Panasonic Weather Band Receiver Cr W402ua Operating Instructions

11CR-W402UA
Radio
VOLUME/PUSHSEL
REWO
PR E
W
OPMP
AM PADN
A
BD N
A
B
123456
E
NU
T E
NU
T
KEE
SK EES
MUTEDISPDISP
SQCLOCK
CR-W402CR-W402UA R
W
P R
W
P
D
N
A
BD N
AB
TUNESEEK
qBand
Press [BAND] to change the band.
FM1FM2
AM162
(Weather Band)
FM stereo indicator, lights while receiving an FM stereo signal.
wManual Tuning
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Seek Tuning
Press and hold for more than 0.5 seconds and
release it.
[}TUNE]: Higher frequency
[{TUNE]: Lower frequency
Tuning will...

12CR-W402UA
Radio (Continued)
Preset Station Setting
Up to 6 stations can be saved in each of the FM1, FM2 and
AM preset station memories.
Note: Existing saved stations are overwritten with new
stations after following this procedure.
VOLUME/PUSHSEL
R
E
WOP R
E
WOPM
P
AM P
AD
N
A
B D
N
A
B
123456
ENU
TE NUT
KEE
S KEES
MUTEDISPDISP
SQCLOCK
CR-W402CR-W402UA RW
P RWP
BAND
123456
Preset buttons from [1] to [6]
blinks oncePreset Number
Caution
To ensure safety, never attempt to preset stations
while you are...

13CR-W402UA
VOLUME/PUSHSEL
R
E
WO
P RE
WOPMPA
M
P
ADNA
BD NAB
123456
E
NU
T E
NU
T
KEE
SK EES
MUTEDISPDISP
SQCLO CK
CR-W402CR-W402UA R
W
PR W
P
123456
T uning in a Weather Band Station
• Press [BAND] (APM) to select WB (Weather Band). (a page 11)
• Press any of the buttons  [1]to [6] to monitor the preset station.
Weather Band Stations
National Weather Radio Broadcasts from over 380 Iocations throughout
the U.S. on seven VHF/FM frequencies.
Tune to weather band to receive continuous weather information...

14CR-W402UA
Troubleshooting
Tr oubleshooting Tips
■ Common
The ground lead is not connected properly.
a Connect the ground lead properly.Noise. Mute is set to ON.
a
Set it to OFF.
Cables are not correctly connected.
aConnect cables correctly.No sound. Vehicle’s ignition switch is not on.
a
Turn your vehicle’s ignition switch to ACC or ON.
Cables are not correctly connected.
aConnect cables correctly.
Power connector is not correctly connected.
aConnect the power connector to the terminal that is always...

15CR-W402UA
■Sound Setting
The right speaker wire is connected to the left speaker and the left spe\
aker
wire to the right speaker.
a Connect the speaker wires to the correct ones.Left and right sounds
are reversed in stereo
listening. Left and right balance, or front and rear balance is off on one side.
a
Adjust BAL/FAD as appropriate.
Cables are not correctly connected.aConnect the cables correctly.
No sound from left,
right, front, or rear
speaker.
Problem
Possible causeaPossible solution
Product...

16CR-W402UA
Speaker Connections
Care of the Unit
❐ Cleaning this Unit
Use a dry, soft cloth to wipe.
❐Caution on Cleaning
Never use solvents such as benzine, thinner as they may
mar the surface of the unit.
Your product is designed and manufactured to ensure the minimum of maint\
enance. Use a soft cloth for routine exterior
cleaning. Never use benzine, thinner, or other solvents.
Wa rning
Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the...

17CR-W402UA
Installation Guide
WARNING
❐ This installation information is designed for experienced installers and\
 is not
intended for non-technical individuals. It does not contain warnings or \
cautions of
potential dangers involved in attempting to install this product.
Any attempt to install this product in a vehicle by anyone other than a \
qualified installer
could cause damage to the electrical system and could result in serious \
personal injury
or death.
❐ If your vehicle is equipped with air...

18
CR-W402UA
Installation (continued)
❏Precautions
¡Disconnect the cable from the negative  @battery
terminal (see warning and caution below).
¡Remove Mounting Collar  qfrom the main unit
temporarily, which are already mounted at shipment.*
¡
Unit should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
❏ Dashboard Installation
Installation Opening
Less than 30˚
Caution
Various settings that have been stored in the memory in
other on-board equipment...

19CR-W402UA
Caution
¡We strongly recommend that you wear gloves for installation work to prot\
ect yourself from injuries.
¡When bending the mounting tab of the mounting collar with a screwdriver,\
 be careful not to injure your hands and fingers.
First complete the electrical connections, and then check them for corre\
ctness.( apage 20)
The included Mounting Collar  qis designed specially for this unit. Do not use it to attach any other m\
odel.
q
Insert the Mounting Collar  qinto the
dashboard, and...

20CR-W402UA
Electrical Connections
Caution
• This wiring information is for experienced technical individual, for saf\
ety reason, please your dealer wire this connection.
• This product is designed to operate with a 12 V DC, negative ground batt\
ery system.
• To prevent damage to the unit, be sure to follow the connection diagram \
below.
• Do not insert the power connector into the unit until the wiring is comp\
leted.
• Be sure to insulate any exposed wires from a possible short-circuit from\
 the...