Panasonic Wv Sf336 Installation Guide

							11
Precautions
Refer installation work to the dealer. 
Installation work requires technique and experi-
ences.  Failure  to  observe  this  may  cause  fire, 
electric  shock,  injury,  or  damage  to  the  prod-
uct. 
Be sure to consult the dealer. 
Stop the operation immediately when 
something is wrong with this product. 
When  smoke  goes  up  from  this  product  or  the 
smell  of  smoke  comes  from  this  product,  stop 
the  operation  immediately  and  contact  your 
dealer. 
Turn  the  power  off  immediately  and  contact 
qualified service personnel for service. 
Do not attempt to disassemble or modify 
this product. 
Failure to observe this may cause fire or electric 
shock. 
Consult the dealer for the repair or inspections. 
Do not insert any foreign objects. 
This could permanently damage the apparatus. 
Turn  the  power  off  immediately  and  contact 
qualified service personnel for service. 
Select an installation area that can sup-
port the total weight. 
Selecting  an  inappropriate  installation  surface 
may  cause  the  product  to  fall  down  or  topple 
over, resulting in injury. 
Installation  work  shall  be  started  after  sufficient 
reinforcement. 
Periodic inspections shall be conducted. 
Rust on the metal parts or screws may cause a 
fall  of  the  product  resulting  in  injury  or  acci-
dents. 
Consult the dealer for the inspections. 
Do not use this product in an inflammable 
atmosphere. 
Failure to observe this may cause an explosion 
resulting in injury. 
    Avoid installing this bracket in the loca-
tions where salt damage occurs or corro-
sive gas is produced. 
Otherwise,  the  mounting  portions  will  deterio-
rate and accidents such as a fall of this product 
may occur. 
The exclusively designed mount bracket 
shall be used. 
Failure to observe this may cause a drop result-
ing in injury or accidents. 
Use the exclusively designed mount bracket for 
installation. 
The screws and bolts must be tightened to 
the specified torque. 
Failure to observe this may cause a drop result-
ing in injury or accidents. 
Do not install this product in locations 
subject to vibration. 
Loosening  of  mounting  screws  or  bolts  may 
cause a fall of the product resulting in injury. 
Install this product in a location high 
enough to avoid people and objects from 
bumping the product. 
Failure to observe this may cause a drop result-
ing in injury or accidents. 
Do not strike or give a strong shock to this 
product. 
Failure to observe this may cause fire or injury. 
Do not rub the edges of metal parts with 
your hand. 
Failure to observe this may cause injury. 
Turn the power off when do wiring of this 
product. 
Failure  to  observe  this  may  cause  electric 
shock. 
In  addition,  short  circuit  or  wrong  wiring  may 
cause fire. 
     
						

							12
Turn the power off when cleaning of this 
product. 
Failure to observe this may cause injury. 
[Precautions for use]
This product is designed to be used 
indoors. This product is not operable out-
doors. 
This product has no power switch. 
When  turning  off  the  power,  turn  off  a  circuit 
breaker. 
To keep on using with stable performance
Do  not  use  this  camera  in  hot  and  humid  con-
ditions for a long time. 
Failure to observe this causes component deg-
radation resulting in life shortening of this prod-
uct. 
(Recommended operating temperature: +35 °C 
{95 °F} or lower)
Do  not  expose  this  camera  to  direct  heat 
sources such as a heater. 
Do not touch the dome cover with your 
bare hands. 
A dirty dome cover causes deterioration of pic-
ture quality. 
Handle this camera with care. 
Do  not  drop  this  camera,  nor  apply  shock  or 
vibration to this camera. 
Failure to observe this may cause trouble. 
About the PC monitor
Displaying  the  same  image  on  a  CRT  type 
monitor for a long time may damage the moni-
tor. It is recommended to use a screen-saver. 
When an error is detected, this product 
will restart automatically. 
This product  will  be  inoperable  for  around  2 
minutes after the restart just as when the power 
is turned on. 
     Product disposal/transfer
Images  saved  on  the  SDHC/SD  memory  card 
may lead to personal information leakage. 
When  it  is  necessary  to  dispose  or  give  this 
product  to  someone,  even  when  for  repair, 
make  sure  that  there  is  no  data  on  the  hard 
disk drives. 
Cleaning this product body
Be  sure  to  turn  off  the  power  before  cleaning. 
Do  not  use  strong  abrasive  detergent  when 
cleaning  this  camera.  Otherwise,  it  may  cause 
discoloration.  When  using  a  chemical  cloth  for 
cleaning,  read  the  caution  provided  with  the 
chemical cloth product. 
When the dirt is hard to remove, use a 
mild detergent and wipe gently. 
When  the  dirt  is  hard  to  remove,  use  a  mild 
detergent  and  wipe  gently.  Then,  wipe  off  the 
remaining detergent with a dry cloth. 
Cleaning the lens
Use  a  lens  cleaning  paper  (used  to  clean  cam-
era lenses or lenses of spectacles). When using 
solvent, use an alcohols solvent and do not use 
a thinner or a glass cleaner. 
Transmission interval
Image  transmission  interval  may  become  slow 
depending  on  the  network  environment,  PC 
performance,  shooting  subject,  access  num-
ber, etc. 
About SDHC/SD memory card
	 •	 Before	
inserting	the	SDHC/SD	 memory	
card,  turn  off  the  power  of  this  product 
first.    Otherwise,  it  may  cause  malfunction 
or  damage  data  recorded  on  the  SDHC/
SD  memory  card.    Refer  to  page  22  for 
descriptions  of  how  to  insert/remove  an 
SDHC/SD memory card. 
     
						

							13
	 •	 When	using	an	unformatted	 SDHC/SD	
memory  card,  format  it  using  this  camera. 
Recorded  data  on  the  SDHC/SD  memory 
card  will  be  deleted  when  formatted.  If  an 
unformatted SDHC/SD memory card or an 
SDHC/SD  memory  card  formatted  with 
other devices is used, this product may not 
work properly or performance deterioration 
may  be  caused.  Refer  to  the  Operating 
Instructions  (PDF)  for  how  to  format  a 
SDHC/SD memory card. 
	 •	 When	 some	SDHC/SD	 memory	cards	are	
used  with  this  product,  the  product  may 
not  work  properly  or  performance  deterio-
ration  may  be  caused.  Use  the  SDHC/SD 
memory cards recommended in page 42. 
Code label
The  code  labels  (accessory)  are  required  at 
inquiry  for  trouble.  Use  caution  not  to  lose 
these  labels.  It  is  recommended  to  paste  one 
of the labels onto the CD-ROM case. 
Discoloration on the color filter of the 
MOS image sensor
When  continuously  shooting  a  bright  light 
source such as a spotlight, the color filter of the 
MOS image sensor may have deteriorated and 
it  may  cause  discoloration.  Even  when  chang-
ing  the  fixed  shooting  direction  after  continu-
ously  shooting  a  spotlight  for  a  certain  period, 
the discoloration may remain. 
MPEG-4 Visual Patent Portfolio License
This  product  is  licensed  under  the  MPEG-4 
Visual  Patent  Portfolio  License  for  the  personal 
and  non-commercial  use  of  a  consumer  for  (i) 
encoding  video  in  compliance  with  the  MPEG-
4  Visual  Standard  ("MPEG-4  Video")  and/or  (ii) 
decoding MPEG-4 Video that was encoded by 
a  consumer  engaged  in  a  personal  and  non-
commercial activity and/or was obtained from a 
video provider licensed by MPEG LA to provide 
MPEG-4  Video.  No  license  is  granted  or  shall 
be  implied  for  any  other  use.  Additional  infor-
mation  including  that  relating  to  promotional, 
internal  and  commercial  uses  and  licensing 
may  be  obtained  from  MPEG  LA,  LLC.  See 
http://www.mpegla.com.
     AVC Patent Portfolio License
This  product  is  licensed  under  the  AVC  Patent 
Portfolio License for the personal and noncom-
mercial  use  of  a  consumer  to  (i)  encode  video 
in  compliance  with  the  AVC  Standard  ("AVC 
Video")  and/or  (ii)  decode  AVC  Video  that  was 
encoded by a consumer engaged in a personal 
and  non-commercial  activity  and/or  was 
obtained from a video provider licensed to pro-
vide  AVC  Video.  No  license  is  granted  or  shall 
be  implied  for  any  other  use.  Additional  infor-
mation  may  be  obtained  from  MPEG  LA,  LLC. 
See http://www.mpegla.com. 
						

							14
Precautions for Installation
Installation work shall be performed in accordance with the technology standard of the 
electric installation. 
    
This camera is designed to be used 
indoors. 
This product is not operable outdoors. 
Do not expose this camera to direct sunlight for 
hours  and  do  not  install  the  product  near  a 
heater  or  an  air  conditioner.  Otherwise,  it  may 
cause  deformation,  discoloration  and  malfunc-
tion.  Keep  this  camera  away  from  water  and 
moisture. 
Installing place
Do not place this product in the following plac-
es:
	 •	 Locations	where	it	may	 get	wet	 from	 rain	
or water splash
	 •	 Locations	 where	a	chemical	 agent	is	used	
such as a swimming pool
	 •	 Locations	 subject	to	humidity,	 dust,	steam	
and oil smoke
	 •	 Locations	 in	a	specific	 environment	 where	
a  solvent  or  a  flammable  atmosphere 
exists
	 •	 Locations	 where	a	radiation,	 an	X-ray,	 a	
strong  radio  wave  or  a  strong  magnetic 
field is generated
	 •	 Locations	 where	corrosive	 gas	is	pro-
duced,  Locations  where  it  may  be  dam-
aged by briny air such as seashores
	 •	 Locations	 where	the	temperature	 is	not	
within –10 °C to +50 °C {14 °F to 122 °F}. 
	 •	 Locations	 subject	to	vibrations	 (This	prod-
uct is not designed for on-vehicle use.)
	 •	 Locations	 subject	to	condensation	 as	the	
result of severe changes in temperature
    (In  case  of  installing  the  camera  in  such 
locations,  the  dome  cover  may  become 
foggy  or  condensation  may  be  caused  on 
the cover.)
     Be sure to remove this product if it is not 
in use. 
Shielded (STP) LAN cables must be used 
with this unit to ensure compliance with 
EMC standards. *
* PAL models only
Before installation
	 •	 The	
camera	mount	bracket	 described	 on	
page  19  shall  be  used  to  mount  the  cam-
era. 
	 •	 When	 this	camera	 and	camera	 mount	
bracket are mounted on a ceiling or a wall, 
use the screws described on page 19. The 
screws  to  be  used  are  not  provided. 
Prepare the screws according to the mate-
rial, structure, strength and other factors of 
the  mounting  area  and  the  total  weight  of 
objects to be mounted. 
	 •	 Ensure	 that	the	mounting	 surface,	anchor	
and screws are sufficiently strong. 
	 •	 Do	 not	mount	 this	product	 on	a	plaster	
board  or  a  wooden  section  because  they 
are too weak. If this product is unavoidably 
mounted  on  such  a  section,  the  section 
shall  be  sufficiently  reinforced  or  use  an 
optional ceiling mount bracket (WV-Q105). 
Screw tightening
	 •	 The	 screws	and	bolts	 must	 be	tightened	
with  an  appropriate  tightening  torque 
according  to  the  material  and  strength  of 
the installation area. 
	 •	 Do	 not	use	 an	impact	 driver.	Use	of	
an

	
impact  driver  may  damage  the  screws  or 
cause tightening excessively. 
	 •	 When	 a	screw	 is	tightened,	 make	the	
screw  at  a  right  angle  to  the  surface.  After 
tightening  the  screws  or  bolts,  perform 
visual check to ensure tightening is enough 
and there is no backlash. 
     
						

							15
Radio disturbance
When this product is used near TV/radio anten-
na, strong electric field or magnetic field (near a 
motor,  a  transformer  or  a  power  line),  images 
may be distorted and noise sound may be pro-
duced. 
PoE (Power over Ethernet)
Use  a  PoE  hub/device  that  is  compliant  with 
IEEE802.3af standard. 
Router
When  connecting  this  product  to  the  Internet, 
use  a  broadband  router  with  the  port  forward-
ing function (NAT, IP masquerade). 
Refer  to  the  Operating  Instructions  (PDF)  for 
further  information  about  the  port  forwarding 
function. 
Time & date setting
It  is  necessary  to  set  the  time  &  date  before 
putting this product into operation. Refer to the 
Operating Instructions (PDF) for further informa-
tion about the time & date setting. 
						

							16
Major operating controls
 * This  connector  is  provided  only  for  service.  Do  not  use  the  connector  for  checking  the  adjust-
ment of the angular field of view on the video monitor. 
    
FRONT 
TOP
MONITOR OUT
LOCK
12V   INBASE-T/
BASE TX
EXT
TOP
Marker
Direction marker for installation
Azimuth adjustment ring
Tilting table
Panning lock screw [LOCK] Panning table
Inner dome
Clear domeDome cover
(Provided only for service)
Monitor out connector for 
service*
Monitor out 
connector for 
adjustment 
(RCA jack) View from the side
12 V DC power supply 
terminal 
						

							17

About the [INITIAL SET] button
After turning off the power of the camera, turn on the power of the camera while holding down this 
button, and wait for around 5 seconds or more without releasing this button. Wait around 2 minutes 
after  releasing  the  button.  The  camera  will  start  up  and  the  settings  including  the  network  settings 
will  be  initialized.  Before  initializing  the  settings,  it  is  recommended  to  write  down  the  settings  in 
advance. 
FOCUS 
ASSIST
Tilting lock screw
INITIAL SET button
SDHC/SD memory card slot
Focus assist (F.A.) 
button
Access indicator (blinking at accessing)
Link indicator (lighting at linking)
SDHC/SD memory card error 
indicator/F.A. indicator
(Lights when the focus assist function 
is activated or when the focus ring is 
positioned near the best focus position)
SF335SF332
SF335SF332
AF
Auto focus (AF) 
button
SF336
SF336
SDHC/SD memory card error 
indicator/AF indicator
(Blinks when AF is being 
adjusted)
FRONT 
TOPEXT I/O
AUDIO
OUT
MIC/
LINE IN10BASE-T/
100BASE-IX
4
2
3 1
MONITOR
OUT
F N
Audio output connector
Microphone/line input connector
Network connector Lens
External I/O terminals
Zoom lock knob
Focus lock knobSF335
SF336
F N 
						

							18
Detaching the dome cover
Important:
	 •	 After	 removal,	retain	the	dome	 cover	fixing	screw	 so	as	not	 to	lose.	 The	screw	 is	required	 when	
attaching the dome cover. (☞ Page 34)
	 •	 Remove	 the	cover	 film	from	 the	dome  section  of  the  dome  cover  after  the  installation  is  com-
plete. Do not touch the dome section by hand directly after removing the cover film. 
z  Remove  the  dome  cover  fixing  screw  (M3, 
step screw, x1). 
x Rotate  the  dome  cover  counterclockwise  two  steps,  and  align  the  indication  "OPEN"  to  the 
maker of the camera to detach the dome cover.
Dome cover xing screw
(M3, step screw)
LOCK
ADJUST OPEN
ADJUSTOPENLOCK
Marker
Dome 
cover
Dome alignment 
indication 
OPEN
Dome section
ADJUST
OPENLOCK 
						

							19
Preparations
When  installing  the  camera  on  a  wall  or  a  ceiling,  there  are  four  methods  as  specified  below.  
(☞ Pages 20 and 21).
	 •	 Using	the	two-gang	junction	box
	 •	 Installing	the	camera	directly	on	the	ceiling	or	wall
	 •	 Using	the	optional	ceiling	mount	bracket	WV-Q168	(for	embedded	installation	on	a	ceiling)
	 •	 Using	the	optional	ceiling	mount	bracket	WV-Q105*
1 (for direct mounting on a ceiling) 
Important:
	 •	 Procure	 4	screws	 (M4)	to	secure	 the	camera	 to	a	wall	 or	a	ceiling	 according	 to	the	 material	 of	
the  installation  area.  In  this  case,  wood  screws  and  nails  should  not  be  used.  For  mounting  a 
camera  on  a  concrete  wall,  use  an  anchor  bolt  (for  M4)  or  an  AY  plug  bolt  (M4)  for  securing. 
(Recommended tightening torque: 1.6 N·m {1.18 lbf·ft})
	 •	 Required	pull-out	capacity	of	a	single	screw/bolt	is	196	N	{44	lbf}	or	more.	
	 •	 If	 a	ceiling	 board	such	as	plaster	 board	is	too	 weak	 to	support	 the	total	 weight,	 the	area	 shall	
be sufficiently reinforced or the optional ceiling mount bracket for the camera, WV-Q105, must 
be used. 
 
The mounting conditions of the camera are described as follows:
Installation 
place Applicable mount 
bracket Recommended 
screwNumber of 
screwMinimum pull-out 
strength (per 1 pc.)
Ceiling/wall Two-gang junction  box M4
4 pcs. 196 N {44 lbf}
Ceiling/wall (Direct mounting) M4 4 pcs. 196 N {44 lbf}
Ceiling WV-Q168 (approx.  280 g {0.8 lbs}) –
–*
2
Ceiling WV-Q105*1 (approx. 
150 g {0.8 lbs}) –
–*2
 *1  PAL models only
  *2  Make sure that the installed mount bracket can support more than 5 times of the weight of the 
camera. 
     
						

							20
Using the side cable access hole
When  installing  the  camera  directly  on  the  ceiling  or  wall  with  cables  exposed  or  when  using  the 
optional  ceiling  mount  bracket  WV-Q168,  cut  out  a  portion  of  the  dome  cover  to  open  a  cable 
access hole.
Side cable access hole
Side cable access hole
Method of camera installation
Using the two-gang junction box
Mount the camera on the two-gang junction box by fixing 4 screws (locally procured). (☞ Page 28)
FRONT 
TOPEXT I/O
AUDIO
OUTMIC
LINE IN10BAS
100BA
12V=IN
4
2
3 1MONITOR
OUT
N
F
Direction marker for installation
Two-gang junction box
Screws 
(locally procured)