Philips 196v3lsb User Manual

							
19
4.1 Resolution & Preset Modes
 Maximum Resolution
  1366 x 768 @ 60 Hz (analog input) 
 1366 x 768 @ 60 Hz (digital input)
 Recommended Resolution
  1366 x 768 @ 60 Hz (digital input)
H. freq (kHz)ResolutionV. freq (Hz)
31.47720 x 40070.09
31.47640 x 48059.94
37.50640 x 48075.00
37.88800 x 60060.32
46.88800 x 60075.00
48.361024 x 76860.00
60.021024 x 76875.03
47.711366 x 76859.79
 Note 
Please notice that your display works best at 
native resolution of 1366 x 768 @ 60Hz. For 
best display quality,please follow this resolution 
recommendation. 
 
00170011  
						

							
20
5. Power Management
If you have VESA DPM compliance display card 
or software installed in your PC, the monitor 
can automatically reduce its power consumption 
when not in use. If an input from a keyboard, 
mouse or other input device is detected, 
the monitor will 'wake up' automatically. The 
following table shows the power consumption 
and signaling of this automatic power saving 
feature: 
196V3LA: 
Power Management Definition
VESA Mode Video H-sync V-sync Power UsedLED Color 
Active ON YesYes17.91W (typ.)White
Sleep (Standby) OFFNoNo< 0.5W (typ.)White (blink) 
Switch OffOFF--< 0.5W (typ.)OFF
196V3L: 
Power Management Definition
VESA Mode Video H-sync V-sync Power UsedLED Color 
Active ON YesYes17.6W (typ.)White
Sleep (Standby) OFFNoNo< 0.5W (typ.)White (blink) 
Switch OffOFF--< 0.5W (typ.)OFF
The following setup is used to measure power 
consumption on this monitor.
•	Native resolution: 1366 x 768
•	Contrast: 50%
•	Brightness: 250 nits
•	Color temperature: 6500k with full white 
pattern
 Note
This data is subject to change without notice.

5. Power Management  
						

							
21
6. Regulatory Information
Lead-free Product
Lead free display promotes 
environmentally sound recover y 
and disposal of waste from electrical 
and electronic equipment. Toxic 
substances like Lead has been eliminated 
and compliance with European community’s 
stringent RoHs directive mandating restrictions 
on hazardous substances in electrical and 
electronic equipment have been adhered to 
in order to make Philips monitors safe to use 
throughout its life cycle.
Congratulations!
This display is designed for both you and the 
planet
The display you have just purchased 
carries the TCO Cer tified label. 
This ensures that your display is 
designed, manufactured and tested according to 
some of the strictest quality and environmental 
requirements in the world. This makes for a high 
performance product, designed with the user 
in focus that also minimizes the impact on the 
climate and our natural environment.
TCO Cer tified is a third par ty verified program, 
where ever y product model is tested by an 
accredited impar tial test laborator y. TCO 
Cer tified represents one of the toughest 
cer tifications for displays worldwide.
Some of the Usability features of the TCO 
Certified for displays:
•	Visual ergonomics for good image quality 
is tested to ensure top performance and 
reduce sight and strain problems. Impor tant 
parameters are luminance, contrast, 
resolution, black level, gamma cur ve, colour 
and luminance uniformity and colour 
rendering.
•	Products are tested according to rigorous 
safety standards at impar tial laboratories.
•	Electric and magnetic fields emissions as 
low as normal household background 
levels.
•	Low acoustic noise emissions (when 
applicable).
Some of the Environmental features of the 
TCO Certified for displays:  
•	The brand owner demonstrates corporate 
social responsibility and has a cer tified 
environmental management system (EMAS 
or ISO 14001).
•	Ver y low energy consumption both in on- 
and standby mode minimize climate impact.
•	Restrictions on chlorinated and brominated 
flame retardants, plasticizers, plastics and 
heavy metals such as cadmium, mercur y 
and lead (RoHS compliance).
•	Both product and product packaging is 
prepared for recycling.
•	The brand owner offers take-back options.
The requirements can be downloaded from our 
web site. The requirements included in this label 
have been developed by TCO Development in 
co-operation with scientists, exper ts, users as 
well as manufacturers all over the world. Since 
the end of the 1980s TCO has been involved 
in influencing the development of IT equipment 
in a more user-friendly direction. Our labeling 
system star ted with displays in 1992 and is 
now requested by users and IT-manufacturers 
all over the world. About 50% of all displays 
worldwide are TCO cer tified.
For more information, please visit:  
www.tcodevelopment.com
 TCOF1058 TCO Document, Ver. 2.1
Technology for you and the planet
(Only for selective models)
 
6. Regulatory Infomation  
						

							
22
EPEAT
(www.epeat.net)
The EPEAT (Electronic 
Product Environmental 
Assessment Tool) program 
evaluates computer 
desktops, laptops, and monitors based on 51 
environmental criteria developed through 
an extensive stakeholder consensus process 
suppor ted by US EPA.
EPEAT system helps purchasers in the public 
and private sectors evaluate, compare and 
select desktop computers, notebooks and 
monitors based on their environmental 
attributes. EPEAT also provides a clear and 
consistent set of performance criteria for the 
design of products, and provides an oppor tunity 
for manufacturers to secure market recognition 
for effor ts to reduce the environmental impact 
of its products.
Benefits of EPEAT
Reduce use of primar y materials 
Reduce use of toxic materials
Avoid the disposal of hazardous waste EPEAT’S 
requirement that all registered products meet 
ENERGY STAR’s energy efficiency specifications, 
means that these products will consume less 
energy throughout their life.
CE Declaration of Conformity
This product is in conformity with the following 
standards 
•	EN60950-1:2006 (Safety requirement of 
Information Technology Equipment).
•	EN55022:2006 (Radio Disturbance 
requirement of Information Technology 
Equipment).
•	EN55024:1998+A1:2001+A2:2003 
(Immunity requirement of Information 
Technology Equipment).
•	2006/95/EC (Low Voltage Directive).
•	2004/108/EC (EMC Directive).
•	2005/32/EC (EuP Directive, EC No. 
1275/2008 mplementing Directive 
for Standby and Off mode power 
consumption) and is produced by a 
manufacturing organization on ISO9000 
level.
The product also comply with the following 
standards 
•	ISO9241-307:2008 (Ergonomic 
requirement, Analysis and compliance test 
methods for electronic visual displays).
•	GS EK1-2000:2009 (GS mark requirement).
•	prEN50279:1998 (Low Frequency Electric 
and Magnetic fields for Visual Display).
•	MPR-II (MPR:1990:8/1990:10 Low 
Frequency Electric and Magnetic fields).
•	TCO CERTIFIED (Requirement for 
Environment Labeling of Ergonomics, 
Energy, Ecology and Emission, TCO: Swedish 
Confederation of Professional Employees) 
for TCO versions.
•	EN61000-3-2:2006+A1:2009+A2:2009 
(Limits for Harmonic Current Emission).
•	 EN61000-3-3:2008 (Limitation of Voltage 
Fluctuation and Flicker) following provisions 
of directives applicable.

6. Regulatory Infomation  
						

							
23
Energy Star Declaration
(www.energystar.gov)
As an ENERGY STAR® Par tner, we 
have determined that this product 
meets the ENERGY STAR® 
guidelines for energy efficiency.
 Note
We recommend you switch off the monitor 
when it is not in use for a long time.
Federal Communications Commission (FCC) 
Notice (U.S. Only)
 This equipment has been tested and found 
to comply with the limits for a Class B digital 
device, pursuant to Par t 15 of the FCC 
Rules. These limits are designed to provide 
reasonable protection against harmful 
interference in a residential installation. 
This equipment generates, uses and can 
radiate radio frequency energy and, if not 
installed and used in accordance with the 
instructions, may cause harmful interference 
to radio communications.  
 
However, there is no guarantee that 
interference will not occur in a par ticular 
installation. If this equipment does cause 
harmful interference to radio or television 
reception, which can be determined by 
turning the equipment off and on, the 
user is encouraged to tr y to correct 
the interference by one or more of the 
following measures: 
•	Reorient or relocate the receiving antenna.
•	Increase the separation between the 
equipment and receiver.
•	Connect the equipment into an outlet on 
a circuit different from that to which the 
receiver is connected.
•	Consult the dealer or an experienced 
radio/TV technician for help.
  Changes or modifications not expressly 
approved by the par ty responsible for 
compliance could void the user's authority 
to operate the equipment.
Use only RF shielded cable that was supplied 
with the monitor when connecting this monitor 
to a computer device. 
To prevent damage which may result in fire or 
shock hazard, do not expose this appliance to 
rain or excessive moisture. 
THIS CLASS B DIGITAL APPARATUS MEETS 
ALL REQUIREMENTS OF THE CANADIAN 
INTERFERENCE-CAUSING EQUIPMENT 
REGULATIONS.
FCC Declaration of Conformity
Declaration of Conformity for Products Marked 
with FCC Logo, 
United States Only
This device complies with Par t 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any 
interference received, including interference that 
may cause undesired operation. 
Commission Federale de la Communication 
(FCC Declaration)
 Cet équipement a été testé et déclaré 
conforme auxlimites des appareils 
numériques de class B,aux termes de 
l'ar ticle 15 Des règles de la FCC . Ces 
limites sont conçues de façon à fourir 
une  protection raisonnable contre les 
interférences nuisibles dans le cadre d'une 
installation résidentielle.  
 
CET appareil produit, utilise et peut émettre 
des hyperfréquences qui, si l'appareil n'est 
pas installé et utilisé selon les consignes 
données, peuvent causer des interférences 
nuisibles aux communications radio.  
 
6. Regulatory Infomation  
						

							
24
Cependant, rien ne peut garantir l'absence 
d'interférences dans le cadre d'une 
installation par ticulière. Si cet appareil est 
la cause d'interférences nuisibles pour 
la réception des signaux de radio ou de 
télévision, ce qui peut être décelé en 
fermant l'équipement, puis en le remettant 
en fonction, l'utilisateur pourrait essayer de 
corriger la situation en prenant les mesures 
suivantes:
•	Réorienter ou déplacer l’antenne de 
réception.
•	Augmenter la distance entre l’équipement 
et le récepteur.
•	Brancher l’équipement sur un autre circuit 
que celui utilisé par le récepteur.
•	Demander l’aide du marchand ou d’un 
technicien chevronné en radio/télévision.
 Toutes modifications n'ayant pas reçu 
l'approbation des ser vices compétents 
en matière de conformité est susceptible 
d'interdire à l'utilisateur l'usage du présent 
équipement.
N'utiliser que des câbles RF armés pour 
les connections avec des ordinateurs ou 
périphériques. 
CET APPAREIL NUMERIQUE DE LA CLASSE 
B RESPECTE TOUTES LES EXIGENCES DU 
REGLEMENT SUR LE MATERIEL BROUILLEUR 
DU CANADA. 
EN 55022 Compliance (Czech Republic Only)
Polish Center for Testing and Certification 
Notice
The equipment should draw power from a 
socket with an attached protection circuit (a 
three-prong socket). All equipment that works 
together (computer, monitor, printer, and so on) 
should have the same power supply source.
The phasing conductor of the room's electrical 
installation should have a reser ve shor t-circuit 
protection device in the form of a fuse with a 
nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the 
power supply cable must be removed from the 
power supply socket, which should be located 
near the equipment and easily accessible.
A protection mark "B" confirms that the 
equipment is in compliance with the protection 
usage requirements of standards PN-93/T-42107 
and PN-89/E-06251.

6. Regulatory Infomation  
						

							
25
North Europe (Nordic Countries) Information
Placering/Ventilation 
VARNING:
FÖRSÄKRA  DIG  OM ATT  HUVUDBRYTARE 
OCH  UTTAG  ÄR  LÄTÅTKOMLIGA,  NÄR 
DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation 
ADVARSEL: 
S Ø R G   V E D   P L A C E R I N G E N   F O R ,  AT 
NETLEDNINGENS  STIK  OG  STIKKONTAKT 
ER NEMT TILGÆNGELIGE. 
Paikka/Ilmankier to 
VAROITUS: 
SIJOITA  LAITE  SITEN,  ETTÄ VERKKOJOHTO 
V O I D A A N   TA R V I T TA E S S A   H E L P O S T I 
IRROTTAA PISTORASIASTA. 
Plassering/Ventilasjon 
ADVARSEL: 
NÅR  DETTE  UTSTYRET  PLASSERES,  MÅ 
D U   PA S S E   P Å   AT   KO N TA K T E N E   F O R 
STØMTILFØRSEL ER LETTE Å NÅ.
BSMI Notice (Taiwan Only)
Ergonomie Hinweis (nur Deutschland)
Der von uns geliefer te Farbmonitor entspricht 
den in der "Verordnung über den Schutz vor 
Schäden durch Röntgenstrahlen" festgelegten 
Vorschriften. 
Auf der Rückwand des Gerätes befindet sich 
ein Aufkleber, der auf die Unbedenklichkeit der 
Inbetriebnahme hinweist, da die Vorschriften 
über die Bauar t von Störstrahlern nach Anlage 
III	 ¤ 	 5 	 Abs. 	 4 	 der 	 Röntgenverordnung 	 erfüllt 	 sind. 	
Damit Ihr Monitor immer den in der Zulassung 
geforder ten Wer ten entspricht, ist darauf zu 
achten, daß 
1. Reparaturen nur durch Fachpersonal 
durchgeführ t werden. 
2.  nur original-Ersatzteile verwendet werden. 
3.  bei Ersatz der Bildröhre nur eine 
bauar tgleiche eingebaut wird. 
Aus  ergonomischen  Gründen  wird  empfohlen, d i e   G r u n d f a r b e n   B l a u   u n d   R o t   n i c h t   a u f dunklem  Untergrund  zu  verwenden  (schlechte Lesbarkeit  und  erhöhte Augenbelastung  bei  zu geringem Zeichenkontrast wären die Folge). Der  arbeitsplatzbezogene  Schalldr uckpegel n a c h   D I N   4 5   6 3 5   b e t r ä g t   7 0 d B   ( A )   o d e r weniger. 
 ACHTUNG: BEIM AUFSTELLEN 
DIESES GERÄTES DARAUF ACHTEN, DAß NETZSTECKER UND NETZKABELANSCHLUß LEICHT ZUGÄNGLICH SIND. 
 
6. Regulatory Infomation  
						

							
26
China RoHS 
The People's Republic of China released a 
regulation called "Management Methods for 
Controlling Pollution by Electronic Information 
Products" or commonly referred to as China 
RoHS. All products including CRT and Monitor 
which are produced and sold for China market 
have to meet China RoHS request.
 环保使用期限 
此 标 识 指 期 限 ( 十 年 ) , 电 子 信 息 产 品 中 含 有
的 有 毒 有 害 物 质 或 元 素 在 正 常 使 用 的 条 件
下不会发生外泄或突变,  电子信息产品用户
使 用 该 电 子 信 息 产 品 不 会 对 环 境 造 成 严 重
污染或对其人身、  财产造成严重损害的期
限．
《废弃电器电子产品回收处理管理条例》提示性说明
为了更好地关爱及保护地球，当用户不再需要此产品或产品寿命终止时，请遵守国家废弃电器电子产品回收处理相关法律法规，将其交给当地具有 国 家 认 可 的 回 收 处 理 资 质 的 厂 商 进 行 回 收 处
理。

6. Regulatory Infomation  
						

							
27
7. Customer care and 
warrant
7.1  Philips’ Flat Panel Monitors Pixel 
Defect Policy
Philips strives to deliver the highest quality 
products. We use some of the industr y's most 
advanced manufacturing processes and practice 
stringent quality control. However, pixel or 
sub pixel defects on the TFT Monitor panels 
used in flat panel monitors are sometimes 
unavoidable. No manufacturer can guarantee 
that all panels will be free from pixel defects, 
but Philips guarantees that any monitor with an 
unacceptable number of defects will be repaired 
or replaced under warranty. This notice explains 
the different types of pixel defects and defines 
acceptable defect levels for each type. In order 
to qualify for repair or replacement under 
warranty, the number of pixel defects on a TFT 
Monitor panel must exceed these acceptable 
levels. For example, no more than 0.0004% of 
the sub pixels on a monitor may be defective. 
Fur thermore, Philips sets even higher quality 
standards for cer tain types or combinations 
of pixel defects that are more noticeable than 
others. This policy is valid worldwide.
Pixels and Sub pixels
A pixel, or picture element, is composed of 
three sub pixels in the primar y colors of red, 
green and blue. Many pixels together form an 
image. When all sub pixels of a pixel are lit, the 
three colored sub pixels together appear as a 
single white pixel. When all are dark, the three 
colored sub pixels together appear as a single 
black pixel. Other combinations of lit and dark 
sub pixels appear as single pixels of other colors.
Types of Pixel Defects 
Pixel and sub pixel defects appear on the screen 
in different ways. There are two categories of 
pixel defects and several types of sub pixel 
defects within each categor y. 
Bright Dot Defects
Bright dot defects appear as pixels or sub pixels 
that are always lit or 'on'. That is, a bright dot is 
a sub-pixel that stands out on the screen when 
the monitor displays a dark pattern. There are 
the types of bright dot defects.
One lit red, green or blue sub pixel.
Two adjacent lit sub pixels:
-  Red + Blue = Purple
-   Red + Green = Yellow
-   Green + Blue = Cyan (Light Blue)
Three adjacent lit sub pixels (one white pixel).
 
7. Customer care and warranty  
						

							
28
 Note
A red or blue bright dot must be more than 50 
percent brighter than neighboring dots while 
a green bright dot is 30 percent brighter than 
neighboring dots.
Black Dot Defects 
Black dot defects appear as pixels or sub pixels 
that are always dark or 'off'. That is, a dark dot is 
a sub-pixel that stands out on the screen when 
the monitor displays a light pattern. These are 
the types of black dot defects.
Proximity of Pixel Defects 
Because pixel and sub pixels defects of the 
same type that are near to one another may be 
more noticeable, Philips also specifies tolerances 
for the proximity of pixel defects.
Pixel Defect Tolerances
In order to qualify for repair or replacement 
due to pixel defects during the warranty period, 
a TFT Monitor panel in a Philips flat panel 
monitor must have pixel or sub pixel defects 
exceeding the tolerances listed in the following 
tables.
BRIGHT DOT DEFECTSACCEPTABLE LEVEL
1 lit subpixel3
2 adjacent lit subpixels1
3 adjacent lit subpixels (one white pixel)0
Distance between two bright dot defects*>15mm
Total bright dot defects of all types3
BLACK DOT DEFECTSACCEPTABLE LEVEL
1 dark subpixel5 or fewer
2 adjacent dark subpixels2 or fewer
3 adjacent dark subpixels0
Distance between two black dot defects*>15mm
Total black dot defects of all types5 or fewer
TOTAL DOT DEFECTSACCEPTABLE LEVEL
Total bright or black dot defects of all types5 or fewer
 Note
1.   1 or 2 adjacent sub pixel defects = 1 dot defect
2.  This monitor is ISO9241-307 compliant (ISO9241-307: Ergonomic requirement,analysis and 
compliance test methods for electronic visual displays)

7. Customer care and warranty