Philips 220aw8f User Manual

							
   
       
 
 
• Safety and 
Troubleshooting
 • FAQs
 • Common Problems
 • Imaging Problems 
 
• Regulatory  Information
 • Other Related Information
  
  
  
  
Troubleshooting
This page deals with problems that can be corrected by the user. If the \
problem still persists 
after you have tried these solutions, contact your nearest Philips deale\
r.
Common Problems 
Having this problem Check these items
No Picture
(Power LED not lit) 
l     Make sure the power cord is plugged 
into the power outlet and into the 
back of the monitor. 
l     First, ensure that the power button on 
the front of the monitor is in the OFF 
position, then press it to the ON 
position.
 
No Picture
(Power LED is amber or yellow) 
l     Make sure the computer is turned on. 
l     Make sure the signal cable is properly 
connected to your computer. 
l     Check to see if the monitor cable has 
bent pins.
 
l     The Energy Saving feature may be 
activated
 
Screen says
l     Make sure the monitor cable is 
properly connected to your computer. 
(Also refer to the Quick Set-Up 
Guide). 
l     Check to see if the monitor cable has 
bent pins. 
l     Make sure the computer is turned on. 
Screen says
l     Make sure the vertical sync of input 
signal is within the range of 56 ~ 75 
Hz.
l     Change the refresh rate to 56~75Hz 
within 10 minutes. 
l     Re-power on monitor to start over 
again if you failed to change the 
refresh rate within 10 minutes. 
AUTO button not working properly
l     The Auto Function is designed for 
use on standard Macintosh or IBM-
compatible PCs running Microsoft 
Windows. 
l     It may not work properly if using 
nonstandard PC or video card.
l     The AUTO adjustment does not 
function when digital input is used for 
display.
 
						

							
 
Imaging Problems
Display position is incorrect
l     Press the Auto button. 
l     Adjust the image position using the 
Horizontal Position and/or Vertical 
Position in OSD Main Controls.
 
Image vibrates on the screen
l     Check that the signal cable is 
properly connected to the graphics 
board or PC.
 
Vertical flicker appears
 
 
l     Press the Auto button. 
l     Eliminate the vertical bars using the 
Phase/Clock of More Settings in OSD 
Main Controls.
 
Horizontal flicker appears
 
 
l     Press the Auto button. 
l     Eliminate the vertical bars using the 
Phase/Clock of More Settings in OSD 
Main Controls.
The screen is too bright or too dark
l     Adjust the contrast and brightness on 
OSD Main Controls. (The backlight of 
the LCD monitor has a fixed life span. 
When the screen becomes dark or 
begins to flicker,
 please contact your 
dealer).
An after-image appears
l     If an image remains on the screen for 
an extended period of time, it may be 
imprinted in the screen and leave an 
after-image. This usually disappears 
after a few hours
An after-image remains after the 
power has been turned off.
l     This is characteristic of liquid crystal 
and is not caused by a malfunction or 
deterioration of the liquid crystal. The 
after-image will disappear after a 
peroid of time.
    
 
   
 
						

							
Green, red, blue, dark, and white dots 
remains
l     The remaining dots are normal 
characteristic of the liquid crystal 
used in today’s technology.
 
For further assistance, refer to the Consumer Information Centers list and contact your 
local Philips distributor.
 
RETURN TO TOP OF THE PAGE
 
      
 
						

							
   
       
 
 
•
CE Declaration 
of Conformity
 •Energy Star 
Declaration
 
•Federal 
Communications 
Commission 
(FCC) Notice (U.
S. Only)
 •FCC Declaration of Conformity
 
•Commission Federale de la 
Communication 
(FCC 
Declaration)
 
•EN 55022 Compliance 
(Czech Republic 
Only)
 
•VCCI Class 2 Notice (Japan 
Only)
 
•MIC Notice (South Korea 
Only)
 
•Polish Center for Testing and 
Certification 
Notice
 
•North Europe (Nordic 
Countries) 
Information
 •BSMI Notice (Taiwan Only)
 
•Ergonomie Hinweis (nur 
Deutschland)
 •Philips End-of-Life Disposal
 •Information for 
UK only
 •Waste Electrical 
and Electronic 
Equipment-
WEEE
 •
China RoHS
 •Troubleshooting
 •Other Related 
Information
Regulatory Information
Model ID: 220AW8
Model No: HWS8220Q 
CE Declaration of Conformity
Philips Consumer Electronics declare under our responsibility that the p\
roduct is in 
conformity with the following standards 
- EN60950-1:2001 (Safety requirement of Information Technology Equipmen\
t) 
- EN55022:1998 (Radio Disturbance requirement of Information Technology\
 Equipment) 
- EN55024:1998 (Immunity requirement of Information Technology Equipmen\
t) 
- EN61000-3-2:2000 (Limits for Harmonic Current Emission) 
- EN61000-3-3:1995 (Limitation of Voltage Fluctuation and Flicker)
following provisions of directives applicable
- 73/23/EEC (Low Voltage Directive) 
- 89/336/EEC (EMC Directive) 
- 93/68/EEC (Amendment of EMC and Low Voltage Directive) 
and is produced by a manufacturing organization on ISO9000 level. 
The product also comply with the following standards 
- ISO9241-3, ISO9241-7, ISO9241-8 (Ergonomic requirement for CRT Monito\
r) 
- ISO13406-2 (Ergonomic requirement for Flat Panel Display) 
- GS EK1-2000 (GS specification) 
- prEN50279:1998 (Low Frequency Electric and Magnetic fields for Visual\
 Display) 
- MPR-II (MPR:1990:8/1990:10 Low Frequency Electric and Magnetic fields\
) 
- TCO99, TCO03 (Requirement for Environment Labelling of Ergonomics, \
Energy, Ecology 
and Emission, TCO: Swedish Confederation of Professional Employees) for\
 TCO versions
 
RETURN TO TOP OF THE PAGE
 
Energy Star Declaration
This monitor is equipped with a function for saving energy which support\
s the VESA 
Display Power Management Signaling (DPMS) standard. This means that th\
e monitor 
must be connected to a computer which supports VESA DPMS. Time settings \
are 
adjusted from the system unit by software.
NUTEKVESA StateLED IndicatorPower Consumption
Normal operation ON (Active) Green
< 49W (TYP)

Power Saving
Alternative 2
One step OFF (Sleep) 
Amber< 1 W
 Switch Off OFF< 1 W
 
						

							
 
•Frequently Asked 
Questions 
(FAQs)
As an ENERGY STAR® Partner, PHILIPS has determined that this 
product meets the 
ENERGY STAR® guidelines for energy efficiency.
We recommend you switch off the monitor when it is not in use for a long\
 time.
RETURN TO TOP OF THE PAGE
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a\
 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limi\
ts are 
designed to provide reasonable protection against harmful interference i\
n a 
residential installation. This equipment generates, uses and can radiate\
 radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a par\
ticular 
installation. If this equipment does cause harmful interference to radio\
 or 
television reception, which can be determined by turning the equipment o\
ff 
and on, the user is encouraged to try to correct the interference by one\
 or 
more of the following measures:
 
l     Reorient or relocate the receiving antenna. 
l     Increase the separation between the equipment and receiver. 
l     Connect the equipment into an outlet on a circuit different from that to\
 which the 
receiver is connected. 
l     Consult the dealer or an experienced radio/TV technician for help. 
Changes or modifications not expressly approved by the party responsible\
 for 
compliance could void the users authority to operate the equipment. 
Use only RF shielded cable that was supplied with the monitor when conne\
cting this monitor 
to a computer device. 
To prevent damage which may result in fire or shock hazard, do not expos\
e this appliance to 
rain or excessive moisture. 
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN 
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.  RETURN TO TOP OF THE PAGE
FCC Declaration of Conformity
Trade Name:Philips 
Responsible Party: Philips Consumer Electronics North America 
P.O. Box 671539 
Marietta , GA 30006-0026 
1-888-PHILIPS (744-5477) 
 
						

							
Declaration of Conformity for Products Marked with FCC Logo, United Stat\
es Only
This device complies with Part 15 of the FCC Rules. Operation is subject\
 to the following two 
conditions: (1) this device may not cause harmful interference, and (\
2) this device must 
accept any interference received, including interference that may cause \
undesired operation.RETURN TO TOP OF THE PAGE
Commission Federale de la Communication (FCC Declaration)
Cet équipement a été testé et déclaré conforme auxlimi\
tes des appareils 
numériques de class B,aux termes de larticle 15 Des règles de la \
FCC. Ces 
limites sont conçues de façon à fourir une protection raisonnab\
le contre les 
interférences nuisibles dans le cadre dune installation résidenti\
elle. CET 
appareil produit, utilise et peut émettre des hyperfréquences qui,\
 si lappareil 
nest pas installé et utilisé selon les consignes données, peuv\
ent causer des 
interférences nuisibles aux communications radio. Cependant, rien ne \
peut 
garantir labsence dinterférences dans le cadre dune installation p\
articulière. 
Si cet appareil est la cause dinterférences nuisibles pour la réc\
eption des 
signaux de radio ou de télévision, ce qui peut être décelé\
 en fermant 
léquipement, puis en le remettant en fonction, lutilisateur pourrai\
t essayer de 
corriger la situation en prenant les mesures suivantes:
 
l     Réorienter ou déplacer lantenne de réception. 
l     Augmenter la distance entre léquipement et le récepteur. 
l     Brancher léquipement sur un autre circuit que celui utilisé par l\
e récepteur. 
l     Demander laide du marchand ou dun technicien chevronné en radio/té\
lévision. 
Toutes modifications nayant pas reçu lapprobation des services comp\
étents 
en matière de conformité est susceptible dinterdire à lutilis\
ateur lusage du 
présent équipement.
Nutiliser que des câbles RF armés pour les connections avec des o\
rdinateurs ou 
périphériques. 
CET APPAREIL NUMERIQUE DE LA CLASSE B RESPECTE TOUTES LES EXIGENCES DU 
REGLEMENT SUR LE MATERIEL BROUILLEUR DU CANADA.  RETURN TO TOP OF THE PAGE
EN 55022 Compliance (Czech Republic Only)
 
						

							
RETURN TO TOP OF THE PAGE
VCCI Notice (Japan Only)
This is a Class B product based on the standard of the Voluntary Control\
 Council for 
Interference (VCCI) for Information technology equipment. If this equi\
pment is used near a 
radio or television receiver in a domestic environment, it may cause rad\
io Interference. Install 
and use the equipment according to the instruction manual.
Class B ITE 
 
RETURN TO TOP OF THE PAGE 
MIC Notice (South Korea Only)
Class B Device
Please note that this device has been approved for non-business purposes\
 and may be used 
in any environment, including residential areas.RETURN TO TOP OF THE PAGE
 
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protectio\
n circuit (a three-
prong socket). All equipment that works together (computer, monitor, p\
rinter, and so on) 
should have the same power supply source.
The phasing conductor of the rooms electrical installation should have \
a reserve short-circuit 
protection device in the form of a fuse with a nominal value no larger t\
han 16 amperes (A).
 
						

							
 
To completely switch off the equipment, the power supply cable must be r\
emoved from the 
power supply socket, which should be located near the equipment and easi\
ly accessible.
A protection mark B confirms that the equipment is in compliance with \
the protection usage 
requirements of standards PN-93/T-42107 and PN-89/E-06251.
RETURN TO TOP OF THE PAGE
North Europe (Nordic Countries) InformationPlacering/Ventilation 
VARNING: 
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIG\
A, 
NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS. 
 
Placering/Ventilation 
ADVARSEL: 
SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT 
ER NEMT TILGÆNGELIGE. 
 
    
 
   
 
						

							
Paikka/Ilmankierto 
VAROITUS: 
SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA 
HELPOSTI IRROTTAA PISTORASIASTA. 
 
Plassering/Ventilasjon 
ADVARSEL: 
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR \
STØMTILFØRSEL ER LETTE Å NÅ. 
RETURN TO TOP OF THE PAGE
BSMI Notice (Taiwan Only)
 
RETURN TO TOP OF THE PAGE
Ergonomie Hinweis (nur Deutschland)
Der von uns gelieferte Farbmonitor entspricht den in der Verordnung ü\
ber den Schutz vor 
Schäden durch Röntgenstrahlen festgelegten Vorschriften. 
Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf \
die Unbedenklichkeit der 
Inbetriebnahme hinweist, da die Vorschriften über die Bauart von Stö\
rstrahlern nach Anlage 
III ¤ 5 Abs. 4 der Röntgenverordnung erfüllt sind. 
Damit Ihr Monitor immer den in der Zulassung geforderten Werten entspric\
ht, ist darauf zu 
achten, daß 
1.  Reparaturen nur durch Fachpersonal durchgeführt werden. 
2.  nur original-Ersatzteile verwendet werden. 
3.  bei Ersatz der Bildröhre nur eine bauartgleiche eingebaut wird. 
Aus ergonomischen Gründen wird empfohlen, die Grundfarben Blau und Ro\
t nicht auf 
dunklem Untergrund zu verwenden (schlechte Lesbarkeit und erhöhte Au\
genbelastung 
bei zu geringem Zeichenkontrast wären die Folge). 
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 beträgt 70d\
B (A) oder 
weniger. 
ACHTUNG: BEIM AUFSTELLEN DIESES GERÄTES DARAUF ACHTEN, DAß 
NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND. 
 
						

							
RETURN TO TOP OF THE PAGE
End-of-Life Disposal 
Your new monitor contains materials that can be recycled and reused. Spe\
cialized companies 
can recycle your product to increase the amount of reusable materials an\
d to minimize the 
amount to be disposed of. 
Please find out about the local regulations on how to dispose of your ol\
d monitor from your 
local Philips dealer. 
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance t\
o local-state and 
federal regulations.
For additional information on recycling contact www.eia.org (Consumer Education Initiative)RETURN TO TOP OF THE PAGE
Information for UK only
  WARNING - THIS APPLIANCE MUST BE 
EARTHED.
Important: 
This apparatus is supplied with an approved 
moulded 13A plug. To change a fuse in this 
type of plug proceed as follows: 
1. Remove fuse cover and fuse. 
2. Fit new fuse which should be a BS 1362 5A,
A.S.T.A. or BSI approved type. 
3. Refit the fuse cover. 
If the fitted plug is not suitable for your 
socket outlets, it should be cut off and an 
appropriate 3-pin plug fitted in its place. 
If the mains plug contains a fuse, this should 
have a value of 5A. If a plug without a fuse is 
used, the fuse at the distribution board 
should not be greater than 5A. 
Note: The severed plug must be destroyed to 
avoid a possible shock hazard should it be 
inserted into a 13A socket elsewhere. 
How to connect a plug 
The wires in the mains lead are coloured in 
accordance with the following code: