Panasonic Wv Nf302 Operating Instructions Manual

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Network Camera
Operating Instructions 
Model No.WV-NF302
WV-NF302 

2
CONTENTS
Preface ............................................................................................................................ 3
About these operating instructions  .............................................................................. 3
Trademarks and registered trademarks  ...................................................................... 3
Viewer software ........................................................................................................... 3
Monitor...

3
Preface
About these operating instructions
There are 3 sets of operating instructions as follows.
• Installation Guide
• Operating instructions
• Setup Instructions
These operating instructions contain descriptions of how to operate this product* using a PC via a network and of
how to configure the settings.
Refer to the installation guide for descriptions of how to install this product and of how to connect to a network.
Adobe
®Reader®is required to read PDF. When the Adobe Reader is not installed on...

4
Monitor images on a PC
The following are descriptions of how to monitor images from the camera on a PC.
Monitor images from a single camera
Important:
• To enhance the security, change the password for
the user admin. It is recommended to change this
password periodically.
• When displaying multiple MPEG-4 images on a PC,
images may not be displayed depending on the per-
formance of the PC.
Notes:
• Up to 16 users can access the camera concurrently
regardless of the image type (JPEG/MPEG-4) that
the...

5

• When On is selected for MPEG-4 transmission
JPEG (VGA or QVGA): 15 fps
JPEG (1 280 x 960): 5 fps
• When Off is selected for MPEG-4 transmission
JPEG (VGA or QVGA): 30 fps
JPEG (1 280 x 960): 11 fpsThe refresh interval may be longer depending on a
network environment, PC spec, photographic sub-
ject, access traffic, etc.
Refer to the following page for further information about
the Live page.
About the Live page
q[Setup] button *1
Click this button to display the setup menu. The but-
ton will turn...

6
tImage capture size buttons
These buttons will be displayed only when a JPEG
image is displayed.  
:The letters VGA will turn green and
images in the main area will be displayed
in VGA size. 
:The letters QVGA will turn green and
images in the main area will be displayed
in QVGA size. 
:
The letters 1 280 x 960 will turn green and
images in the main area will be displayed in 
1 280 x 960 (pixels).
Depending on the window size of the web
browser, it may become smaller than 1 280 x
960 pixels.
yZoom...

7
!6Audio output button *3
Turns on/off the audio transmission (play audio from
the PC on the camera speaker). This button will be
displayed only when Audio output, Interactive (full
duplex) or Interactive (half duplex) is selected for
Audio mode on the setup menu. (Setup
Instructions)
The button blinks while the audio transmission is
being carried out except the case of setting to
Interactive (full duplex).
When this button is clicked, the button will turn into
the  button and audio from the PC will...

8
Monitor images from multiple cameras
Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can
be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance. 4
cameras can be registered as a group and up to 4 groups (16 cameras) can be registered. (Setup Instructions)
Important:
• When simultaneously displaying images from 16 cameras on a multi-screen, zooming images from the WV-
NF302 and...

9
Record images on the SD memory card manually
Images displayed on the Live page can be recorded on the SD memory card manually.
This button is operable only when Manual is selected for Save trigger on the setup menu. (Setup Instructions)
Images recorded on the SD memory card can be copied onto the PC. (Setup Instructions)
Step 1
Display the Live page. (page 4)
Step 2
Click the [SD] button in the SD memory card box.
→The SD recording window will open.
Step 3
Click the [Start] button to start recording...

10
Action at an alarm occurrence
The alarm action will be performed when the following alarms occur.
Alarm type
Terminal alarm:When connecting an alarm device such as a sensor to the EXT I/O connector on the of the
camera, the alarm action (camera action at an alarm occurrence) will be performed when the connected
alarm device is activated.
VMD alarm:When motion is detected in the set VMD area, the alarm action will be performed.
* VMD stands for Video Motion Detection.
Command alarm:When a Panasonic...