Philips 19pfl3205h User Manual

							29
Rearrange channels
After you install channels, you can rearrange the 
order in which they appear.
1  When watching T V, press OK to display 
the channel grid.
2 Press  OPTIONS.
The channel options menu appears.   »
3 Press  to select [Reorder], then press 
OK.
4  Select the channel to rearrange, then 
press OK.
The selected channel is highlighted.   »
5 Press  to move the highlighted 
channel to the desired location, then 
press OK.
6 Press  OPTIONS.
  »[Done reordering] appears on the 
screen.
7 Press OK to confirm.
8 Press  BACK to exit the channel grid.
Rename channels
You can rename channels. The name appears 
when you select the channel.
1  When watching T V, press OK to display 
the channel grid.
2  Select the channel to rename.
3 Press  OPTIONS.
The channel options menu appears.   »
4 Press  to select [Rename channel], 
then press OK.
A text input box appears.   »
5 Press  to select characters.
6 Press OK to confirm each character.
7 Select [Done], then press OK to finish 
renaming channels.
Tip
Press   •[Aa] to change an uppercase let ter to a 
lowercase let ter and vice versa.
English
EN
 
						

							30
Test digital reception
You can check the quality and signal strength 
of digital channels. This allows you to reposition 
and test your antenna or satellite dish.
1 Press  MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel installation] > 
[Manual channel search].
3 Press  to enter the menu.
4 Press  to enter the frequency of 
the channel you want to test.
5 Press OK to confirm the frequency, then 
press OK again to confirm [Search].
6  When complete, select [Store] to store 
the frequency.
Note
If the signal quality and streng th is poor,   •reposition the aerial or satellite dish and retest.
If you still have problems with the reception   •of your digital broadcast, contact a specialised 
installer.
EN
 
						

							31
b  EXT 2 (Y Pb Pr and AUDIO L/R)
Analogue audio and video input from 
analogue or digital devices such as DVD 
players or game consoles.
 
c TV ANTENNA
Signal input from an antenna, cable or 
satellite.
 
TV ANTENNA
7 Connect devices
This section describes how to connect devices 
with different connectors. Examples are 
provided in the Quick Star t.
Note
You can use different types of connectors to   •connect a device to your TV.
Back connector
 
a HDMI 1
Digital audio and video input from high-
definition digital devices such as Blu-ray 
players.
  
Connections via DVI or VGA require an 
additional audio cable (see ‘Connect a 
computer’ on page 34).
English
EN
 
						

							32
Side connector
 
a COMMON INTERFACE
Slot for a Conditional Access Module 
(C AM).
 
d  EXT 1 (CVBS and RGB) 
Analogue audio and video input from 
analogue or digital devices such as DVD 
players or game consoles.
 
e SPDIF OUT
Digital audio output to home theatres 
and other digital audio systems.
 
f  PC IN (VGA and AUDIO)
Audio and video input from a computer.
 
g SERV. U
For sof tware update.
SPDIF OUT
VGA
PC AUDIO IN/ PC IN(AUDIO)
VGA
EN
 
						

							33
f  HDMI (Available only in 26 inch TV)
Digital audio and video input from high-
definition digital devices such as Blu-ray 
players.
  
b AUDIO L/R
Audio input from analogue devices 
connected to VIDEO.
 
c VIDEO
Composite video input from analogue 
devices such as VCRs.
 
d USB
Data input from USB storage devices.
 
e  (Headphone) 
Stereo audio output to headphones or 
earphones.
English
EN
 
						

							34
• HDMI cable and HDMI-DVI adaptor
 
• VGA cable
 
DVI
PC AUDIO IN/ PC IN(AUDIO)
VGA
PC AUDIO IN/ PC IN(AUDIO)
VGA
Connect a computer
Before you connect a computer to the TV
Set the screen refresh rate on your  • 
computer to 60Hz.
Select a suppor ted screen resolution on  • 
your computer.
Connect a computer with one of the 
following connectors:
Note
Connections via DVI or VGA require an   •additional audio cable.
• HDMI cable
 
• DVI - HDMI cable
 
DVI
PC AUDIO IN/ PC IN(AUDIO)
EN
 
						

							35
Access CAM services
1  Af ter inser ting and activating the CAM, 
press 
 MENU.
2 Press  to select [Setup] > 
[Features] > [Common interface].
Applications provided by the digital TV    »
ser vice operator appear on the screen.
Note
This menu option is available only if the CAM   •is inser ted and activated correctly.
Use a Conditional Access 
Module
A Conditional Access Module (CAM) is 
provided by digital TV ser vice operators to 
decode digital TV channels.
Note
Refer to the documentation from your ser vice   •operator on how to inser t a smar t card into 
the Conditional Access Module.
Insert and activate a CAM
Caution
Be sure to follow the instructions described   •below. Wrong inser tion of a CAM may 
damage both the CAM and your T V.
1  Switch off the T V and disconnect it from 
the power outlet.
2  Following the directions printed on the 
CAM, gently inser t the CAM into the 
COMMON INTERFACE at the side of 
the T V.
 
3  Push the CAM in as far as it will go.
4  Reconnect the T V to the power outlet.
5  Turn on the T V and wait for the CAM 
to be activated. This may take several 
minutes. Do not remove the CAM from 
the slot when in use — removing the 
CAM will deactivate digital ser vices.
English
EN
 
						

							36
Enable or disable EasyLink
Note
Do not enable Philips EasyLink if you do not   •intend to use it.
1 Press  MENU.
2 Press  to select [Setup] > 
[Installation] > [Preferences] > 
[EasyLink].
3 Select [On] or [Of f ].
Use one-touch play
1  Af ter enabling EasyLink, press play on 
your device. 
The TV automatically switches to the    »
correct source.
Use one-touch standby
1 Press  (Standby-On) on the T V ’s or 
device’s remote control. 
The TV and all connected HDMI    »
devices switch to standby.
Use Philips EasyLink
Your T V suppor ts Philips EasyLink, which 
uses the HDMI CEC (Consumer Electronics 
Control) protocol. EasyLink-compliant devices 
that are connected through HDMI connectors 
can be controlled by a single remote control. 
Note
The EasyLink-compliant device must be   •switched on and selected as the source.
Philips does not guarantee 10 0%   •interoperability with all HDMI CEC devices.
EasyLink features
One-touch play 
When you connect your T V to devices that 
suppor t one-touch play, you can control your 
T V and the devices with one remote control.
One-touch standby
When you connect your T V to devices that 
suppor t standby, you can use your T V remote 
control to put your T V and all connected 
HDMI devices in standby mode.
System audio control
When you connect your T V to HDMI 
CEC compliant devices, your TV can 
switch automatically to play audio from the 
connected device. 
To use one-touch audio, you must map the 
audio input from the connected device to 
your T V. 
You can use the remote control from the 
connected device to adjust the volume.
EN
 
						

							37
Use a Kensington lock
There is a Kensington security slot at the back 
of the TV. Prevent theft by looping a Kensington 
lock between the slot and a permanent object, 
such as a heavy table.
 
Set TV speakers to EasyLink mode
When you play content from an EasyLink 
compliant home theater, the T V speakers are 
automatically muted.
1  Enable one-touch play and one-touch 
standby between your Easylink compliant 
devices by following the instructions 
in the previous section (see ‘Enable or 
disable EasyLink ’ on page 36).
2 Press  MENU.
3 Press  to select [Setup] > [Sound] 
> [TV speakers] > [Auto EasyLink].
The TV speakers are turned off    »
automatically when content from an 
Easylink compliant system is detected.
4 Press  to select [Setup] > [Sound] 
> [TV speakers] > [On] to disable 
system audio control and enable the T V 
speakers.
Note
To mute the T V speakers, select   •[TV 
speakers] > [Of f ].
English
EN
 
						

							38
Multimedia
Suppor ted storage device: USB (Only  • 
FAT or FAT 32 USB storage devices are 
suppor ted) 
Suppor ted multimedia file formats: • 
Images: JPEG • 
Audio: MP3 • 
Note
Multimedia file names must not exceed 128   •characters. 
Tuner / Reception / 
Transmission
Aerial input: 75ohm coaxial (IEC75) • 
DVB: DVB Terrestrial, DVB -T MPEG4 • 
T V system: DVB COFDM 2K /8K; PAL I,  • 
B/G, D/K; SECAM B/G, D/K , L /L’ 
Video playback: NTSC , SECAM, PAL • 
Tuner Bands: Hyperband, S-channel, UHF,  • 
VHF
Remote control
Ty p e :  P F 0 1E 0 9 B • 
Batteries: 2 x A A A (LR03 type) • 
Power
Mains power: 220 -240V, 50Hz • 
Standby power: < 0.3 W • 
Ambient temperature: 5 to 40 degrees  • 
Celsius
8 Product 
information
Product information is subject to change 
without notice. For detailed product 
information, go to www.philips.com/suppor t.
Supported display resolutions
Computer formats
Resolution - refresh rate: • 
640 x 480 - 60Hz • 
800 x 600 - 60Hz • 
1024 x 768 - 60Hz • 
1280 x 720 -60Hz • 
1280 x 1024 - 60 Hz • 
1360 x 768 - 60Hz • 
Video formats
Resolution - refresh rate: • 
480i - 60Hz • 
480p - 60Hz • 
576i - 50Hz • 
576p - 50Hz • 
720p - 50Hz, 60Hz • 
1080i - 50Hz, 60Hz • 
1080p - 24Hz, 25Hz, 30Hz, 50Hz,  • 
60Hz.
EN