Panasonic Wv Q151s Operating Instructions Manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
No model number suffix is shown in this manual.
Ceiling Mount Bracket
Operating Instructions
Model Nos.WV-Q151C/WV-Q151S 

2
CONTENTS
Preface ....................................................................................................................................... 2
Precautions ................................................................................................................................ 2
Major Operating Controls and Their Functions  .......................................................................... 4
Installations...

3
• Select an installation area that can support the total weight.
If a selected area is too weak to support the total weight, a fall of the product may occur
resulting in injury. Installation work shall be started after sufficient reinforcement.
• Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult
the dealer for the inspections.
• Do not rub the edges of metal parts with your hand.
Failure to observe this may cause...

4
Major Operating Controls and Their Functions 
Decorative cover Microphone stand* Fixing screw to be used
for cover fall preventionCamera mounting
plate Mounting base
Hole for microphone cable
Dome cover
Safety wire angle (Accessory)
Safety wire (Accessory)
Ceiling mount bracket
Decorative cover
WV-NS202
Dome cover Ceiling boardRoof space
* If a microphone is used, mount the microphone on the rubber-made microphone stand.
Unless the microphone is used, cut the rubber with a nipper or conduct another...

5
Installations
Be sure to read Precautions on the page xx before installation. The Installation Guide of the
network camera, WV-NS202, shall be read as well.
1. Remove the decorative cover.
qLoosen the fixing screw (unremov-
able) to be used for cover fall pre-
vention.
wUnhook the decorative cover from
the hooks (3 positions) of the cam-
era mounting plate and remove the
decorative cover by turning it coun-
terclockwise.
eTake the inner shell out.
2. Remove the camera mounting plate.
Remove the screws...

6
3. Put Template A (accessory) against the
ceiling and make a hole.
qMake 4 holes of 12 mm {1/2} in diam-
eter.
wRemove the center part from the tem-
plate.
eMake a hole of 160 mm {6-5/16} in
diameter.
* The hole shape is shown below.
4. Install two anchor bolts (M10 recommended) into the concrete ceiling.
qDetermine the anchor bolt length by use of Template B (accessory).
wPosition the nut by use of Template B (accessory). (The distance between the bottom
surfaces of the ceiling board and nut shall be...

7
5. Mount the safety wire angle (accessory) on the 2nd anchor bolt and connect the safe-
ty wire (accessory) to the angle.
qDisconnect the safety wire from the
safety wire angle.
wEngage the face marked qwith the
anchor bolt.
eBend the face marked w.
rConnect the safety wire to the safety
wire angle again.
Note:To use the anchor bolt that was already installed, the use of 2 spacer nuts is helpful.
6. Connect the mounting base to the tip
of the safety wire.
Spacer nuts
Safety wire
Spacer nuts
Safety wire...

8
Ceiling board
fixing screw
Ceiling
board fixing
bracket Insert the anchor bolt
Nut
Double nuts
Turn clockwise
7. Insert the mounting base into the hole
made in Step 1.
8. Secure the mounting base to the ceil-
ing board with the ceiling board fixing
screws (4 positions).
qEngage the top of the mounting base
with the 1st anchor bolt.
wSecure the mounting base by turning
the ceiling board fixing screws clock-
wise.
Turning the ceiling board fixing
screws clockwise provides ceiling
board tightening between...

9
10. Install the inner shell.
Slide the covers located on the both lat-
eral sides of the camera and put the
inner shell on the camera until the hooks
inside the inner shell are held in the
holes of the camera (until a click is
heard).
Important:Put the inner shell down on
the camera until the outside cover of
the camera cannot be seen from the
opening (from which the camera
lens is visible) of the inner shell. If
this integration is not successfully
performed, the inner shell may be
removed or the...

10
F
R
O
N
T
FRONTLO
C
K
Mounting base
Safety wire
FRONT
LOCK
Stationary portion
Center of the
camera mounting
plate
Camera fixing
screw
Lock plate
GuideRotating portion
Safety wire hook
11. Mount the camera on the camera
mounting plate.
qPut the camera onto the camera
mounting plate with aligning the lock
plate of the camera with the guide of
the camera mounting plate and
aligning the center of the camera
mounting plate with the center of the
screw for tripod mounting, and turn
the camera clockwise....