Philips 19pfl3205h User Manual

19
Automatically switch the TV on (on 
timer)
You can switch the T V to a specified channel 
at a specified time, from standby or power-on 
mode.
1 Press  MENU.
2 Press  to select [Setup] > 
[Features] > [On timer].
3 Press  to enter the [On timer] menu.
• [Activate]: Selects how of ten the T V 
is switched on.
• [Time]: Sets the time to switch on 
the T V.
• [Programme no.]: Selects the 
channel or the connected device.
4 Press  MENU to exit.
Tip
Select   •[On timer] > [Activate] > [Of f ] to 
disable...

20
Lock the TV for a specific time
1 Press .
2 Press  to select [Setup] > 
[Features] > [Lock after].
You are prompted to enter your PIN    »
code.
3  Enter your code using Numeric buttons.
4 Select [On].
The feature menu appears.   »
5 Select [Time], then press OK.
6  Enter the time with the Numeric buttons 
or the Navigation buttons.
7 Select [Done]. 
The TV automatically switches off at    »
the specific time.
Note
You have to enter your code ever y time you   •turn on your T V.
Switch the T V off and...

21
6 Select [On] to display subtitles always or 
[On during mute] to display subtitles only 
when audio is muted.
7 Press OK to enable subtitles.
8  Repeat this procedure to enable subtitles 
on each analogue channel.
Tip
Select   •[Subtitle mode] > [Of f ] to disable 
subtitles.
Enable subtitles on digital TV channels
1  When watching digital channels, press 
SUBTITLE. 
The    »[Subtitle mode] menu appears.
2 Select [On] to display subtitles always or 
[On during mute] to display subtitles only 
when...

22
View a slide show of your photos
1  When a full screen image of a photo is 
displayed, press OK.
A slide show begins from the selected    »
photo.
2  Press the following buttons to control the 
slide show:
• OK to pause the slide show.
• 
 to go back or move for ward to 
the next image.
• 
 BACK to stop the slide show. 
Change slide show settings
1  When viewing a slide show, press  
 OPTIONS.
The slide show options menu appears.   »
2 Press  to select one of the following.
• [Start Slideshow] / [Stop...

23
Disconnect a USB storage device
Caution
Follow this procedure to avoid damage to your   •USB storage device.
1 Press  BACK to exit the USB browser.
2  Wait for five seconds then disconnect the 
USB storage device.
Listen to digital radio 
channels
If digital broadcasting is available, digital radio 
channels are installed automatically during 
installation.
1  When watching T V, press OK to display 
the channel grid.
2 Press  OPTIONS.
3 Press  to select [Select list] > [Radio].
The radio channel grid...

24
Update using a USB device
Connect your USB storage device to the T V.
1  If the sof tware update screen does not 
appear automatically, select [Setup] > 
[Software update] > [Local updates] > 
[USB].
2 Press OK to update the T V sof tware 
manually.
3  Follow the on-screen instructions to 
complete the update.
Note
The T V restar ts af ter the sof tware update is   •complete.
Update using OAD
1  If using (DVB -T ) digital broadcast, your 
T V automatically receives sof tware 
updates. If you receive a...

25
Access decoder channel
You can map channels provided through a 
decoder or descrambler to your TV channel 
selection. In this way, you can select these 
channels by using the RC of your TV. The 
decoder or a descrambler must be connected 
to EXT1 (SCART). 
Set decoder channel
Map channels from a decoder or descrambler.
1 Press  MENU.
2 Select [Setup] > [Installation] > 
[Decoder].
3 Press  to enter [Decoder] menu.
4 Press  to select [Channel], then press 
 to enter.
5  Select one channel to map to the...

26
Start a TV demo
You can use demonstrations to better 
understand the features of your T V. Some 
demos are not available on cer tain models. 
Available demos are displayed in the menu list.
1 Press DEMO on the remote control.
2 Press  to select a demo and press OK 
to view it.
3 Press DEMO to exit.
Reset the TV to factory 
settings
You can restore the default picture and sound 
settings of your TV. The channel installation 
settings remain the same.
1 Press  MENU.
2 Select [Setup] > [Installation] >...

27
Step 3 Install channels
Automatically installs the available analogue 
and digital T V channels and digital radio 
channels.
1  From the channel installation guide 
screen, select [Full installation].
2 Press OK to confirm.
The TV star ts to search and store all    »
the available channels. 
3  When installation is complete, press OK 
to exit the installation menu.
Update the channel list
You can enable automatic update of channels 
when your T V is in standby mode. The 
channels stored in your TV are...

28
6 Press  BACK when the new channel is 
found.
7 Press  to select [Store as new 
channel] to store the new channel under 
a new channel number.
8 Press OK to enter [Store as new 
channel], then press OK.
9 Press  to return to the [Channel 
installation] menu.
Step 3 Fine-tune analogue channels
1 Press  MENU.
2 Press  to select [Setup] > 
[Installation] > [Channel installation] > 
[Analogue: manual install].
The    »[Analogue: manual install] menu 
appears.
3 Press  to select [Fine tune], then press...