Para P13 .45, P14 .45 Instructions Manual

37
Figure 27
MAGAZINE
FOLLOWER
MAGAZINE
SPRING
MAGAZINE
EXTENSION
High-Capacity
Magazine Assembly10-Round
Magazine Assembly
HIGH-CAPACITY MAGAZINE (LEFT) IS FOR LAW ENFORCEMENT
ONLY. FOR RECREATIONAL USE, MAGAZINE CAPACITY IS
RESTRICTED TO 10 ROUNDS IN U.S.A. AND CANADA.
MAGAZINE
FLOOR
PLATE
MAGAZINE
BODY
MAGAZINE
RETAINING LIPS 

38
DISASSEMBLY
STEP 1: Remove all
ammunition from 
the magazine. Firmly
grasp the metal mag-
azine body in one
hand and with the
other hand grip the
magazine’s base
plate. Use your thumb
to slightly raise the
slotted tab at the rear
of the base plate.
CAUTION:  Lift the slotted tab only enough to clear the rear
of the magazine extension.
STEP 2:  Slide the base
plate towards the
front of the magazine
to remove it.
STEP 3: While holding
the magazine in one
hand, use the index
finger of the other hand to...

39
This will retract the two small tabs at the rear of the exten-
sionwhich keep it in place. Gently increase the pressure on
the release lever until some resistance is felt.
CAUTION: Do not apply excessive pressure to the release
lever or it may break off. 
CAUTION:  The spring and follower are  compressed in the 
magazine. Care should be taken dur ing this step to prevent
them from flying out.
STEP 4:  While maintain-
ing the gentle pressure
on the release lever,
begin to rotate the
magazine extension...

40
Clean all residue from the spring and from the
magazine follower.
CAUTION:Do not apply oil to any part or lubricate any
part of the magazine.
REASSEMBLY
STEP 5: Insert the spring and follower into the  opening at
the bottom of the metal magazine body.
CAUTION: Make sure that the rounded top edge of the
follower is at the front of the magazine.
Position the bottom of the spring around the four posts on 
the magazine extension. Then, gently compress the spring 
with the magazine extension so that it is...

41
STEP 6:With your
index finger, gently
depress the lever at 
the bottom of the 
extension. This will
allow you to re place
the base plate without
breaking the tab.
While holding the lever in a depressed position, begin to
replace the base plate by sliding it rearward from the front
of the extension. Be sure that the base plate engages the two
rails on the sides of the extension.
Continue to slide the base plate towards the rear until a
click is heard, indicating that the slotted tab at the rear of
the...

42
DO NOT STORE your pistol in anything which will attract
moisture, e.g., leather or heavy cloth, and do not store it in
an air-tight container or with a plug inserted in the barrel
for these are factors that can contribute to corrosion.
EXTENDED STORAGE requires that the internal mechanisms
are well oiled with an acid-free lubricating oil or preservative
while external mechanisms (receiver, barrel, etc.) should be
coated with an anti-rust oil.
COLD CLIMATE STORAGE requires that you make use of an oil...

43
For Para-Ordnance replacement parts please contact your
local dealer who should be able to assist you. Alternatively,
you can also contact the Para-Ordnance Parts Department by
mail or phone, for up-to-date information on the names and
locations of our Authorized Service Centers as well as current
parts prices.
PARTS AVAILABLE FOR SALE SHOULD BE INSTALLED AT 
A PARA-ORDNANCE AUTHORIZED SERVICE CENTER. 
OTHERWISE, IT IS THE PURCHASER’S TOTAL RESPONSIBILITY
TO MAKE ABSOLUTELY CERTAIN THAT ANY PARTS...

44
PARTS ILLUSTRATION 

45
1. BARREL
2. BARREL BUSHING
3. BARREL LINK
4. BARREL LINK PIN
5. DISCONNECTOR
6. EJECTOR
7. EJECTOR PIN
8. EXTRACTOR
9. FIRING PIN
10. FIRING PIN PLUNGER
11. FIRING PIN SPRING
12. FIRING PIN STOP
13. FRONT SIGHT
13L. FRONT SIGHT LIMITED
14. GRIP SAFETY
15. GRIP (SET)
16. GRIP SCREW (4)
17. HAMMER
17L. HAMMER LIMITED
18. HAMMER PIN
19. HAMMER STRUT
20. HAMMER STRUT PIN
21. MAGAZINE ASSEMBLY
22. MAGAZINE CATCH
23. MAGAZINE CATCH LOCK
24. MAGAZINE CATCH
SPRING
25. MAGAZINE FLOOR PLATE
26. MAGAZINE...

46
If any problem or question should arise with regard to the
performance of your firearm, please contact us, by mail or
telephone, and fully describe all circumstances involved.
This will allow us to determine the best way to handle your
problem. If authorized factory service is deemed necessary,
you will be given a return authorization number and 
shipping instructions.
WHEN AUTHORIZED TO SHIP YOUR FIREARM FOR ADJUSTMENT
OR REPAIR, PLEASE CAREFULLY NOTE THE FOLLOWING:
1. A detailed, written explanation...