Panasonic Wireless Speaker System Sc-ne1 Owners Manual

							VQT4T91
until 
2013/1/17
ENGLISH
ESPAÑOL
Owner’s Manual
Wireless Speaker System
Model No. SC-NE1
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this manual for future 
use.
If you have any  questions, contact:
U.S.A. and Puerto Rico: 1-800-211-PANA (7262)
Canada: 1-800-561-5505
Register online at www.panasonic.com/register
 (U.S. customers only)
Included Installation Instructions ( l2, 3 and 10, 11)
The installation work should be done by a qualified installation specialist.
Before commencing work, carefully read these  installation instructions and the operating 
instructions to ensure that installation is performed correctly.
(Please keep these instructions. You may need them when maintaining or moving this unit.)
La referencia rápida en español se puede encontrar en la página 13.
 
PPC
SC-NE1_PPC~VQT4T91.book  1 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							2
VQT4T91
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety 
instructions listed below. Keep these operating instructions handy for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in  accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or  grounding-type plug. A polarized plug has two blades with 
one wider than the other. A grounding-type plug has two 
blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the  manufacturer.
12 Use only with the cart, stand, tripod,  bracket, or table specified by the 
manufacturer, or sold with the 
apparatus. When a cart is used, use 
caution when moving the cart/apparatus 
combination to avoid injury from 
tip-over.
13 Unplug this apparatus during lightning storms or when 
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing 
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.
Unit≥To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or 
splashing.
– Do not place objects filled with liquids, such as vases, on 
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to 
qualified service personnel.
AC power supply cord≥The power plug is the disconnecting device. 
Install this unit so that the power plug can be unplugged from 
the socket outlet immediately.
Button-type battery (Lithium battery)≥Risk of fire, explosion and burns. Do not disassemble, heat 
above  60oC (140oF) or incinerate.
Unit≥Do not place sources of naked flames, such as lighted 
candles, on this unit.
Placement≥To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in 
cabinet or in another confined space. Ensure this unit is 
well ventilated.
– Do not obstruct this unit’s ventilation openings with 
newspapers, tablecloths, curtains, and similar items.
Button-type battery (Lithium battery)≥Danger of explosion if battery is incorrectly replaced. 
Replace only with the type recommended by the 
manufacturer.
≥ Keep out of reach of children.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte leakage and 
may cause a fire.
– Remove batteries if you do not intend to use the remote 
control for a long period of time. Store in a cool, dark 
place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct  sunlight for a long period of time with doors and windows 
closed.
– Do not touch the terminals ( i and j) with metal objects.
– Do not recharge, disassemble, remodel, heat or throw into fire.≥When disposing the batteries, please contact your local 
authorities or dealer and ask for the correct method of 
disposal.
WARNING
DO NOT INGEST BATTERY, 
CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause severe 
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the 
battery compartment does not close securely, stop using 
the product and keep it away from children.
If you think batteries might have been swallowed or placed 
inside any part of the body, seek immediate medical attention.
If any electrolyte should come into contact with your hands 
or clothes, wash it off thoroughly with water.
If any electrolyte should come into contact with your eyes, 
never rub the eyes. Rinse eyes thoroughly with water, and 
then consult a doctor.

This product contains a CR Coin Cell Lithium Battery which 
contains Perchlorate Material s special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate.
CAUTION
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicabl e safety 
instructions listed below. Keep these operating instructions handy for future reference.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in  accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, 
heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or  grounding-type plug. A polarized plug has two blades with 
one wider than the other. A grounding-type plug has two 
blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided 
plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the 
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the  manufacturer.
12 Use only with the cart, stand, tripod,  bracket, or table specified by the 
manufacturer, or sold with the 
apparatus. When a cart is used, use 
caution when moving the cart/apparatus 
combination to avoid injury from 
tip-over.
13 Unplug this apparatus during lightning storms or when 
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing 
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.
Unit≥To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or 
splashing.
– Do not place objects filled with liquids, such as vases, on 
this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to 
qualified service personnel.
AC power supply cord≥The power plug is the disconnecting device. 
Install this unit so that the power plug can be unplugged from 
the socket outlet immediately.
Button-type battery (Lithium battery)≥Risk of fire, explosion and burns. Do not disassemble, heat 
above  60oC (140oF) or incinerate.
Unit≥Do not place sources of naked flames, such as lighted 
candles, on this unit.
Placement≥To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in 
cabinet or in another confined space. Ensure this unit is 
well ventilated.
– Do not obstruct this unit’s ventilation openings with 
newspapers, tablecloths, curtains, and similar items.
Button-type battery (Lithium battery)≥Danger of explosion if battery is incorrectly replaced. 
Replace only with the type recommended by the 
manufacturer.
≥ Keep out of reach of children.
≥ Insert with poles aligned.
≥ Mishandling of batteries can cause electrolyte leakage and 
may cause a fire.
– Remove batteries if you do not intend to use the remote 
control for a long period of time. Store in a cool, dark 
place.
– Do not heat or expose to flame.
– Do not leave the battery(ies) in a car exposed to direct  sunlight for a long period of time with doors and windows 
closed.
– Do not touch the terminals ( i and j) with metal objects.
– Do not recharge, disassemble, remodel, heat or throw into fire.≥When disposing the batteries, please contact your local 
authorities or dealer and ask for the correct method of 
disposal.
WARNING
DO NOT INGEST BATTERY, 
CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the coin/
button cell battery is swallowed, it can cause severe 
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the 
battery compartment does not close securely, stop using 
the product and keep it away from children.
If you think batteries might have been swallowed or placed 
inside any part of the body, seek immediate medical attention.
If any electrolyte should come into contact with your hands 
or clothes, wash it off thoroughly with water.
If any electrolyte should come into contact with your eyes, 
never rub the eyes. Rinse eyes thoroughly with water, and 
then consult a doctor.

This product contains a CR Coin Cell Lithium Battery which 
contains Perchlorate Material s special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate.
CAUTION
SC-NE1_PPC~VQT4T91.book  2 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							3
VQT4T91
-If you see this symbol-
Table of contents
IMPORTANT SAFETY INSTRUCTIONS ............ 2
Accessories ....................................................... 4
About Bluetooth
®.............................................. 4
Control reference guide.................................... 5
Connections ...................................................... 6
Bluetooth
® operations ...................................... 7
Sound adjustment ............................................. 8
Others................................................................. 8
Troubleshooting ................................................ 9
Attaching the unit to a wall (optional) ........... 10
Specifications .................................................. 12
Unit care ........................................................... 12
License ............................................................. 12
Spanish Quick Reference / 
Referencia rápida en español ........................ 13
Limited Warranty (ONLY FOR U.S.A. AND 
PUERTO RICO) ................................................ 14
Limited Warranty (ONLY FOR CANADA)....... 15
Product Identification Marking is located on the bottom of 
the unit.
Information on Disposal in other Countries 
outside the European Union
This symbol is only valid in the 
European Union.
If you wish to discard this 
product, please cont act your local 
authorities or dealer and ask for 
the correct method of disposal.
The lightning flash with arrowhead symbol, within an 
equilateral triangle, is intended to alert the user to the 
presence of uninsulated “dangerous voltage” within 
the product’s enclosure that may be of sufficient 
magnitude to constitute a risk of electric shock to persons.
CAUTION
CAUTION :TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is 
intended to alert the user to the presence of important 
operating and maintenance (servicing) instructions in 
the literature accompanying the appliance.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
About descriptions in this Owner’s Manual
≥Pages to be referred to are indicated as “lOO”.≥ Unless otherwise indicated, operations are 
described using the remote control.
SC-NE1_PPC~VQT4T91.book  3 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							4
VQT4T91
AccessoriesAbout Bluetooth®
∫Frequency band used
≥This unit uses the 2.4 GHz frequency band.
∫ Certification of this device
≥This system conforms to frequency restrictions 
and has received certification based on 
frequency laws. Thus, a wireless permit is not 
necessary.
≥ The actions below are punishable by law in some 
countries:
– Taking apart or modifying the unit.
– Removing specification indications.
∫ Restrictions of use
≥Wireless transmission and/or usage with all 
Bluetooth® equipped devices is not guaranteed.
≥ All devices must conform to standards set by 
Bluetooth SIG, Inc.
≥ Depending on the specifications and settings of a 
device, it can fail to connect or some operations 
can be different.
≥ This system supports Bluetooth
® security 
features. But depending on the operating 
environment and/or settings, this security is 
possibly not sufficient. Transmit data wirelessly to 
this system with caution.
≥ This system cannot transmit data to a Bluetooth
® 
device.
∫ Range of use
≥Use this device at a maximum range of 10 m 
(33 ft). The range can decrease depending on 
the environment, obstacles or interference.
∫ Interference from other devices
≥This unit may not function properly and troubles 
such as noise and sound jumps may arise due to 
radio wave interference if this unit is located too 
close to other Bluetooth
® devices or the devices 
that use the 2.4 GHz band.
≥ This unit may not function properly if radio waves 
from a nearby broadcasting station, etc. is too 
strong.
∫ Intended usage
≥This unit is for normal, general use only.
≥ Do not use this system near an equipment or in 
an environment that is sensitive to radio 
frequency interference (example: airports, 
hospitals, laboratories, etc).
Check the supplied accessories before using this 
unit.
∏
1 Remote control (with a battery)
(N2QAYC000091)
∏ 1 AC power supply cord
(K2CB2CB00022)
Wall mounting accessories
∏ 1 Screw
(XTB3+8JFJK-J)
∏ 1 Safety holder
(RGQ0660-K)
∏ 2 Wall mount brackets
(RMQX1082-S)
(ONLY FOR CANADA)
The enclosed Canadian French label sheet corresponds to the 
English display on the top of the unit.
	≥ Do not use AC power supply cord with other equipment.
≥ Product numbers provided in this Owner’s Manual are 
correct as of December 2012. These may be subject to 
change.
Panasonic bears no responsibility for data 
and/or information that is compromised 
during a wireless transmission.
SC-NE1_PPC~VQT4T91.book  4 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							5
VQT4T91
ENGLISH
Control reference guide
1 Standby/on switch [Í/I] ([ Í])Press to switch the unit from on to standby mode or vice 
versa.
In standby mode, the unit is still consuming a small amount 
of power.
2 Enter sound menu
3 Enter setup menu
4 Select Bluetooth
®/AUX
5 Adjust the volume (0 (min) to 50 (max))
6 Enter the Bluetooth
® menu/
Change the sound input level of the external 
device ( l6)
7 Mute the sound
Mutes the sound. Press again to cancel.
“MUTE” is also canceled when the volume is adjusted or the 
unit is turned off.
8 Selection/OK
9 Dynamic Bass sound effect selector
10 Display
11 Remote control signal sensor
Distance: Within approx. 7 m (23 ft) directly in front.
≥ To avoid interference, please do not put any objects in 
front of signal sensor.
∫ Before using for the first time
Remove the insulation sheet  A .
∫To replace a button-type battery
Battery type: CR2025 (Lithium battery)
12
≥Set the button-type battery with its ( i) mark 
facing upward.
≥ Keep the button-type battery out of reach of 
children to prevent swallowing.
µ VOLUME ´
1
4 9 5
10 11
Top view
SOUND
SETUPPLAY MENU
OK 
1
4
2
5
6
7
8
3
SC-NE1_PPC~VQT4T91.book  5 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							6
VQT4T91
Connections
	≥These speakers do not have magnetic shielding. Do not place them near a television, personal computer or other devices easily 
influenced by magnetism.
∫ To select the sound input level of the external device
1 While in “AUX” mode, press [PLAY MENU] repeatedly to select “INPUT LEVEL” and then press [OK].
2 Press [ 3,4] to select “NORMAL” or “HIGH”.
≥ The default setting is “NORMAL”.
	≥Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal  will 
distort the sound.
≥ For details, refer to the instruction manual of the other equipment.
≥ The cables and the devices are not supplied.
Additional Connection
0â0ä0Á0ê0ï
Connect the AC power supply cord.
To a household AC outlet
AC Power supply cord (supplied)
This unit consumes a small amount of AC power (l
12) even when turned off.
≥In the interest of power conservation, if you will not be using this unit for an extended period of 
time, unplug it from the household AC outlet.
0â0ä0Á0ê0ï
Connect an external music device (for AUX mode).
1 Plug the audio cable (not supplied) into the AUX jack.
Plug type:  ‰3.5 mm (1/8q) stereo
2 Press [ , AUX] to select “AUX” and start playback on 
the connected device.
Audio cable (not supplied)
SC-NE1_PPC~VQT4T91.book  6 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							7
VQT4T91
ENGLISH
Bluetooth® operations
By using the Bluetooth® connection, you can listen to the sound from the Bluetooth® audio device from this 
unit wirelessly.
≥ Refer to the operating instructions of the Bluetooth
® device for details.
Preparation
≥ Turn on the Bluetooth
® feature of the device and 
place the device near this unit.
≥ If this unit is already connected to a Bluetooth
® 
device, disconnect it.
1Press [ , AUX] to select “BLUETOOTH”.
≥ If “PAIRING” is indicated on the display, go to step 3.
2Press [PLAY MENU] to select “NEW DEV.” and 
then press [OK].
{.“PAIRING” is indicated on the display.
3Select “SC-NE1” from the Bluetooth® device’s 
Bluetooth® menu.
4Start play on the Bluetooth® device.
	≥ If prompted for the passkey, input “0000”.
≥ You can register up to 8 devices with this unit. If a 9th device 
is paired, the device that has not been used for the longest 
time will be replaced.
Preparation
≥Turn on the Bluetooth® feature of the device and 
place the device near this unit.
≥ If this unit is already connected to a Bluetooth
® 
device, disconnect it.
1Press [ , AUX] to select “BLUETOOTH”.
{. “READY” is indicated on the display.
2Select “SC-NE1” from the Bluetooth® device’s 
Bluetooth® menu.
{. The name of the connected device is indicated on the 
display for 2 seconds.
3Start play on the Bluetooth® device.
	≥This unit can only be connected to one device at a time.
≥ When “BLUETOOTH” is selected as the source, this unit will 
automatically try and connect to the last connected 
Bluetooth
® device.
≥ The Bluetooth® device will be disconnected if “AUX” is 
selected as an audio source.
You can change the transmission speed to prioritize 
transmission quality or sound quality.
Preparation
≥ Press [ , AUX] to select “BLUETOOTH”.
≥ If a Bluetooth
® device is already connected, 
disconnect it.
1Press [PLAY MENU] repeatedly to select 
“LINK MODE”.
2Press [ 3,4 ] to select the mode and then 
press [OK].
MODE 1:  Emphasis on connectivity
MODE 2:  Emphasis on sound quality
	≥The default setting is “MODE 1”.
If the sound input level of the Bluetooth® transmission 
is too low, change the input level setting.
Preparation
≥ Connect a Bluetooth® device.
1Press [PLAY MENU] repeatedly to select 
“INPUT LEVEL”.
2Press [ 3,4] to select the level and then press 
[OK].
“LEVEL 0” 
,. “LEVEL +1” ,. “LEVEL +2”
^----------------------------------------------------J
	≥ Select “LEVEL 0” if the sound is distorted.
≥ The default setting is “LEVEL 0”.
1While a Bluetooth® device is connected:
Press [PLAY MENU] to select 
“DISCONNECT?”.
2Press [ 3,4 ] to select “OK? YES” and then 
press [OK].
Pairing Bluetooth® devices
Connecting a paired Bluetooth® 
device
Bluetooth® transmission mode
Bluetooth® input level
Disconnecting a Bluetooth® 
device
SC-NE1_PPC~VQT4T91.book  7 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							8
VQT4T91
Sound adjustment
The following sound effects can be added to the 
audio output.
1Press [SOUND] repeatedly to select the effect.
2Press [3,4] to select the setting and then 
press [OK].
* This function can also be selected with the [D.BASS] button  on the unit.
≥ You may experience a reduction in sound quality when these 
effects are used with some sources. If this occurs, turn the 
sound effects off.
Others
The sleep timer can turn the unit off after a set time.
1Press [SETUP] to select “SLEEP”.
2Press [ 3,4] to set the time (in minutes) and 
then press [OK].
“SLEEP 30”  ,. “SLEEP 60”  ,. “SLEEP 90” ,. “SLEEP 120”^--------------------. “OFF” (Cancel) (--------------------J≥The remaining time is indicated on the unit’s display 
except when other operations are performed.
The brightness of this unit’s display can be 
changed.
1Press [SETUP] repeatedly to select “DIMMER”.
2Press [ 3,4] to select “ON” and then press 
[OK].
	≥ To cancel the dimmer, select “OFF” in step 2.
As a factory preset, this unit will always turn off 
automatically if there is no sound output and no 
operation for approx. 30 minutes.
To cancel this function
1Press [SETUP] repeatedly to select 
“AUTO OFF”.
2Press [ 3,4] to select “OFF” and then press 
[OK].
	≥ To turn automatic standby on, select “ON” in step 2.
When other Panasonic equipment responds to the 
supplied remote control, change the remote control 
code.
1Press [ , AUX] to select “AUX”.
2While pressing and holding [  / AUX] on the 
unit, press and hold [SOUND] on the remote 
control until the unit’s display shows 
“REMOTE 2”.
3Press and hold [OK] and [SOUND] on the 
remote control for at least 4 seconds.
	≥To change the mode back to “REMOTE 1”, repeat the steps 
above but replace the button pressed on the remote control 
from [SOUND] to [ , AUX].
Direct-Vocal 
Surround
(D.SURROUND) “LEVEL 1”, “LEVEL 2” or 
“OFF”.
≥
The factory preset is “OFF”.
Preset EQ
(PRESET EQ) “HEAVY” (heavy), “SOFT” 
(soft), “CLEAR” (clear), 
“VOCAL” (vocal) or “FLAT” 
(flat/off).
≥
The factory preset is “HEAVY”.
Bass (BASS) or 
Treble (TREBLE) Adjust the level (
j4 to i 4).
Dynamic Bass* 
(D.BASS) “ON D.BASS” or
“OFF D.BASS”.
≥
The factory preset is 
“ON D.BASS”.
Sleep timer
Display brightness
Automatic standby
Changing the unit and remote 
control code
SC-NE1_PPC~VQT4T91.book  8 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							9
VQT4T91
ENGLISH
Troubleshooting
Before requesting service, make the following 
checks. If you are in doubt about some of the check 
points, or if the solutions indicated in the following 
guide do not solve the problem, refer to “Customer 
Services Directory (United States and Puerto Rico)” 
on page 14 if you reside in the U.S.A. or Puerto 
Rico, or refer to “Limited Warranty (ONLY FOR 
CANADA)” on page 15 if you reside in Canada.
Humming heard during play.
≥ An AC power supply cord or fluorescent light is near the 
cords. Keep other appliances and cords away from this unit’s 
cables.
Pairing cannot be done.≥Check the Bluetooth® device condition.
The device cannot be connected.≥The pairing of the device was unsuccessful or the registration 
has been replaced. Try pairing the device again.
≥ This unit might be connected to a different device. 
Disconnect the other device and try pairing the device again.
The device is connected but audio cannot be 
heard through this unit.
≥For some built-in Bluetooth® devices, you have to set the 
audio output to “SC-NE1” manually. Read the operating 
instructions for the device for details.
The sound is interrupted.≥ The device is out of the 10 m (33 ft) communication range. 
Bring the Bluetooth® device closer to this unit.
≥ Remove any obstacle between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band (wireless 
router, microwaves, cordless phones, etc.) are interfering. 
Bring the Bluetooth
® device closer to this unit and distance it 
from the other devices.
≥ Select “MODE 1” for stable communication. (l 7).
The remote control doesnt work properly.≥The remote control and this unit are using a different code. 
(l below, “REMOTE ”)
≥ Is the battery depleted or is the battery inserted incorrectly? 
(l 5)
The following messages or service numbers 
may appear on the units display.
“AUTO OFF”≥The unit has been left unused for about 30 minutes and will 
shut down within a minute. Press any button to cancel it.
“DIMMER”≥Appears 10 seconds after the volume is turned to “0”.
“ERROR”≥Incorrect operation is performed. Read the instructions and 
try again.
“F ” (“   ” stands for a number.)≥ There is a problem with this unit. 
Note down the displayed number, disconnect the AC power 
supply cord and consult your dealer.
“REMOTE ” (“   ” stands for a number.)≥The remote control and this unit are using different codes. 
Change the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and 
[ , AUX] for more than 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and  [SOUND] for more than 4 seconds.
To return all settings to the factory preset
When the following situations occur, reset the 
memory:
≥There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
1 Disconnect the AC power supply cord. (Wait 
for at least 3 minutes before proceeding to 
step  2.)
2 While pressing and holding down [ Í/I] on the 
unit, reconnect the AC power supply cord.
≥ Keep holding down [ Í/I] until “--------” 
appears on the display.
3 Release [ Í/I].
	≥ All the settings are returned to the factory preset. You will 
need to reset the memory items.
Common problems
Bluetooth®
Remote control
Messages
SC-NE1_PPC~VQT4T91.book  9 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分 
						

							10
VQT4T91
Attaching the unit to a wall (optional)
This unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the screw used 
and the wall are strong enough to support the weight of at least 33 kg (72.8 lbs).
The screws and other items are not supplied as the type and size will vary with each installation.
≥ Refer to step 2 of “Wall mount instructions” for details about the required screws.
≥ Be sure to attach the fall prevention cord as a secondary safety measure.
∫ Supplied accessories
≥1 Safety holder
≥ 1 Screw
≥ 2 Wall mount brackets
∫ Additionally required accessories 
(commercially available)
≥4 Wall mount bracket fixing screws
≥ 1 Safety holder fixing screw
≥ 1 Fall prevention cord*
≥ 1 Screw eye
* Use a cord that is capable of supporting over 33 k g (72.8 lbs) 
(with a diameter of about 1.5 mm (1/16q)).
1Measure and mark the position of the wall 
mount brackets (Both sides).
{. Use figures below to identify the screwing positions.
The position to attach the wall mount brackets
Space required
Installation accessories
≥Keep the safety holder out of reach of children to 
prevent swallowing.
≥ Keep the screws out of reach of children to prevent 
swallowing.
≥ Keep the wall mount brackets out of reach of children 
to prevent swallowing.
Safety precautions
Professional installation is required.
The installation should never be done by any 
other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY 
DAMAGE AND/OR SERIOUS INJURY, 
INCLUDING DEATH RESULTING FROM 
IMPROPER INSTALLATION OR INCORRECT 
HANDLING.
≥Be sure to install this unit as indicated 
within this Owner’s Manual.
Wall mount instructions
Before installation, turn the unit off and disconnect the 
AC power supply cord from the AC outlet.
252 mm (929/32q)
12.5 mm (
1/2q)
300 mm (1113/16q)
319 mm (12
9/16q)
770 mm (30
5/16q) 83 mm
(3
9/32q)
252 mm (9
29/32q) 82 mm (3
7/32q)
169 mm
(6
21/32q) 570 mm (22
7/16q)
67 mm (2
5/8q)
122 mm
(4
13/16q)
SC-NE1_PPC~VQT4T91.book  10 ページ  ２０１２年１２月１９日　水曜日　午後４時４３分