Philips 202el2sb User Manual

39
WHO IS COVERED?
You	must	have	proof	of	purchase	to	receive	
warranty	ser vice.	A	sales	receipt	or	other	
document showing that you purchased the 
product	is	considered	proof	of	purchase. 	Attach	it	
to this owner's manual and keep both nearby. 
WHAT IS COVERED?
Warranty coverage begins the day you buy your 
product. 	For	two	years	thereafter, 	all	par ts	will	be	
repaired	or	replaced,	and	labor	is	free.	After	two	
years from the day of purchase, you pay for the 
replacement or repair of all par...

40
Contact the Philips Customer Care Center phone 
number listed below for product assistance and 
procedures	for	ser vicing:	
Philips Customer Care Center 
(877) 835-1838 or (919) 573-7855
(In	U.S.A.,	Puer to	Rico	and	U.S. 	Virgin	Islands, 	all	
implied warranties, including implied warranties 
of merchantability and fitness for a par ticular 
purpose, are limited in duration to the duration 
of this express warranty. But, because some states 
do not allow limitations on how long an implied 
warranty...

41
Your International Guarantee
Dear Customer,
Thank you for purchasing this Philips product 
which has been designed and manufactured to the 
highest quality standards. 
If, unfor tunately, something should go wrong with 
this product Philips guarantees free of charge labor 
and replacement par ts irrespective of the countr y 
where it is repaired during a period of 12 months 
from date of purchase. This international Philips 
guarantee complements the existing national 
guarantee obligations to you of...

42
7.1 Troubleshooting
This page deals with problems that can be 
corrected by a user. If the problem still persists 
after you have tried these solutions, contact Philips 
customer ser vice representative.
 Common Problems
No Picture (Power LED not lit)
•	 Make	sure	the	power	cord	is	plugged	into		
  the power outlet and into the back of the  
 monitor. 
•	 First, 	ensure	that	the	power	button	on	the		
	 front	of	the	monitor	is	in	the	OFF	position, 		
 then press it to the ON position.
No Picture (Power...

43
Horizontal flicker appears
•	 Adjust	the	image	using	the	“Auto”	function		
	 in	OSD	Main	Controls. 	
•	 Eliminate	the	ver tical	bars	using	the	Phase/	
	 Clock	of	Setup	in	OSD	Main	Controls. 	It	is		
	 valid	only	in	VGA	mode.
Image appears blurred, indistinct or too dark
•	 Adjust	the	contrast	and	brightness	on	
 On-Screen Display.
An "after-image", "burn-in" or "ghost image" 
remains after the power has been turned off.
•	 Uninterrupted	display	of	still	or	static	images		
 over...

44
7.2 SmartControl Lite FAQs
Q1.  I change the monitor on a PC to a  
    different one and the SmartControl  
   Lite becomes un-usable,  what do I  
   do?
Ans.: Restar t your PC and see if Smar tControl  
   Lite can work. Otherwise, you will  
    need to remove and re-install Smar tControl   
   Lite to ensure proper driver is installed.
Q2.  The SmartControl Lite functions  
    worked well before, but it does not work  
   anymore, what can I do?
Ans.: If the following actions were executed,...

45
7.3 General FAQs
Q1:   When I install my monitor what should I  
   do if the screen shows 'Cannot display this   
   video mode'?
Ans.:	 Recommended	resolution	for	Philips	20": 		
   1600 x 900 @60Hz.
 • Unplug all cables, then connect your PC to  
   the monitor that you used previously. 
 • In	the	 Windows	Star t	Menu, 	select	Settings/	
   Control Panel. In the Control Panel Window,   
   select the Display icon. Inside the Display
   Control Panel, select the 'Settings' tab....

46
Q8:  Can I change the color setting of my  
   monitor?
Ans.:	 Yes,	you	can	change	your	color	setting		
    through OSD control as the following  
   procedures,
 • Press "OK" to show the OSD (On Screen  
   Display) menu
 • Press	"Down	 Arrow"	to	select	the	option		
   "Color" then press "OK" to enter color  
   setting, there are three settings as below.
   1.   Color Temperature; The six settings  
        are 5000K, 6500K, 7500K, 8200K, 9300K   
       and 11500K....

47
   "burn in", also known as "after-imaging" or  
   "ghost imaging", on your screen. "Burn-in", 
   "after-imaging", or "ghost imaging" is a 
   well-known phenomenon in LCD panel 
   technology. In most cases, the "burned in" or 
   "atter-imaging" or "ghost imaging" will 
   disappear gradually over a period of time 
   after the power has been switched off.
	 	 Always	activate	a	moving	screen	saver	
   program when you leave...

48
2010 © Koninklijke Philips Electronics N.V.   All r ights reser ved.
Philips and the Philips Shield Em blem are registered t radema rks of 
Koninklijke Philips Electronics N. V. and are used under license from 
Koninklijke Philips Elec t ronics N.V .
Specif ications are subject to change without notic e.
V er sion:  M2202E1T