Para LDA Instructions Manual

37
Figure 33
High-Capacity Magazine (left) is for law enforcement only. 
For recreational use, magazine capacity is restricted to 
10 rounds in the U.S.A. and Canada.
MAGAZINE
FOLLOWER
MAGAZINE
SPRING
MAGAZINE
EXTENSION
High-Capacity
Magazine Assembly10-Round
Magazine Assembly
MAGAZINE
FLOOR
PLATE
MAGAZINE
BODY
MAGAZINE
RETAINING LIPS
from the body. With the floor plate out of the way, remove
the spring and follower. Clean all components, taking care
to remove any powder deposits on the magazine...

38
TWO
SMALL
TABS
(REAR)
ROUND TAB
(FRONT)
STEP 3:While holding the maga-
zine in one hand, use the index fin-
ger of the other hand to gently
apply a small amount of pressure
to the release lever at the bottom
of the magazine extension. This will retract the two small tabs
at the rear of the extension which
keep it in place. Gently increase
the pressure on the release lever
until some resistance is felt.
CAUTION:Do not apply 
excessive pressure to the release
lever or it may break off.
CAUTION: The...

39
STEP 4: While maintaining the gentle pressure on the release lever, begin to rotate the 
magazine extension downward to release it from the metal magazine body. Release pressure
from the lever as soon as the two small tabs at the top rear of the extension clear the 
magazine body. The extension can now be removed by easing it slightly rearward to release the
round tab at the front. The spring and magazine follower can now be removed through 
the opening at the bottom of the metal magazine body. As you...

40
TRANSPORTATION AND STORAGE
While holding the lever in a depressed
position, begin to replace the base plate
by sliding it rearward from the front of
the extension. Be sure that the base plate
engages the two rails on the sides of the
extension.
Continue to slide the base plate towards
the rear until a click is heard, indicating
that the slotted tab at the rear of the
base plate has passed over the rear edge
of the extension, locking it in place.
Reassembly is now complete.
These instructions apply to...

41
WARRANTY INFORMATION
Para-Ordnance acknowledges its obligations under implied warranty legislation, with
respect to the sale of consumer goods, that may be in force in jurisdictions where its
products are sold. Due to differences in the extent and interpretation of such statutes,
and also on the basis of the Magnusson-Moss Warranty Act of the United States of
America, Para-Ordnance has elected not to offer any written or express warranty on its
product line and you are advised to consult existing...

42
Para-Ordnance is strongly committed to properly servicing its products, as it has over the
years, and in place of an express or written warranty it will provide all necessary service
for its pistols purchased after January 1, 2001 free of charge to the original purchaser
only, where adjustment or repair is required due to some defect in materials or workmanship.
If any problem or question should arise with regard to the performance of your firearm,
please contact us, by mail or telephone, and fully...

43
For Para-Ordnance replacement parts please contact your local dealer who should be
able to assist you. Alternatively, you can also contact the Para-Ordnance Parts
Department by mail or phone, for up-to-date information on the names and locations of
our Authorized Service Centers as well as current parts prices.
PARTS AVAILABLE FOR SALE SHOULD BE INSTALLED AT A PARA-ORDNANCE 
AUTHORIZED SERVICE CENTER. OTHERWISE, IT IS THE PURCHASER’S TOTAL 
RESPONSIBILITY TO MAKE ABSOLUTELY CERTAIN THAT ANY PARTS...

44
LDA SINGLE-STACK PARTS ILLUSTRATION 

45
1. BARREL
2. BARREL BUSHING
3. BARREL LINK
4. BARREL LINK PIN
5. DRAWBAR
6. EJECTOR
7. EJECTOR PIN
8. EXTRACTOR
9. FIRING PIN
10. FIRING PIN PLUNGER
11. FIRING PIN SPRING
12. FIRING PIN STOP
13/13L. FRONT SIGHT
14. GRIP SAFETY
15. GRIP (SET)
16. GRIP SCREW (4)
16A. GRIP SCREW
LOCKING RINGS
16B. GRIP SCREW BUSHING
17A. HAMMER
17B. HAMMER (SPURLESS)*
18. HAMMER PIN
19. HAMMER STRUT
20. COCKING CAM PIN
21. MAGAZINE ASSEMBLY
22. MAGAZINE CATCH
23. MAGAZINE CATCH LOCK
24. MAGAZINE CATCH SPRING
25. MAGAZINE...

46
LDA-SERIES PARTS ILLUSTRATION