Panasonic Wv Nm100 Operating Instructions Manual

							31
The time on the browser will be displayed as hours
and minutes (00:00), though you can set hours, min-
utes and seconds in Time setup.
! Important
Click the [Setup] button.
The login window will appear when you press
the [Camera Control] button or the [Setup]
button on the “Top Menu” page for the first
time. The default settings for user name and
password are as follows.
User name: admin
Password: password
Change the default password for security.
! Important
STEP3
The Top Menu page appears.
The Basic setup page appears.
Screenshot 4
Screenshot 3
Set up the items on the Basic setup page.
This explanation is only for Camera setup.
Camera name
Enter a name for the camera. The entered cam-
era name will be displayed when the reload but-
ton of the browser is pressed or when the
browser starts up the next time.
Characters for Camera name:Up to 32 char-
acters
Time setup (year-month-day hour:min:sec)
Set the date and the time.
Year:Enter 4 digits.
Month and day:Enter 2 digits each.
Hour, minute and second:
Enter 2 digits each, and
divide by colon (:).
Power/Link/Access LED
Click the ON radio button to use the LED as
status display.
Click the OFF radio button to turn off the LED
all the time.
Camera position
Select Desk top or Wall mount according to
where the camera is installed.
Click the [SET] button after completing the set-
ting.
STEP5
STEP4 
						

							32
BROWSING PICTURES
If the setup has been completed, you can browse through the pictures on the camera.
The pictures of the camera can be displayed as still pictures or motion pictures.
Displaying multiple pictures of multiple cameras on a screen is also possible.
To display multiple pictures of multiple cameras on a screen, refer to page 36.
Monitoring a Still Picture of a Single Camera
Set as follows to monitor a still picture (JPEG) of a single camera.
Preparations
The setting for still pictures can be made in the Basic setup page.
Start up the browser and display the Basic setup page of the desired camera.
Refer to page 24 and 25 to display the Basic setup page.
Click the JPEG radio button for Operation
mode selection.
Begin the settings for JPEG.
JPEG mode setup
Set the following items for JPEG.
Refresh interval
Select a refresh interval from the following.
Fast / Middle / Slow / Very Slow
Image capture size
Select an image capture size from the following.
VGA (640 x 480) / QVGA (320 x 240) / QQVGA
(160 x 120)
Quality of image
Select a quality of the image from the following.
Super Fine / Fine / Normal / Low
Click the [SET] button after completing the set-
tings.
STEP3
STEP2
STEP1 
						

							33
Begin the operation from the Basic setup page.
The Control page appears and the still picture of the cam-
era is displayed. Operation buttons are displayed below the
still picture.
Screenshot 2
Screenshot 1
How to operate
If the preparations have been completed, you can begin the operation from the Basic setup page.
Click the Control button.
STEP1
Operate the camera and adjust the picture.
Panning and tilting
Click the arrow buttons (up / down / right / left)
to adjust the horizontal and vertical position.
The center of the box surrounded by the arrow
buttons (the point where the horizontal line and
the vertical line cross) is the current position of
the camera.
If you click inside the box surrounded by the
arrow buttons, you can pan and tilt the camera
wider than by clicking the arrow buttons.
Image capture size
Click one of the picture resolution buttons (VGA
(640 x 480) / QVGA (320 x 240) / QQVGA (160
x 120)) to display the picture with the desired
resolution.
Adjustment of the brightness of the picture
Click the buttons to adjust the brightness of the
picture. The left end button (-) is the darkest and
the right end button (+) is the brightest.
Image Size
Click one of the buttons (x1.0 / x1.5 / x2.0) to
select the desired image size.
When the picture is magnified, the quality of the
picture may be decreased.
AUX
Click one of the buttons (High/Low) to set the
status of the AUX output connector. (Refer to p.
53 for details.)
One time pan
You can monitor the picture by panning the
camera one time to the left and right.
STEP2
•If the preparations have been completed, start up the
browser and display the Top Menu page of the desired
camera. The camera picture appears on the Top Menu
page.
•Several pictures shot during the panning/tilting may not
be displayed when “Refresh interval” is set to “Very
Slow”.
Note 
						

							34
BROWSING PICTURES
Monitoring the Motion Picture of a Single Camera
Set as follows to monitor the motion picture (MPEG-4) of a single camera.
•To monitor the motion picture of a camera, installation of the plug-in is required.
For further information, refer to page 29.
•You may have problems browsing motion pictures depending on the bandwidth of the network to which the cam-
era is connected. In this case, perform the setting of “Bandwidth control” on the “Operation mode” page of
“Advanced setup”. For further information, refer to page 55.
Preparations
The setting for motion pictures can be made in the Basic setup page.
Start up the browser and display the Basic setup page of the desired camera.
Refer to page 24 and 25 to display the Basic setup page.
! Important
Begin the setting of the motion picture in
MPEG-4 mode setup.
Click the MPEG-4 radio button for Operation
mode selection.
The parameters for MPEG-4 setting automati-
cally appear.
Set the following items for MPEG-4.
Image capture size
Select an image capture size from the following.
CIF (352 x 288) / QCIF (176 x 144) 
Quality of image
Select a quality of the image from the following.
Fine / Normal / Low
Click the [SET] button after completing the set-
ting.
STEP3
STEP2
STEP1
(When “JPEG” is selected)
(When “MPEG-4” is selected) 
						

							35
Begin the operation from the Basic setup page.
The Control page appears. The motion picture of the cam-
era is displayed.
Screenshot 2
Screenshot 1
To display the motion picture of the selected
camera, click the [Live-ON] button.
To quit displaying the motion picture of the
selected camera, click the [STOP] button. The
motion picture disappears.
On this page, you can also operate the camera
and adjust the motion picture.
Panning and tilting
Click the arrow buttons (up / down / right / left)
to adjust the horizontal and vertical position.
The center of the box surrounded by the arrow
buttons (the point where the horizontal line and
the vertical line cross) is the current position of
the camera.
If you click inside the box surrounded by the
arrow buttons, you can pan and tilt the camera
wider than by clicking the arrow buttons.
Image capture size
Click one of the motion picture resolution but-
tons (CIF (352 x 288) / QCIF (176 x 144)) to dis-
play the motion picture with the desired resolu-
tion.
Adjustment of the brightness of the motion
picture
Click the buttons to adjust the brightness of the
motion picture. The left end button (–) is the
darkest and the right end button (+) is the
brightest.
Image Size
Click one of the buttons (x1.0 / x1.5 / x2.0) to
select the desired motion picture size.
When the picture is magnified, the quality of the
picture may be decreased.
AUX
Click one of the buttons (High/Low) to set the
status of the AUX output connector. (Refer to p.
53 for details.)
STEP2
•If the preparations have been completed, start up the
browser and display the “Top Menu” page of the desired
camera. The camera picture appears on the “Top Menu”
page.
•The port number for the MPEG-4 streaming is set to
5004. If another application uses this port, change the
port number to another even-numbered port number.
•To switch the currently monitored picture to another cam-
era picture, click the [STOP] button to stop displaying the
currently monitored picture. Then, enter the IP address of
the desired camera in the “Address” box of the browser
to monitor the desired camera picture.
Notes
How to Operate
If the preparations have been completed, you can begin the operation from the Basic setup page.
Click the [Control] button.
STEP1 
						

							36
BROWSING PICTURES
Monitoring Still Pictures of Multiple Cameras
You can monitor pictures of multiple cameras on a single monitor screen (multi-screen) simultaneously.
You can display multiple camera pictures from up to four cameras on a single monitor screen.
To monitor camera pictures on the multi-screen, registration of the cameras to be monitored on the multi-screen is
required.
You can register up to eight cameras as two groups by registering four cameras in each group.
•Only still pictures (JPEG) can be monitored on a multi-screen. You cannot monitor motion pictures (MPEG-4) on
a multi-screen.
•Select “OFF” for both “Host authentication” and “User authentication” of the camera to be registered for monitor-
ing on the multi-screen, or set the same user name and password to all of the cameras to be registered.
Preparations
Register the cameras to be monitored on the multi-screen.
First, the setting for still pictures on the Basic setup page is required.
Start up the browser and display the Basic setup page of the desired camera.
Refer to page 24 and 25 to display the Basic setup page.
! Important
Begin the operation from the Basic setup page.
Screenshot 1
Click the JPEG radio button for Operation
mode selection.
Set the details for JPEG in JPEG mode setup.
For further information, refer to page 32.
Click the [Advanced setup] button.
STEP3
STEP2
STEP1 
						

							37
The Operation mode page of Advanced setup appears.
The Multi-screen page appears.
Screenshot 3
Screenshot 2
Set the IP addresses of the cameras to be mon-
itored on the multi-screen.
You can register up to eight cameras as two
groups by registering four cameras in each
group.
Camera 1 – Camera 4 are registered as Group
A, and Camera 5 – Camera 8 are registered as
Group B.
Click the [SET] button after completing the set-
ting.
STEP6
STEP5
Click the [Multi-screen] button.
STEP4 
						

							38
BROWSING PICTURES
Begin the operation from the Multi-screen page.
The Control page appears. The still picture of the camera is
displayed.
The camera pictures are displayed on the quad screen.
Screenshot 3
Screenshot 2
Screenshot 1
If five cameras or more are connected, the next
multi-screen will be displayed by pressing the
[Group B] button.
STEP3
Click the [Quad screen] button.
STEP2
Click the [Control] button in the top left corner.
STEP1
How to Operate
If the settings of “Multi-screen” have been completed, you can begin the operation from the “Multi-screen” page. 
						

							39
Monitoring the Picture of a Camera in a Preset Position
You can monitor both the still picture and the motion picture of a camera installed in a place registered as a preset
position.
To monitor the image of the camera in a preset position, adjusting the position of the camera (horizontal and vertical
position) and registering the shooting location, as a preset position is required in advance.
Registration of a preset position
Begin to register a preset position of the camera.
Register the preset number and preset name of a preset position.
Up to eight preset positions can be registered.
Begin the operation from the Control page.
The Preset registration area appears below the list of Preset.
Screenshot 2
Screenshot 1
Click Preset Setup.
STEP1
Click the arrow buttons (up / down / right / left)
to adjust the horizontal and vertical position of
the picture.
After the adjustment of the position has been
completed, select a preset number and enter a
preset name for the preset position.
Characters for the preset name:1 character
to 32 characters
Click the [SET] button after completing the set-
ting.
Repeat STEP 2 to STEP 4 to register more pre-
set positions.
To add a registered preset position to Preset
tour, check the box next to the desired preset
name. (Uncheck the box to delete it from
Preset tour.)
STEP4
STEP3
STEP2
•If the preset position is not registered, you cannot
add the preset position to Preset tour.
•If a preset name is not entered, you cannot select
the preset position. (Preset name cannot be clicked
as it does not appear in the “Preset” area.)
! Important 
						

							40
BROWSING PICTURES
How to Operate
Monitor the picture of the camera in a preset position.
First, select whether a still picture or a motion picture is to be monitored in a preset position on the Basic setup
page. Refer to page 24 and 25 to display the Basic setup page.
Begin the operation from the Basic setup page.
The Control page appears.
(This screenshot is displayed when you choose a still picture to
be monitored in a preset position.)
The picture of the camera in the selected preset position
appears.
Screenshot 3
Screenshot 2
Screenshot 1
Select whether a still picture or a motion picture
is to be monitored in a preset position.
Refer to page 32 to monitor a still picture, and
page 34 to monitor a motion picture.
After the setting has been completed, click the
[Control] button.
STEP2
STEP1
Click the desired preset name from the list of
Preset.
STEP3
•You can also operate the camera and adjust
the picture. For further information, refer to
page 33.
•To register more preset positions or change
a registered preset position, click Preset
Setup. The Preset registration area
appears below the list of Preset and you
can register or change preset positions.
Notes