Para Single Actio LDA PXT Instruction Manual

							
This will retract the two small tabs at the rear of  the extension 
which keep  it in place. Gently increase the pressure on the 
release lever until some resistance is felt.
CAUTION:
  Do not apply excessive pressure to the release lever 
or it may break off. 
CAUTION:  The spring and follower  are compressed in the 
magazine. Care should be taken during this step to prevent 
them from flying out.
STEP  4:   While maintaining 
the gentle pressure on 
the release  lever, begin 
to rotate the magazine 
extension downward to 
release it from the metal 
magazine body. Release 
 
pressure from the lever 
as soon as the two small 
tabs at the top rear of  
the extension clear the 
magazine body. The extension can now be removed by easing 
it slightly rearward to release the round tab at the front. The 
spring and magazine follower can now be removed through 
the opening at the bottom of  the metal magazine body. As you 
remove it, note which end faces the front.
CLEANING
CAUTION:  Do not attempt to remove the follower from the 
spring.
Wipe the outside of  the magazine with a rag. Insert a dry rag 
through the opening  at the bottom of  the metal  magazine 
body and  remove all residue from the inside. Do the same 
from the smaller opening at the top.
DISASSEMBLY
STEP 1:  Remove all  
ammunition from the 
magazine. Firmly  grasp 
the metal  magazine 
body in one hand and 
with the other hand 
grip  the magazine’s base 
plate. Use your thumb 
to slightly raise the 
 
slotted tab at the rear 
of  the base plate. 
CAUTION:
  Lift the  
slotted tab only enough 
to clear the rear of  the 
magazine extension.
S
TEP 2:  Slide the base plate 
toward the front of  the 
magazine to remove it.
S
TEP  3:  While  holding the  
magazine in one hand, 
use  the index finger of  
the other hand to gently  apply a small amount of   pressure to 
the release  lever at the bottom of  the magazine extension.
36
DISASSEMBLY, CLEANING & REASSEMBLY OF 
10-ROUND PARA-ORDNANCE MAGAZINE
METAL 
MAGAZINE 
BODYSLOTTED 
TAB ON 
BASE PLATE
MAGAZINE EXTENSION(REAR)
RELEASE LEVER
TWO SMALL 
TABS (REAR)
BEFORE PROCEEDING MAKE SURE  
YOU ARE WEARING SAFETY GLASSES 
 
AND KEEP THE MAGAZINE 
 
POINTED AWAY FROM YOUR FACE.
37
TWO SMALL 
TABS (REAR)
ROUND TAB
 
(FRONT) 
						

							
Clean all residue from the spring and from the magazine  
follower.
CAUTION:
  Do not apply oil to any part or lubricate any part  
of  the magazine.
REASSEMBLY
STEP 1:  Insert the spring and follower into the  opening at the  
bottom of  the metal magazine body
CAUTION:
  Make sure that the rounded top edge of  the  
follower is at the front of  the magazine.
Position the bottom of  the spring around the four posts on 
the magazine extension. Then, gently compress the spring with 
the magazine extension so that it is fully contained inside the 
magazine body.  Engage the round tab at the top front of  the 
magazine extension in the small hole at the front of  the 
 
magazine body.
While still holding the 
spring compressed, 
gently apply a 
tiny 
amount of  rearward 
pressure to the lever 
at the bottom  of  the 
extension until some 
resistance is felt.
Then, rotate the rear 
of  the extension 
upwards so it engages the magazine body. Continue 
rotating 
until the two small tabs are fully engaged.
Release the pressure from the lever at the bottom of  
the 
extension. The magazine extension is now locked in place.
38
TRANSPORTATION AND STORAGE
When transporting your firearm to and from shooting activities, 
keep it unloaded and obey all laws relating to the transportation 
of  firearms in your area.
When storing your firearm, store it securely and keep it  separated 
from ammunition, under lock and key, and out of  the sight and 
reach of  children and other inexperienced persons.
N
OTE:   Protect your firearms from theft.
S
TEP 2: 
With your index 
finger, gently depress 
the lever at 
the  
bottom of  the  extension.  This will 
allow you to replace t he base plate without 
breaking the tab.
 While holding the lever in a depressed position, begin to 
replace the base plate by sliding it rearward from the  front of  
the extension. Be sure that the base plate engages the two rails 
on the sides of  the extension.
  Continue to slide the base plate towards the rear until a  click 
is heard, indicating that the slotted tab at the rear of   the base 
plate has passed over the rear edge of  the extension,  locking it 
in place.
  Reassembly is now complete.
These instructions apply to all 10-round magazines for  
Para-Ordnance PXT handguns except the Warthog. In  
order to clean  and disassemble Warthog (Model No. 
WHX1045R and NHX1045N) magazines, follow the 
 
instructions on page 34 for the Hi-Cap magazine.
39 
						

							
DO NOT STORE your pistol in anything which will attract  
moisture, e.g., leather or heavy cloth, and do not store it in an  
air-tight container or with a plug inserted in the barrel for these 
are factors that can contribute to corrosion.
EXTENDED STORAGE requires that the internal mechanisms 
are well oiled with an acid-free lubricating oil or preservative 
 
while external mechanisms (receiver, barrel, etc.) should be  
coated with an anti-rust oil.
COLD CLIMATE STORAGE requires that you make use of  an 
oil which will not congeal at low temperatures. USE SPARINGLY.
BEFORE USING YOUR FIREARM AGAIN, BE SURE 
TO CLEAN IT.
40
Para-Ordnance acknowledges its obligations under implied  
warranty legislation, with respect to the sale of  consumer goods, 
that may be in force in jurisdictions where its products are sold. 
Due to differences in the extent and interpretation of  such 
 
statutes, and also on the basis of  the Magnusson-Moss Warranty 
Act of  the United States of  America, Para-Ordnance has elected 
not to offer any written or express warranty on its product line 
and you are advised to consult existing legislation in your country, 
state or province with regard to any implied warranty rights you 
may have under such laws. However, Para-Ordnance is strongly 
committed to properly servicing its products, as it has over the 
years, and in place of  an express or written warranty it will 
 
provide all necessary service for its pistols purchased after  
January 1, 2001 free of  charge to the original purchaser only, 
where adjustment or repair is required due to some defect in 
materials or workmanship.
N
OTE:  Different remedies may be available to you in different 
jurisdictions.
WARRANTY INFORMATION
41
WHEN AUTHORIZED TO SHIP YOUR FIREARM FOR ADJUST MENT 
OR REPAIR, PLEASE CAREFULLY NOTE THE FOLLOWING:
1.  A detailed, written explanation of  your problem should  
accompany the firearm being shipped for service or repair. 
Include model name, serial number and your return address 
(day telephone number optional). Also include a copy of  your 
original proof  of  purchase.
2.  All firearms should be shipped by common carrier (e.g., UPS),  prepaid (we will not accept collect shipments) and insured for 
their full value. It is illegal for unlicensed individuals to ship 
handguns through the mail.
3.  Due to the vast number of  laws governing the transfer and  transportation of  firearms, it is strongly recommended that 
your firearm be shipped through a licensed dealer who will 
also accept delivery on your behalf  when the pistol is returned. 
The shipment should be accompanied by a signed copy of  the 
dealer’s license.
4.  DO NOT include holsters, custom grips or other accessories  when shipping your firearm for service.
SERVICE AND REPAIR
MAKE SURE THAT THE MAGAZINE AND   
PISTOL ARE UNLOADED. DO NOT SHIP ANY  CARTRIDGES WITH A FIREARM.
If  any problem or question should arise with regard to the  
performance of  your firearm, please contact us, by mail or  
telephone, and fully describe all circumstances involved. This will 
allow us to determine the best way to handle your problem. If  
authorized factory service is deemed necessary, you will be given a 
return authorization number and shipping instructions. 
						

							
42
NOTE:  PARA-ORDNANCE HAS CAREFULLY PACKAGED THIS 
PRODUCT PRIOR TO SHIPMENT FROM THE FACTORY. 
PLEASE EXAMINE IT CAREFULLY AT TIME OF PURCHASE 
TO ENSURE IT IS UNDAMAGED.
PARA- ORDNANCE SHALL NOT BE RESPONSIBLE IN ANY MANNER WHATSOEVER FOR INJURY, DEATH, OR DAMAGE 
TO PROPERTY AS A RESULT OF THE INTENTIONAL OR 
ACCIDENTAL DISCHARGE OF  THIS FIREARM, OR FROM 
ITS PROPER FUNCTION WHEN THE PISTOL IS USED 
FOR PURPOSES FOR WHICH IT WAS NOT DESIGNED. 
FURTHERMORE, PARA-ORDNANCE SHALL NOT BE 
RESPONSIBLE FOR ANY CLAIMS THAT MAY ARISE 
AS A RESULT OF, WHETHER IN WHOLE OR IN PART, 
IMPROPER OR CARELESS HANDLING, UNAUTHORIZED 
MODIFICATIONS, USE OF IMPROPER AMMUNITION 
(WRONG CALIBER, DEFECTIVE, HAND LOADED, OR 
RELOADED CARTRIDGES) THAT IS NOT ORIGINAL HIGH 
QUALITY COMMERCIALLY MANUFACTURED  AND IN 
GOOD CONDITION, ABUSE, NEGLECT, CORROSION, OR 
OTHER INFLUENCES BEYOND OUR IMMEDIATE AND 
DIRECT CONTROL. UNDER NO CIRCUMSTANCES SHALL 
PARA-ORDNANCE BE RESPONSIBLE FOR INCIDENTAL
 
OR CONSEQUENTIAL DAMAGES, SUCH AS LOSS OF USE 
OF PROPERTY, LOSS OF EARNINGS OR PROFITS, OR ANY 
OTHER COMMERCIAL LOSS.
NOTE:  DIFFERENT REMEDIES MAY BE AVAILABLE TO YOU 
IN DIFFERENT JURISDICTIONS.
LIMITS OF LIABILITY
5.  DO NOT indicate the nature of  the contents on the package  or use the “Para-Ordnance” name to address the shipment.
6.  DO include the return authorization number on the outside of   the package.
43
For Para-Ordnance replacement parts please contact your local 
dealer who should be able to assist you. Alternatively, you can also 
contact the Para-Ordnance Parts Department by mail or phone, 
for up-to-date information on the names and locations of  our 
Authorized Service Centers as well as current parts prices.
PARTS AVAILABLE FOR SALE SHOULD BE INSTALLED 
AT A PARA-ORDNANCE AUTHORIZED SERVICE 
CENTER. OTHERWISE, IT IS THE PURCHASER’S TOTAL 
RESPONSIBILITY TO MAKE ABSOLUTELY CERTAIN 
THAT ANY PARTS FITTED AND INSTALLED ARE OF THE 
CORRECT TYPE AND THE WORK IS PERFORMED BY A 
COMPETENT PERSON.
SPARE PARTS
PARA-ORDNANCE WILL NOT BE RESPONSIBLE  
FOR ANY UNAUTHORIZED ALTERATIONS 
 
PERFORMED, UNAUTHORIZED ATTACHMENTS 
FITTED OR UNAUTHORIZED PARTS 
 
USED 0N THIS PRODUCT.
NOTES: 
						

							
44
S-A SINGLE STACK PARTS ILLUSTRATIONSINGLE-ACTION, SINGLE STACK PARTS LIST
45
��
��
��
��
��
���
��
���
���
���
��
�
�
�
�
�
�
��
��
��
��
���
��
��
��
��
��
�� ����
��
����
��
��
��
��
��
��
��
��
��
��
��
����
��
��
��
������������
���
��
RECOIL SPRING ASSEMBLY
  1.  BARREL
  2.  BARREL LINK
  3.  BARREL LINK PIN
  4.  DISCONNECTOR
  5  EJECTOR
  6.  EJECTOR PIN
    
7A. EXTRACTOR CLAW
    7B. EXTRACTOR BODY
    7C.  EXTRACTOR PLUNGER
    7D. EXTRACTOR SPRING
  8.  FIRING PIN
  9.  FIRING PIN PLUNGER
 10.  FIRING PIN SPRING
 11.  FIRING PIN STOP
 12.  FRONT SIGHT
 13.  FIXED REAR SIGHT
 14.  GRIP SAFETY
 15.  GRIP (SET)
  16A. GRIP SCREW (4)
  16B.  GRIP SCREW LOCKING 
RINGS
  16C.  GRIP SCREW BUSHING
 17.  HAMMER
 18.  HAMMER PIN
 19.  HAMMER STRUT
 20.  HAMMER STRUT PIN
 21.  MAGAZINE ASSEMBLY
 22.  MAGAZINE CATCH
 23.  MAGAZINE CATCH LOCK
 24.  MAGAZINE CATCH
 SPRING
 25.  MAGAZINE FOLLOWER
 26.  MAGAZINE SPRING 
 
(NOT SHOWN)
 27 .  MAIN SPRING
 28.  MAIN SPRING CAP
 29.  MAIN SPRING CAP PIN
 30.  MAIN SPRING HOUSING
 
(FLAT)
 31.  MAIN SPRING HOUSING
 PIN
 32.  MAIN SPRING HOUSING 
PIN RETAINER
 33.  PLUNGER LEVER
 34.  PLUNGER SPRING
 35.  PLUNGER SPRING F/P
 36.  RECEIVER
 37A.  RECOIL SPRING OUTER
 37B.  RECOIL SPRING 
INNER
 38A.  RECOIL SPRING GUIDE 
ROD INNER
 38B.  RECOIL SPRING 
GUIDE PLATE 38C.  RECOIL SPRING GUIDE 
ROD OUTER
 39.  RECOIL SPRING  PLUG
 40.  SLIDE LOCK SAFETY
 41.  SAFETY LOCK PLUNGER
 42.  SEAR
 43.  SEAR PIN
 44.  SEAR SPRING
 45.  SLIDE
 46 .  SLIDE STOP
 47.  SLIDE STOP PLUNGER
 48.  TRIGGER ASSEMBLY
 49.  TRIGGER BAR LEVER
 50.  OVER TRAVEL SCREW  (LIMITED ONLY) 
						

							
46
SINGLE-ACTION, HI-CAP PARTS ILLUSTRATION
47
SINGLE-ACTION, HI-CAP PARTS LIST
��
��
��
��
��
���
��
���������
���
��
�
��
�
�
�
�
�
�
��
��
��
��
���
���
��
��
����
��
��
����
��
����
��
��
��
��
��
��
��
���
��
��
��
��
��
��
����
��
��
��
���
 1.  BARREL
  2.  BARREL LINK
  3.  BARREL LINK PIN
  4.  DISCONNECTOR
  5.  EJECTOR
  6.  EJECTOR PIN
    
7A. EXTRACTOR CLAW
    7B. EXTRACTOR BODY
    7C.  EXTRACTOR PLUNGER
    7D. EXTRACTOR SPRING
  8.  FIRING PIN
  9.  FIRING PIN PLUNGER
 10.  FIRING PIN SPRING
 11.  FIRING PIN STOP
  12.  FRONT SIGHT
 13.  FIXED REAR SIGHT
 14.  GRIP SAFETY
  15.  GRIP (SET)  16A. GRIP SCREW (4)  16B.  GRIP SCREW LOCKING RINGS 17 .  HAMMER 18.  HAMMER PIN 19.  HAMMER STRUT
 20.  HAMMER STRUT PIN
  21.  MAGAZINE ASSEMBLY 22.  MAGAZINE CATCH 23.  MAGAZINE CATCH LOCK
 24.  MAGAZINE CATCH SPRING
 25.  MAGAZINE FLOOR  PLATE
 26.  MAGAZINE FOLLOWER  27.  MAGAZINE SPRING 
 
(NOT SHOWN)
 28.  MAIN SPRING
 29.  MAIN SPRING CAP
 30.  MAIN SPRING CAP PIN
 31.  MAIN SPRING HOUSING
 
(FLAT)
 32.  MAIN SPRING HOUSING
 PIN
 33.  MAIN SPRING HOUSING 
PIN RETAINER
 34.  PLUNGER LEVER
 35.  PLUNGER SPRING
 36.  PLUNGER SPRING F/P
 37A.  RECOIL SPRING OUTER
 37B.  RECOIL SPRING 
INNER
 38A.  RECOIL SPRING GUIDE 
ROD INNER
 38B.  RECOIL SPRING 
GUIDE PLATE
 38C.  RECOIL SPRING GUIDE 
ROD OUTER
 39.  RECOIL SPRING  PLUG
 40.  RECEIVER
 41.  SLIDE LOCK SAFETY
 42.  SAFETY LOCK PLUNGER
 43.  SEAR
 44.  SEAR PIN
 45.  SEAR SPRING
 46.  SLIDE
 47.  SLIDE STOP
 48.  SLIDE STOP PLUNGER
 49.  TRIGGER ASSEMBLY
 50.  TRIGGER BAR LEVER
 51.  OVER TRAVEL SCREW  (LIMITED ONLY)
RECOIL SPRING ASSEMBLY 
						

							
LDA SINGLE STACK PARTS ILLUSTRATIONLDA SINGLE STACK PARTS LIST
4948
��
���
��
���
������
��
��
��
��
��
��
��
�����
��
�
�
�
�
�
���
���
��
��
��
��
��
����
��
��
��
��
��
��
��
��
��
���
��
����
����
��
���
��
���
��
��
����
��
��
��
��
���
������
��
   1. BARREL 2. BARREL LINK 3. BARREL LINK PIN 4. DRAWBAR  5. EJECTOR 6. EJECTOR PIN 7A. EXTRACTOR CLAW 7B. EXTRACTOR BODY 7C. EXTRACTOR PLUNGER 7D. EXTRACTOR SPRING 8. FIRING PIN 9. FIRING PIN PLUNGER
10. FIRING PIN SPRING
11. FIRING PIN STOP
12. FRONT SIGHT
13. REAR SIGHT 
14. GRIP SAFETY B/SF
15. GRIP (SET)
16A. GRIP SCREW (4)
16B.  GRIP SCREW LOCKING 
RINGS
16C.  GRIP SCREW BUSHING
17 . HAMMER (SPURLESS) 
18. HAMMER PIN
19 . HAMMER STRUT20. COCKING CAM PIN
21. MAGAZINE ASSEMBLY
22. MAGAZINE CATCH
23. MAGAZINE CATCH LOCK
24.  MAGAZINE CATCH SPRING
25. MAGAZINE FOLLOWER
26.  MAGAZINE SPRING 
 
(NOT SHOWN)
27 . MAIN SPRING28. MAIN SPRING CAP29. MAIN SPRING CAP PIN 30.  MAIN SPRING HOUSING
 
(FLAT)
31.   MAIN SPRING HOUSING PIN
32.  MAIN SPRING HOUSING
 
PIN RETAINER
33. PLUNGER LEVER
34. PLUNGER SPRING
35. PLUNGER SPRING F/P
36. RECEIVER
37A. RECOIL SPRING OUTER
37B. RECOIL SPRING INNER
38A .   RECOIL SPRING GUIDE 
ROD INNER38B .  RECOIL SPRING GUIDE PLATE38C .  RECOIL SPRING GUIDE 
ROD OUTER
39 .  RECOIL SPRING PLUG 
40. SLIDE LOCK SAFETY
41. SAFETY LOCK PLUNGER
42. SEAR
43. SEAR PIN
44. SEAR SPRING
45. SLIDE46 . SLIDE STOP47. SLIDE STOP PLUNGER48. TRIGGER49. STRADDLE
50. TRIGGER PIN
51. TRIGGER RETURN SPRING
52. COCKING CAM
53. HAMMER RETURN SPRING
54. SAFETY LOCK LEVER
55. GRIP SAFETY LEVER
56 .  DRAWBAR PLATFORM SPRING
57 . HAMMER ASSEMBLY PIN
RECOIL SPRING 
ASSEMBLY 
						

							
5051
LDA HIGH CAPACITY PARTS ILLUSTRATIONLDA HIGH CAPACITY PARTS LIST
�����
���
��
��
������
��
��
��
��
��
��
��
���
��
��
�
�
�
�
�
� ��
����
��
��
���
��
��
��
��
����
��
��
��
��
��
��
��
��
��
��
���
��
����
����
��
��
�� ��
��
��
��
��
���������
��
 
1. BARREL
  2. BARREL LINK
  3. BARREL LINK PIN
  4. DRAWBAR
  5. EJECTOR
  6. EJECTOR PIN
    
7A. EXTRACTOR CLAW
    7B. EXTRACTOR BODY
    7C. EXTRACTOR  PLUNGER
    7D. EXTRACTOR SPRING
  8. FIRING PIN
 9. FIRING PIN PLUNGER
10. FIRING PIN SPRING
11. FIRING PIN STOP
12. FRONT SIGHT
13. FIXED REAR SIGHT
14. GRIP SAFETY
15. GRIP (SET)
16A. GRIP SCREW (4)
16B.  GRIP SCREW
 
LOCKING RINGS
17. HAMMER (SPURLESS)
18. HAMMER PIN
19 . HAMMER STRUT20. COCKING CAM PIN21. MAGAZINE ASSEMBLY22. MAGAZINE CATCH23. MAGAZINE CATCH LOCK24.  MAGAZINE CATCH SPRING
25.  MAGAZINE FLOOR PLATE
26 . MAGAZINE FOLLOWER27.  MAGAZINE SPRING  
(NOT SHOWN)
28 . MAIN SPRING29. MAIN SPRING CAP30. MAIN SPRING CAP PIN31.  MAIN SPRING HOUSING 
(FLAT)
32 .  MAIN SPRING HOUSING PIN33.  MAIN SPRING HOUSING 
PIN RETAINER
34. PLUNGER LEVER
35. PLUNGER SPRING
36 . PLUNGER SPRING F/P37A. RECOIL SPRING OUTER
37B. RECOIL SPRING INNER
38A .  RECOIL SPRING GUIDE 
ROD  INNER38B.  RECOIL SPRING GUIDE PLATE38C .  RECOIL SPRING GUIDE 
ROD OUTER
39 .  RECOIL SPRING PLUG 40 . RECEIVER
41. SLIDE LOCK SAFETY
42. SAFETY LOCK PLUNGER
43. SEAR
44. SEAR PIN
45. SEAR SPRING
46 . SLIDE47. SLIDE STOP48. SLIDE STOP PLUNGER49. TRIGGER50. STRADDLE
51. TRIGGER PIN
52. TRIGGER RETURN SPRING
53. COCKING CAM
54. HAMMER RETURN SPRING
55 . SAFETY LOCK LEVER56. GRIP SAFETY LEVER57.  DRAWBAR PLATFORM SPRING58. HAMMER ASSEMBLY PIN59. DRAWBAR PLATFORM
RECOIL SPRING 
ASSEMBLY 
						

							
FIREARM RECORD
980 TAPSCOTT ROAD
SCARBOROUGH, ONTARIO M1X 1C3 (416) 297-7855 • FAX: (416) 297-1289 www.paraord.com
MANUAL #PO0904SB
Para
MODEL
SERIAL NO.
PURCHASED FROM
DATE PURCHASED
This instruction manual should always accompany this firearm  
and be transferred with it upon change of  ownership.