1] (SCART ) 
the connector used by the decoder/
descrambler.
8 Press OK.
9 Press EXIT to exit.
 
						

							20EN
Start a TV DEMO
Note
Before star ting DEMO, make sure to activate one of the following setting for TV DEMO to take effect:1. [PBS settings] > [PBS mode] > [Off].2. [PBS settings] > [Applications] > [Signage].
1 Press Red button (DEMO) on the 
remote control.
2 Press  to select a demo and press OK 
to view it.
3 Press Red button (DEMO) to exit.
Reset the TV to factory 
settings
You can restore the default picture and sound settings of your TV. Channel installation settings remain the same.
1 Press MENU.
2 Press  to select [Setup] > [Installation] > [Factory settings].
3 Press OK or  to enter the [Factory settings] menu.A factor y setting message appears. »
4 Select [Reset] to star t resetting.
5 Press EXIT to exit.
 
						

							21
English
EN
6 Install channels
The first time you set up your TV, you are 
prompted to select a menu language and to 
install TV and digital radio channels (if available). 
This chapter provides instructions on how to 
re-install and fine tune channels.
Automatically install channels
This section describes how to search and store 
channels automatically.
Step 1 Select your menu language
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Language] > [Menu 
language].
3 Press OK or  to enter [Menu language].
  
4 Press  to select a language setting.
5 Press OK to confirm.
6 Press  to return to [Installation] menu.
Step 2 Select your country
Select your countr y for proper channel 
installation. 
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel install.] > 
[Channel assistant].
ClMenu languag eockPrimary subtitle in
Picture
Sound
Features
Installation
Software updat
e
Decoder
Language
Channel install.
Preferences
Decoder
Clock
Factory settings Menu language
Primary audio language
Secondary audio language
- - - 
-
- - -  -
- - -  -
- - -  -
Hearing impairedMenu language English
  
3 Press OK or  to enter the menu.
The countr y menu appears. »
  
4 Press  to select your countr y.
5 Press OK to confirm your choice.
The channel installation guide appears  »
on the screen.
Step 3 Install channels
Install the available analogue and digital 
T V channels and digital radio channels 
automatically.
1 From the channel installation guide screen 
, select [Full installation] to automatically 
install all T V channels and digital radio 
channels.
  
2 Press OK to confirm.
The TV star ts to search and store all  »
the available channels. 
Language
Channel install .
Preferences
Decoder
Clock
Factory settingsMenu language
Channel assistan t
Locatio n
Channel
Auto clock
ActionPicture
Sound
Features
Installation
Software updat e
Select your countr y, 
then press OKSlovakia
Sloveni a
Spain
Sweden
Switzerlan d
Tu rkey
Ukraine
UK
Start automatic installation .
This takes a few minutes.
Full installation
Skip installation
 
						

							22EN
  
3 Press OK or  to enter [System] menu.
4 Press  to select your countr y or 
region.
5 Press OK to confirm.
6 Press  to return to [Channel install.] 
menu.
Step 2 Search and store new TV 
channels
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel install.] > 
[Analogue: Manual].
The  »[Analogue: Manual] menu appears.
3 Press  to select [Search] and then OK 
or  to enter [Search].
4 Press  to manually enter the three-
digit frequency.
5 Press OK to begin search.
If a channel is unavailable at the  »
selected frequency, press OK to search 
for the next available channel.
6 Press ◄ when the new channel is found.
7 Press  to select [Store new channel] 
to store the new channel under a new 
channel number.
8 Press OK or  to enter [Store new 
channel] and press OK.
9 Press  to return to the [Analogue: 
Manual] menu.
Sound
Features Preferences
Start up message
Digital Test recept...
Picture
Sound
Features
Installation
Software update
Decoder
Language
Channel install.
Preferences
Decoder
Clock
Factory settings Channel assistan
t
Standby updat e
Analogue: Manual
Analogue: ManualSystem 
3 When installation is complete, press OK 
to return to [Installation] menu.
Step 4 Update the channel list
You can choose to enable standby mode auto 
update of channels. If you enable this feature, 
the new channels stored in your T V will be 
updated ever y morning according to the 
channel information in the broadcast.
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel install.] > 
[Standby update].
3 Select [On] to enable the automatic 
update or select [Of f ] to disable it.
Manually install channels
This section describes how to search and store 
analogue TV channels manually.
Step 1 Select your system
Note
Skip this step if your system set tings are  •correct.
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel install.] > 
[Analogue: Manual].
The  »[Analogue: Manual] menu appears.
System searching. Please wait .
Stop
Digital channels found
Analogue channels found7
0
 
						

							23
English
EN
Reorder channels
After you install channels, you can rearrange the order in which they appear.
1 When watching T V, press OK to display the channel grid .
2 Press b(OPTIONS).The channel options menu appears. »
3 Press  to select [Reorder] and then OK to return to the channel grid.
4 Press  to select the channel you want to reorder and press OK.The selected channel is highlighted. »
5 Press  to move the highlighted channel to your preferred position and press OK.
6 Press b(OPTIONS). »[Done reordering] appears on the screen.
7 Press OK to finish reordering.
Test digital reception
If using digital broadcasts, you can check the quality and signal strength of digital channels. This allows you to reposition and test your antenna or satellite dish.
1 Press MENU.
2 Press  to select [Setup] > [Installation] > [Channel install.] > [Digital: test recept].
3 Press OK or  to enter the menu.
4 Press  to enter the frequency of the channel you want to test.
5 Press OK to confirm the frequency and then press OK again to confirm [Search].
6 When complete, select [Store] to store 
the frequency.
Note
If the signal quality and streng th is poor,  •reposition the antenna or satellite dish and retest.If you still have problems with the reception  •of your digital broadcast, contact a specialised installer.
Step 3 Fine-tune analogue channels
1 Press MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel install.] > 
[Analogue: Manual].
The  »[Analogue: Manual] menu appears.
3 Press  to select [Fine-tune] and then 
OK or  to enter [Fine-tune].
4 Press  to adjust frequency.
5 Press OK when done.
6 Press  to select [Store current 
channel] to store the fine-tuned channel 
under the current channel number.
7 Press OK or  to enter [Store curr. 
chan.] and press OK.
8 Press  to return to the [Channel install.] 
menu.
Rename channels
Channels can be renamed so that a name of 
your choice appears whenever the channel is 
selected.
1 When watching T V, press OK to display 
the channel grid .
2 Press  to select the channel you 
want to rename.
3 Press  b(OPTIONS).
The channel options menu appears. »
4 Press  to select [Rename channel].
A text input box appears. »
5 Press  to select and change 
characters.
6 Select [Done] to finish renaming 
channels.
Tip
Use  •[A a] to change upper-case let ter to lower-case let ter and vice versa.
 
						

							24EN
7 Professional 
mode 
instruction
Introduction
Included in this TV is a special functional mode that allows the TV to be configured for Hospitality or Signage applications. This feature is called Professional mode.
This section has been designed to help install and operate this TV in Professional mode. Before reading this section, please read section 3 to 6 to set the basic functionality of this TV.
Benefits	of	Professional	mode
This TV is specially designed to operate in Professional Mode. Professional Mode offers the following benefits:
Access to the • [Consumer Menu] can be 
blocked.  This prevents users (e.g. guests) 
from deleting or changing channel settings 
and/or modifying picture and sound 
settings. This ensures that T Vs are always 
set up correctly.
A switch-on volume and channel can be • 
selected.  Af ter switching on, the T V will 
always star t on the specified volume level 
and channel.
The maximum volume level of the T V can • 
be limited in order to prevent disturbance 
to other guest.
Channels can be blanked ( Video only).• 
The T V local buttons • VOLUME +/-, P/
CH+/- and SOURCE can be locked
Screen information can be suppressed.• 
 
Professional Setup Remote 
control (2573 optional)
0
a
b
c
 
						

							25
English
EN
a C button (OPTIONS)Accesses options relating to the current activity or selection. (Equals to the function of b(OPTIONS) on Guest remote control).
b E button (OK)Confirms an entr y or selection.
c (Enters Professional setup menu)Selects • SETUP mode first.Press • M button to enter the Professional setup menu.
Note
 •SETUP mode should be selected for hotel installer.
Activating the Professional 
mode setup menu
1  Switch on the T V and select a T V channel.
2 Press the following buttons to access 
Professional mode setup menu:
[3,•  1, 9, 7, 5, 3+¬(MUTE)] on Guest 
remote control.
M button•  on Professional setup 
remote control. ( When SETUP mode 
is selected on the Professional setup 
remote control.)
3 Press ▲▼◄► on the remote control to 
select and change any of the settings.
4 Select [PBS settings] > [Store] and select 
[Confirm] to save the setting. Press MENU 
/ EXIT to exit Professional mode menu without saving.
5 For Professional mode settings to take effect, 
you must restar t the TV mains power.
 
						

							26EN
Professional mode options
This paragraph describes the functionality of each item in the Professional mode setup menu.
Layer 1Layer 2Layer 3
PBS settingsPBS modeOff / On
ApplicationHospitality / Signage
Consumer setupAction
Smar tloader / USB to TVAction
TV to Smar tloader / USBAction
StoreAction
Reset0~60
Switch on settingsMaximum volume0 ~ 60
Switch on picture formatAuto format / Super zoom / 4:3 / Subtitle Zoom 
/ Movie expand 14:9 / Movie expand 16:9 / Wide 
screen / Unscaled
Low power standby (Green / Fast)Fast / Green
Power onOn / Standby / Last status
Smar t powerOff / Low / Medium / High
Display messageOff / On
Set ID (Only available in Signage 
mode)
Serial Xpress Adress ID range: 0~63
Switch on volumeLast statusOff / On
User defined0 ~ 60
Switch on channelLast statusOff / On
User defined[List of channels]
Welcome messageLine 1Edit
Line 2Edit
ClearAction
Message Time-out20 sec / 25 sec / 30 sec
Control settingsLocal KB blockOff / On / All
RC lockOff / On
OSD displayOff / On
High security modeOff / On
Auto scar tOff / On (EXT 1 / EXT 2 / Power scar t)
HDMI-CEC inOff / On
USB break inOff / On
Monitor outOff / On
 
						

							27
English
EN
Layer 1Layer 2Layer 3
Enable teletextFor PrisonOff / On
Enable MHEGOff / On
Enable EPGOff / On
Enable subtitleOff / On
Clock setup (Only 
available for some 
models)
Display standbyOff > 1 > 2 > 3 > 4 > 5
Display onOff > 1 > 2 > 3 > 4 > 5
Time settingTime setup table
Time downloadOn / Off
Download programList of Analogue / Digital channels.
Time offsetGMT: -12 > ....> 0 > ... > 12
Buzzer volumeOff / Low / High
Speaker settingsTV speaker enableOn / Off
Independent main speaker muteOn / Off
Default main speaker volume0 ~ Max
InstallationBlank channelAll available channels.
Disable auto updatingSoftware / Channels / Both / Off
Skip scrambled signalsOff / On
Smar t RCOff / On
Multi remote controlBlue / Green / Yellow / Red / Off
Add current 
channel to PayTV 
ring
R0All available channels.
R1Pay TV channel list.
R2Pay TV channel list
 
						

							28EN
PBS settings
[PBS mode]
Enables / disables the Professional mode.  
[On]: • All settings in the Professional 
mode Setup menu are in effect.
[Off ]: • The T V operates as a normal 
(consumer) T V.
[Application] 
1 When application is [Hospitality], the 
following are activated.
Last status is disabled.• 
Limited Consumer menu:  When • 
in Professional mode, the guest can 
display the Consumer menu to adjust 
T V parameters.  However, these 
settings will not be stored in T V 
me mor y.
T V lock and parental ratings (except • 
Sleep timer) are disabled.
Entr y into ser vice mode is disabled • 
in order to prevent the guest from 
changing ser vice settings.
2 When application is [Signage], the below 
functions behave as per normal consumer.
Last status is enabled.• 
The full T V menu can be accessed and • 
changes are stored in T V memor y.
T V lock and parental ratings are • 
enabled.
Entr y into ser vice mode is enabled.• 
Note
 •The default application for TV should be [Hospitality], while that for monitor should be [Signage].
[Consumer setup]
A shor tcut to enter the full TV menu. This 
allows the installers to do all the TV setup 
settings. 
Note
Selects  •[PBS settings] > [Store] to save the changes in the [Consumer setup menu].
[Smartloader / USB to TV]
Loads the TV configuration data (including the 
video,  audio,  channel Table, and Professional 
mode settings) from a Smar tloader / USB device 
to the TV set.
[TV to Smartloader / USB]
Loads the TV configuration data (including the 
video, audio, channel Table, and Professional mode 
settings) from the TV set to a Smar tloader /USB 
device.
[Store]
Selects [Confirm] to store Professional mode 
settings.
Note
After storing the settings, refer to page 29 
“Low power standby (Green / Fast)”:When • [Fast] is selected, you need to restar t the TV mains power for the changes in Professional mode to take effect.When • [Green] is selected, you need to switch the TV from standby to on again for the changes in Professional mode to take effect.
[Reset]
Selects [Yes] to reset all settings in Professional 
mode to factor y default. 
Switch on settings
[Maximum volume]
This option specifies the maximum allowable 
volume level of the TV.
[Switch on picture format]
Sets available picture format when the TV is 
switched on.
Note
If the picture format is not suppor ted  •with the activated source, [Auto format] detection is applied.