Panasonic Wma Mp3 Cd Player Receiver Cq C9901u Operating Instructions

							®
WMA MP3 CD Player/Receiver with 512 Color OEL Display
Récepteur/lecteur CD avec écran OEL de 512 couleurs et lecture WMA/MP3
Reproductor de CD, WMA y MP3/receptor con pantalla OEL de 512 colores
CQ-C9901U
WMA MP3 CD Player/Receiver with Full Dot Matrix Display
Récepteur/lecteur CD avec afficheur matriciel et lecture WMA/MP3
Reproductor de CD, WMA y MP3/receptor con pantalla de matriz de puntos completa
CQ-C9801U/C9701U
SRC
CS
(CQ-C9901U)
YEFM285646A         ND1104-1015          Printed in China
Imprimé en Chine
Impreso en China Panasonic Consumer
Electronics Company,
Division of Matsushita Electric
Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.comPanasonic Sales Company,
Division of Matsushita Electric
of Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.comPanasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
CQ-C9901U/C9801U/C9701U®
Operating InstructionsManuel d’instructions
Manual de InstruccionesOperating Instructions
Manuel d’instructions
Manual de Instrucciones
¡Please read these instructions (including “Limited Warranty” and “Customer Services Directory”) carefully before using this product
and keep this manual for future reference.
¡Prière de lire attentivement ces instructions (y compris la “Garantie limitée” et le “Répertoire des services à la clientèle”) avant 
d’utiliser ce produit et conserver ce mode d’emploi pour s’y référer ultérieurement.
¡Lea estas instrucciones cuidadosamente antes de usar este producto y guarde este manual para usar como referencia futura.
TEXT 
						

							3English
2
Safety Information
Warning
Observe the following warnings when using
this unit.❑
The driver should neither watch the display nor
operate the system while driving.Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and use
the parking brake before watching the display or operating
the system.❑
Use the proper power supply.This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this prod-
uct with other battery systems, especially a 24 V DC battery
system.❑
Keep batteries and insulation film out of reach of
infants.Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.❑
Protect the Deck Mechanism.Do not insert any foreign objects into the slot of this unit.❑
Do not disassemble or modify the unit.Do not disassemble, modify the unit or attempt to repair the
product  yourself. If the product needs to be repaired, con-
sult your dealer or an authorized Panasonic Servicenter.❑
Do not use the unit when it is out of order.If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign matter in it, is exposed to water,
is smoking, or smells), turn it off immediately and consult
your dealer.❑
The remote control unit should not lie about in the
car.If the remote control unit lies about, it could fall on the floor
while driving, get wedged under the brake pedal, and lead to
a traffic accident.❑
Refer fuse replacement to qualified service person-
nel.When the fuse burns out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may lead
to smoke, fire, and damage to the product.
Observe the following warnings when
installing.❑
Disconnect the lead from the negative (–) battery
terminal before installation.Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a
short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY
SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND
PERSONAL INJURY OR DEATH.❑
Never use safety-related components for installa-
tion, grounding, and other such functions.Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.❑
Installing the product on the air bag cover or in a
location where it interferes with airbag operation is
prohibited.
❑
Check for piping, gasoline tank, electric wiring, and
other items before installing the product.If you need to open a hole in the vehicle chassis to attach or
wire the product, first check where the wire harness, gaso-
line tank, and electric wiring are located. Then open the hole
from outside if possible.❑Never install the product in a location where it inter-
feres with your field of vision.❑
Never have the power cord branched to supply other
equipment with power.
❑
After installation and wiring, you should check the
normal operation of other electrical equipment.The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.❑
In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑
Make sure the leads do not interfere with driving or
getting in and out of the vehicle.
❑
Insulate all exposed wires to prevent short circuit-
ing.
Caution
Observe the following cautions when using this
unit.❑
Keep the sound volume at an appropriate level.Keep the volume level low enough to be aware of road and
traffic conditions while driving.❑
Do not insert or allow your hand or fingers to be
caught in the unit.To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.❑
This unit is designed for use exclusively in automo-
biles.
❑
Do not operate the unit for a prolonged period with
the engine turned off.Operating the audio system for a long period of time with the
engine turned off will drain the battery.❑
Do not expose the unit to direct sunlight or exces-
sive heat.Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.❑
Do not use the product where it is exposed to water,
moisture, or dust.Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on rainy
days.Observe the following cautions when
installing.❑
Refer wiring and installation to qualified service
personnel.Installation of this unit requires special skills and experience.
For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from your
own installation of the unit.❑
Follow the instructions to install and wire the prod-
uct.Not following the instructions to properly install and wire the
product could cause an accident or fire.❑
Take care not to damage the leads.When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws, and
moving parts such as seat rails. Do not scratch, pull, bend or
twist the leads. Do not run them near heat sources or place
heavy objects on them. If leads must be run over sharp
metal edges, protect the leads by winding them with vinyl
tape or similar protection.❑
Use the designated parts and tools for installation.Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those sup-
plied or designated may result in internal damage to the unit.
Faulty installation may lead to an accident, a malfunction or
fire.❑
Do not block the air vent or the cooling plate of the
unit.Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑
Do not install the product where it is exposed to
strong vibrations or is unstable.Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.❑
Installation AngleThe product should be installed in a horizontal position with
the front end up at a convenient angle, but not more than
30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be installed.
Consult your dealer for further details.❑
Wear gloves for safety. Make sure that wiring is
completed before installation. 
❑
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)Observe the following cautions when handling
the batteries for the remote control unit.●Use only specified battery (CR2025).●Match the polarity of the battery with the (+) and (–) marks
in the battery case.●Replace dead battery as soon as possible.●Remove the battery from the remote control unit when not
using it for an extended period of time.●Insulate the battery (by placing them in a plastic bag or cov-
ering them with vinyl tape) before disposal or storage. ●Dispose of the battery according to the local regulations.●Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.In case of battery leakage●Thoroughly wipe the battery liquid off the battery case and
insert new battery.●If any part of your body or clothing comes into contact with
battery liquid, wash it with plenty of water.●If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical atten-
tion.
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or death.
■Read the operating instructions for the unit and all other com-
ponents of your car audio system carefully before using the
system. They contain instructions about how to use the sys-
tem in a safe and effective manner. Panasonic assumes no
responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning
This pictograph intends to alert you to the pres-
ence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material dam-
age.
Caution
CQ-C9901U/C9801U/C9701U
CQ-C9901U/C9801U/C9701U 
						

							5
CQ-C9901U/C9801U/C9701U
4
Safety InformationBefore Reading These Instructions
CQ-C9901U/C9801U/C9701U
Caution
THIS PRODUCT IS A CLASS I
LASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOUR-
SELF. REFER SERVICING TO QUALIFIED PERSONNEL.
The following applies only in the U.S.A.Part 15 of the FCC RulesFCC Warning:Any unauthorized changes or modifications to this
equipment would void the users authority to operate
this device.
Accessories
Notes:
¡The number in parenthesis underneath each accessory part name is the part number
for maintenance and service.
¡Accessories and their parts numbers are subject to modification without prior notice
due to improvements.
¡Mounting Collar and Trim Plate are mounted on the main unit at shipment.
Power Connector
(YEAJ02871)
Qty: 1
Lock Cancel Plate
Qty: 2
Mounting Bolt
Qty: 1
Tapping Screw
(5 mmø x 16 mm)
Qty: 1
Hex. Nut
(5 mmø)
Qty: 1
Mounting Collar
(YEFX0217222)
Qty: 1
Removable Face Plate
Case
(YEFA131646)
Qty: 1
SELSELSRCSRCBANDBANDMUTEMUTE23 1
5
8
06 4
9 7#VOLVOLDISPDISPCAR AUDIOMENU
SEL POWER
SOURCE
SRC
SET
BAND MUTE23 1
5
8
06 4
9 7#VOL
RANDOM
NUMBER TUNE TUNESCAN REPEATDISP
Remote Control Unit 
(Includes a battery:
CR2025)
(EUR7641010)
Qty: 1
Trim Plate
(YEFC05654):
CQ-C9801U, C9701U
(YEFC05655):
CQ-C9901U
Qty: 1
Owners Information
Card
Installation Instructions
(YEFM293921)
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXOO-OOOOO
Operating Instructions
(YEFM285646)
Instruction kitQty: 1 set
Installation kit (YEP0FZ5701)
Before Reading These Instructions
English
Rear Support Strap
(YEFG04019)
Qty: 1
CQ-C9901UWMA MP3 CD Player/Receiver with 512 Color OEL
(Organic electroluminescence) Display
CQ-C9801U/C9701UWMA MP3 CD Player/Receiver with Full Dot Matrix
Display
This operating instruction manual is for 3 models CQ-C9901U, CQ-C9801U and CQ-C9701U.
The difference among these models’ are mentioned below.
All screens and main body illustrations in this book represent CQ-C9901U unless otherwise specified.
CQ-C9901U CQ-C9801U / CQ-C9701U
Display unit 512 Color OEL Full Dot Matrix (Light Blue)
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected
components, and assembled by people who are proud of the reputation their work has built for our company. We know this product
will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be
proud to be a member of our family.
FeaturesModels
Differences 
among 3 models 
						

							7English
CQ-C9901U/C9801U/C9701U
6
CQ-C9901U/C9801U/C9701U
Service and Warranty
Limited Warranty
Customer Services Directory
U.S.A.Obtain Product Information and Operating Assistance;
locate your nearest Dealer or Servicenter; purchase Parts
and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
http://www.panasonic.com/support
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7
pm, EST.
For hearing or speech impaired TTY users, TTY : 1-877-
833-8855Accessory Purchases:Purchase Parts, Accessories and Instruction Books online
for all Panasonic Products by visiting our Web Site at:http://www.pasc.panasonic.com
or, send your request by E-mail to:
[email protected]
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American
Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY : 1-886-
605-1277Service in Puerto RicoMatsushita Electric of Puerto Rico, Inc. 
Panasonic Sales Company
Factory Servicenter:Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park,Carolina, Puerto Rico 00985
Phone (787) 750-4300, Fax (787) 768-2910
CANADAWARRANTY SERVICEFor product operation and information assistance, please
contact your Dealer or our Customer Care Centre at:
Telephone #: (905) 624-5505 Fax #: (905) 238-2360
Web: www.panasonic.ca
For product repairs, please contact one of the following:
•Your Dealer who will inform you of an authorized
Servicentre nearest you.
•Our Customer Care Centre at (905) 624-5505 or
www.panasonic.ca
•A Panasonic Factory Servicentre listed below:
Lachine, Quebec
Panasonic Canada Inc.
3075, rue Louis A. Amos
Lachine, QC H8T 1C4
Tel: (514) 633-8684
Fax: (514) 633-8020 Mississauga, Ontario
Panasonic Canada Inc.
5770 Ambler Dr.
Mississauga, ON L4W 2T3
Tel: (905) 624-8447
Fax: (905) 238-2418Calgary, Alberta
Panasonic Canada Inc.
6835-8
thSt. N. E. Calgary,
AB T2E 7H7
Tel: (403) 295-3955
Fax: (403) 274-5493 Richmond, British
Columbia
Panasonic Canada Inc.
12111 Riverside Way
Richmond, BC V6W 1K8
Tel: (604) 278-4211
Fax: (604) 278-5627
U.S.A.PANASONIC CONSUMER ELECTRONICS COMPANY, 
DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA 
One Panasonic Way, Secaucus, New Jersey 07094
PANASONIC SALES COMPANY, 
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
Ave. 65 de infanteria, Km. 9.5, San Gabriel Industrial Park
Carolina, Puerto Rico 00985PANASONIC AUTO PRODUCTS 
LIMITED WARRANTYLIMITED WARRANTY COVERAGE
If your product does not work properly because of defects in materi-
als and workmanship.Panasonic Consumer Electronics Company or Panasonic Sales Company
(collectively referred to as “the warrantor”) will, for the length of the peri-
od indicated in the chart below, which starts with the date of original pur-
chase (“warranty period”), at its option either (a) repair your product with
new or refurbished parts, or (b) replace it with a new or refurbished prod-
uct. The decision to repair or replace will be made by the warrantor.During the “Labor” warranty period, there will be no charge for labor.
During the “Parts” warranty period, there will be no charge for parts.
You must carry in or mail in your product during the warranty period.
If non-rechargeable batteries are included, they are not warranted.
This warranty only applies to products purchased and serviced in the
United States or Puerto Rico. This warranty is extended only to the
original purchaser of a new product which was not sold “as is”. A
purchase receipt or other proof of the original purchase date is
required for warranty service.
CARRY-IN OR MAIL-IN SERVICE
For Carry-In or Mail-In Service in the United States, call 1-800-211-
PANA (7262) or visit
Panasonic Web Site: http://www.panasonic.com
For assistance in Puerto Rico, call Panasonic Sales Company (787)-
750-4300 or fax (787)-768-2910.
LIMITED WARRANTY LIMITS AND EXCLUSIONSThis warranty ONLY COVERS failures due to defects in materials and
workmanship, and DOES NOT COVER normal wear and tear or cosmet-
ic damage. The warranty ALSO DOES NOT COVER damages which
occurred during shipment, failures which are caused by products not
supplied by the warrantor, failures which result from accident, misuse,
abuse, neglect, mishandling, misapplication, alteration, faulty installa-
tion, set-up adjustment, maladjustment of consumer control, improper
maintenance, improper antenna, inadequate signal reception or pickup,
power line surge, improper voltage supply, lightning, modification,
commercial use (such as use in hotels, offices, restaurants, or other
business uses) or rental use of the product, or service by anyone other
than the technician from Factory Servicenter or other authorized serv-
ice centers, or damage that is attributable to acts of God. THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER
“LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULT-
ING FROM THE USE OF THIS PRODUCT,  OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY.(As examples, this excludes damages
for lost time, cost of having someone remove or re-install an installed
unit if applicable, travel to and from the sevicer, and loss of media,
data or other memory contents. The items listed are not exclusive,
but are for illustration only.) ALL EXPRESS AND IMPLIED WAR-
RANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY,
ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied war-
ranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. If a problem with this
product develops during or after the warranty period, you may con-
tact your dealer or Servicenter. If the problem is not handled to your
satisfaction, then write to warrantor’s Consumer Affairs Department
at the addresses of the warrantor.
PARTS AND SERVICE WHICH ARE NOT COVERED BY THIS LIMITED
WARRANTY ARE YOUR RESPONSIBILITY.
Customer’s Record
Model
No.
SerialNo.
Dealer’sNo.
CodeNo.
Dealer’sAddress
Date of PurchaseCANADAPanasonic Canada Inc.
5770 Ambler Drive, Mississauga Ontario L4W 2T3PANASONIC PRODUCT LIMITED WARRANTYPanasonic Canada Inc. warrants this product to be free from defects
in materials and workmanship and agrees to remedy any such defect
for a period as stated below from the date of original purchase.
CAR AUDIO PRODUCT – ONE (1) YEAR, PARTS AND LABOUR
(The labour to install or remove the product is not warranted)
LIMITATIONS AND EXCLUSIONS
This warranty does not apply to products purchased outside Canada
or to any product which has been improperly installed, subjected to
usage for which the product was not designed, misused or abused,
damaged during shipping, or which has been altered or repaired in
any way that affects the reliability or detracts from the performance,
nor does it cover any product which is used commercially. Dry cell
batteries are also excluded from coverage under this warranty.
This warranty is extended to the original end user purchaser only. A
purchase receipt or other proof of the original purchase date is
required before warranty service is performed.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTIC-
ULAR PURPOSE.
IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES.
In certain instances, some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, or the exclusion of
implied warranties, so the above limitations and exclusions may not
be applicable.
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in
the original carton.
Include details of the defect claimed, and proof of the date of original
purchase.
Categories Parts Labor
Audio Components (except items listed below) One (1) Year One (1) Year
MXESeries Audio Components (except items
listed below)Two (2) Years Two (2) Years
Speakers One (1) Year Not Applicable
Accessories (in exchange for defective items)
Ninety (90) Days
Not Applicable 
						

							CQ-C9901U/C9801U/C9701U
CQ-C9901U/C9801U/C9701U
89
Contents
¡
Safety Information 2
¡
Before Reading These Instructions 4
¡
Service and Warranty 6
¡
Features 8
¡
Controls Layout 10
¡
Preparation 12
¡
General 14
¡
Sound Control 18
¡
Radio 21
¡
CD Player 24
¡
MP3/WMA Player 26
¡
XM Tuner (XM Direct
TM
receiver) 30
¡
Disc Changer
(when CDs or MP3 discs are loaded)
32
¡
Disc Changer (when DVDs or VCDs are loaded) 34
Features
¡
Audio Setting 36
¡
Function Setting 38
¡
Display Setting 39
¡
Customize the Display (Customize Function) 40
¡
Troubleshooting 42
¡
Error Display Messages 46
¡
Notes on Discs 47
¡
Maintenance 48
¡
Contents by Functions 48
¡
Specifications 49 English
Français50Español98
Common Each Source As Needed
New Features
Full Digital CD ReceiverThe CQ-C9901U/C9801U/C9701U uses Radio DSP for
digital conversion and processing of FM/AM signals, and
a digital amp to provide amplification of the digital data.
With this technology, Panasonic achieves full digital
processing of radio and CD signals from input to speaker
output. This means faithful reproduction of the original
sound.Radio DSPBy digitally converting and processing FM/AM broadcast
signals, this greatly reduces adjacent interference and
multipath distortion. 
A radios IF filter has the job of preventing neighboring
broadcast frequencies from interfering with reception of
your desired station. Panasonics Radio DSP uses an
advanced algorithm to perform this task with digital
control. It maintains the optimum balance between noise
suppression and sound quality by automatically adjusting
the IF filter bandwidth in response to the changing
interference characteristics as you drive.Fully Motorized Front PanelA touch is all it takes to slide the front panel down for
access to the disc slot. A three-stage tilt function permits
viewing angle to be adjusted to 15, 25 or 35 degrees for
optimum display visibility.256x64 pixel 512-color OEL display
(CQ-C9901U only)Multicolored expression can be achieved thanks to OEL
display. You can use this unit in your original way in
collaboration with the customization function.Sound ControlCS Auto (Circle Surround Automotive)CS Auto allows your car interior to change to a splendid
audio room in a moment. Every speaker can be fine-
tuned. (a page 18)
*CS Auto, TruBass, FOCUS, SRS and  symbol are
trademarks of SRS Labs, Inc.
CS Auto technology is incorporated under license from
SRS Labs, Inc.Note:If you enable CS Auto, the following functions are
automatically disabled:
SQ, POSITION, BASS/TREBLE, BALANCE/FADER, SUB-
WOOFER LEVEL, LPF, HPF, SBC-SW
SQ (Sound Quality)You have six preset modes (FLAT, POP, ROCK, VOCAL,
JAZZ, CLUB). You can customize your settings for these
(except FLAT) and save them for instant recall.
SQ9 (9-Band Sound Quality)
Center frequency and level are adjustable in each of nine
bands. This lets you fine tune sound quality for each
genre to suit car-interior acoustics and your personal
preferences. (a page 18)Full lineup of optional partsAn optional XM Direct
TMReceiver allows you to receive
the XM radio service. A DVD changer instead of an XM
Direct
TMreceiver is also connectable. (a page 30)
¡Toll free number
XM Tuner   P/N: XMD1000
Call 1-800-XM-RADIO (96-72346)
Extension cord   P/N: XMDPAN100
Call 1-800-942-TERK (8375)
The XM name and related logos are trademarks of XM
Satellite Radio Inc.
You can also enjoy watching DVDs if the optional DVD
changer and display unit are connected.
Notes:
¡A changer and an XM Direct
TMreceiver are not con-
nectable at the same time.
¡To connect the XM Direct
TMreceiver (
XMD1000
), it is
required to use an optional extension cord 
(
XMDPAN100
) that is produced by XM exclusively for
Panasonic products.
Delightful sound space thanks to system buildup
Sub-Woofer
(Option)CQ-C9901U/C9801U/
CQ-C9701U
Head unit
Stereo/Mono
Power Amplifier (Option) *XM Direct
TMreceiver
XMD1000: manufactured by XM Satellite Radio
(Option)
*DVD Changer
CX-DH801U
(Option)Headrest Monitor: CY-V7100U (Option)
*A changer and an XM Direct
TMreceiver
are not connectable at the same time. 
						

							CQ-C9901U/C9801U/C9701U
English
y/5
Pause/Play
BAND
SET
APM 
Auto Preset
Memory
11 10
Controls LayoutNote: This instruction manual explains operations for use with the buttons on the main unit. (Different operations excluded)
CQ-C9901U/C9801U/C9701U
SRC
CS
SELSEL
SRCSRCBANDBAND
MUTEMUTE23 1
5
8
06 4
9 7
#
VOLVOLDISPDISP
CAR AUDIOMENU
SEL POWER
SOURCE
SRC
SET
BAND MUTE23 1
5
8
06 4
9 7
#
VOL
RANDOM
NUMBER TUNE TUNESCAN REPEAT
DISP
One-touch operation is available for selecting a track
playing style by use of [4] (RANDOM), [5] (SCAN), or
[6] (REPEAT). (For a Folder/Disc playing style, hold
down the same button for 2 sec. or more.)Direct AccessA track (CD mode), disc (Disc changer), file, folder
(MP3/WMA mode) and channel (XM) can be directly
selected. 
Example: Track number 51
Press [#] (NUMBER).
2
Press [5].
3
Press [BAND] (SET). 
SRCSRCSRC POWERPOWERSOURCESOURCEPOWER
SOURCE
SRCSource
PWRPower
MUTE
SBC·SW Super Bass
Control·Subwoofer
CS 
Circle Surround Automotive
SQ Sound QualityMENU
DIM Dimmer
D•M Direct Memory VOLUME
PUSH SELSelect
DISP
Display
TUNE
TRACK 
(FILE)
Release
CSCS
TILT
OPEN (eject)
SRCSource
PWRPower
MUTE
SBC·SW Super Bass
Control·Subwoofer BAND
SET
APM 
Auto Preset
Memory
SELSelect
MENUVOLVolume
}:Up
{:Down
DISPDisplay
8
004 4RANDOMRANDOMRANDOM5
5SCANSCANSCAN6
6REPEATREPEATREPEAT77
99
#
#NUMBERNUMBERNUMBERNumber Buttons
~Number
RANDOM
SCAN
REPEAT99
TUNE
TRACK (FILE)
P·SET
(Preset)
DISC (FOLDER)
VOLVOLVOLDISPDISPDISP
BANDBANDSETSETSET
BAND
SELSELMENUMENUMENU
SEL
Controls Layout
Main Unit
Remote Control Unit Functions only by remote control unit
Disc slot
When Panel Opens
P·SET
Preset
DISC
(FOLDER
)
8
08
0
MUTEMUTEMUTE 
						

							CQ-C9901U/C9801U/C9701U
English13 12
Preparation
CQ-C9901U/C9801U/C9701U
Note: Adjust the clock when “ADJUST” appears on the
display.1
Press [MENU]to display the menu dis-
play.For using the remote control, hold down [MENU]
for 2 sec. or more.
2
Press []]or [[]to display the DIS-
PLAY menu.
3
Press [
{
]to select “CLOCK ADJ”.
4
Press [BAND] (SET) to confirm the dis-
play.
5
Adjust the setting value.
[[]
:Adjusting minutes
[]]
: Adjusting hours
[}
]: Forward
[{
]: Backward
6
Press [BAND] (SET) to confirm the
adjustment.
7
Press [MENU].For using the remote control, hold down [MENU]
for 2 sec. or more.
When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP]to change to regular mode.1
Set your car’s ignition switch to the ACC
or ON position.The demonstration screen appears.
Example: CQ-C9901U
2
Press [DISP](Display).The demonstration screen is cancelled, and no more 
appears.Note:If you would like to turn on the power and make
the demonstration message appear, hold down [SRC]
(PWR: Power) for 4 sec. or more after turning off the
power in other than the XM mode.
You may need to set the following depending on the
devices to be connected.Using Subwoofer¡Subwoofer level adjustment (apage 36)
¡Subwoofer low pass filter (apage 36)Connecting an XM Direct
TM
receiver
Preparation:¡Connect the optional XM Direct
TMreceiver (
XMD1000
).
¡
To connect the XM Direct
TMreceiver (XMD1000), it is
required to use an optional extension cord (XMDPAN100)
that is produced by XM exclusively for Panasonic prod-
ucts.
Getting StartedIt is required to sign up to become an XM Satellite Radio
subscriber. After checking your XM Satellite Radio ID,
sign up on the XM’s website or by calling them.1
Check of XM Satellite Radio ID¡Write down the ID indicated on the lower right of
your XM Direct
TMreceiver (XMD1000).
¡Check the ID shown by tuning your XM Radio to
channel 0. (apage 30)
2
Activate the XM Satellite RadioSelect either of the below to sign up.
¡Web site: http://www.xmradio.com/activation
¡Phone number: 1-800-XM-RADIO (96-72346)
Note: Refer to the operating instructions for the XM
DirectTMreceiver for details.
Connecting an AV device (TV, VTR)If you connect TV to AUX1 terminal, set the AUX1 setting
to TV.1
Press [SRC](Source) to select the
AUX1 mode. 
(apage 16)
2
Press [MENU]to display the menu dis-
play.For using the remote control, hold down [MENU]
for 2 sec. or more.
3
Press [BAND](SET)to adjust.
: TV
: Other devices (Default)
Note:When using an external TV unit manufactured by
a third party, select the TVmode.
4
Press [MENU]to confirm the adjust-
ment.
The following functions are activated when the Security
Function is ON. (a page 38)
¡The security indicator blinks when removing the face
plate.¡The alarm sounds and the message appears on the
screen to warn you to remove the face plate at power
off.
Security Indicator
SRC
CS
Preparation
First Time Power On
(DEMONSTRATION)
Remote Control Preparation Security Function
Setting
Other Settings Clock adjustment
(CLOCK ADJ)
Battery ReplacementPreparation Before Initial UsePull the insulation film out
from the backside of
remote control gently.
Warning
¡Keep batteries and insulation film out of reach of
infants. If an infant ingests a battery, please seek
immediate medical attention.
Caution
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do
not throw a battery into a fire or water.
¡Follow local regulations when disposing of a
battery.
¡Improper use of a battery may cause overheat-
ing, an explosion or ignition, resulting in injury
or a fire.
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
(Included in the remote control)
Battery Life: Approximately 6 months under nor-
mal use (at room temperature)
qw
qRemove the battery holder
with the remote control unit
placed on a flat surface.
qStick your thumbnail into
the groove, and push the
holder in the direction of
the arrow, and at the
same time.
wPull it out in the direction
of the arrow using a
tough pointed object.
wPut a battery in the case with
(+) side facing up.
ePut the case back.
2
3
Tough pointed object
Back side Insulation film 
						

							CQ-C9901U/C9801U/C9701U
English
Power onPress [SRC](PWR: Power).Notes:
¡The opening screen appears. You can overwrite the
opening screen (moving picture) with new one. (a
page 40)
¡When the power is switched on for the first time, a
demonstration message appears on the display. Press
[DISP]to change to regular mode. (apage 12)Power offHold down [SRC](PWR: Power) for 2 sec.
or more.Note:The ending screen appears. You can overwrite the
ending screen (moving picture) with new one. (apage
40)
14
GeneralThis chapter explains how to turn on or off the power, how to adjust the volume, etc.
CQ-C9901U/C9801U/C9701U
15
You can remove the face
plate to prevent it from
being stolen.Removing1
Turn off the power. 
(apage 14)
2
Press [] (Release).(The face plate disen-
gages with a click when
it is removed.)
The face plate automati-
cally closes in 5 sec-
onds if it is open or tilt-
ed.
The power is automatically turned off while the unit
is active.
3
Put the face plate in the case.
Mounting1
Slide the left side of the face plate in
place.
2
Press the right end of the face plate
until “click” is heard.
Cautions:
¡It is recommended to remove or mount the face
plate when the plate is at the closed position.
Do not remove or mount the face plate when the
plate is in motion.
¡This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡Do not remove the face plate while driving your car.
¡Do not place the face plate on the dashboard or
nearby areas where the temperature rises to high
levels.¡Do not touch the contacts on the face plate or on the
main unit, since this may result in poor electrical
contacts.
¡If dirt or other foreign substances get on the con-
tacts, wipe them off with clean and dry cloth.
¡To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
Open/EjectPress [] (OPEN).When a disc is already loaded, the disc will automatically
be ejected.ClosePress [] (OPEN).
TiltThe display angle changes among 4 levels as follows
every time you hold down [] (TILT)for 1 sec. or
more and release. Note:The last selected
angle is maintained even
after turning off the power.
Notes:
¡The volume level can be set independently for each
source. (For radio, one volume setting for AM, one
volume setting for all FMs)
¡The volume is not adjustable while an error display is
on the monitor. (apage 46)
qUp
wDown
Setting Range: 0 to 40
Default: 18Volume off (down)Press [](MUTE).CancelPress [](MUTE)again.Note: 
Volume-down range can be specified. (
apage
38)
General
Power On/off
(PWR: Power)
Face Plate Motion (Open/Close, Tilt)
(OPEN/CLOSE, TILT)
Volume Adjustment
(VOLUME)
Temporary Volume Off (Down)
MUTE (ATT: Attenuation)
Cautions:
¡To avoid damaging the face plate, do not push it
down or place objects on it while it is open.
¡Do not pinch your finger or hand in the face plate.
¡Do not insert foreign objects into the disc slots.
¡For the following cases, the face plate automatical-
ly closes. Use caution not to catch your finger.
¡After a lapse of 20 seconds
¡When a disc is inserted
¡When the face plate is removed (apage 14)
TILT 1
TILT 2
TILT 3
OPENTILT OFF
Face Plate Removing/Mounting
(Anti-Theft System)
SRC
CS
SRC
SRC
CS
SRC
CS 
						

							General
CQ-C9901U/C9801U/C9701U
17English
The display changes as follows every time [DISP]is
pressed.
Note:You can select a graphic pattern and a still image
from originally stored data. (apage 39) You can also use
your original images. (Customize Function apage 40)
At power-off:Clock display (default)
The dimmer level changes as follows every time you hold
down [MENU] (DIM:Dimmer)for 2 sec. or more.
Brighter (Default)
MediumMode
Folder hierarchy (MP3/WMA mode only.)
Ordinary display + graphic pattern
Ordinary display + still imageOrdinary display + clock
Display OFF
All displays disappear in 5 seconds.
XM Satellite Radio category  (XM Direct
TMreceiver mode only)
At power-on:
DarkerOff Only graphic pattern
Only still image
Display Change
(DISP: Display)
Dimmer Control
(DIM: Dimmer)
Note:This setting is not adjustable with the remote
control.
SRC
CS
SRC
CS
16
General
CQ-C9901U/C9801U/C9701U
RadioFM1, FM2, FM3, AM (apage 21)
Source Selection
(SRC: Source)
The source changes as follows every time 
[SRC]
(Source) 
is pressed.
PlayerAuxiliary (AUX 1)
Auxiliary (AUX2)
SRC
CS
SRC
When connecting CD Changer, DVD Changer (apage
32, 34)
When connecting XM Direct
TMreceiver (apage 30)
When connecting a device that is not
compatible with this unit
When loading CD (apage 24)
When loading MP3/WMA disc (apage 26)When connecting a TV
When connecting a device that is not compatible with
this unit
Note: Please connect a CD changer or a DVD changer to
AUX2. (aInstallation Instructions) 
						

							You can optimize the performance of CS Auto (Circle
Surround Automotive) by following the steps below.1
Set the CS Auto mode to on.
2
Hold down [CS](Circle Surround) for 2
sec. or more to display the audio menu
display.
3
Press [BAND]
(SET) to adjust.
4
Press [DISP]to confirm the adjustment.
SRC
CS
19English
CQ-C9901U/C9801U/C9701U
GeneralSound Control
CS Auto 
(Circle Surround Automotive )
CS Auto allows your car interior to change to a splendid
audio room in a moment. Every speaker can be fine-
tuned.
You can toggle the CS Auto function on and off every
time you press [CS](Circle Surround). Select CS Auto
on or off after setting each item.
Note:If you enable CS Auto, the following functions are
automatically disabled:
SQ, POSITION, BASS/TREBLE, BALANCE/FADER, SUB-
WOOFER LEVEL, LPF, HPF, SBC-SW
SRC
CSCS
18
CQ-C9901U/C9801U/C9701U
Lights when CS Auto is activated.
CS AUTO MODEThree-dimensional natural sound field is reproduced with
clarity in response to sound.
: Music 
(default in other than the AM mode)
: Cinema
: Monaural (default in the AM mode)
SBC-SW: Super Bass Control-SubwooferThe rear speaker can be used as a substitutional
subwoofer when a subwoofer is not connected.
Holding down [] (SBC-SW) for 2 sec. or more
toggles SBC-SW on and off.
CS AUTOMOTIVE MENU display
You can toggle the SQ function on and off every
time you press [CS](SQ).
Notes:
¡Each SQ level is changeable. (apage 20)
¡If you enable SQ, the following functions are
automatically disabled:
CS Auto, F-TruBass, R-TruBass, S.W.-TruBass,
F-Focus, R-Focus, F-R MIX
Lights when SQ is activated.
(Hidden in the FLAT mode)
SQ (Sound Quality)
SRC
CSCS
You have six preset modes (FLAT, POP, ROCK, VOCAL,
JAZZ, CLUB).SQ9 (9-Band Sound Quality)Center frequency and level are adjustable in each of nine
bands. This lets you fine tune sound quality for each
genre to suit car-interior acoustics and your personal
preferences.Off (default)
On
Notes:
¡If ON is selected, the settings of subwoofer level
adjustment and subwoofer low pass filter are activat-
ed. (apage 36)
¡When SBC-SW is set to ON, the CS mode automatical-
ly turns off.Lights when SBC-SW is activated.
SRC
CS
CS
Sound Control