Panasonic Video Intercom System Monitor Station Vl Gm301a Installation And Operation Guide

							31
Using the unit
Opening a door (door opener)
You can open the door using the monitor station and sub monitor station (a separate
door opener is required).
1While the display is on, press and hold²DOOR³.
•Up to 2 door opener may be connected. (Page 14) When the monitor station
receives a call from door station1, pressing ²DOOR³with the door station1
image displayed activates the opener of door station1. Likewise, if the call is
from door station2, pressing ²DOOR³activates the opener of door station2.
Note:
•See page 14 for wiring information.²DOOR³ 
						

							32
MENU (1/4) screen
(Pages 36 – 37)
RECEIVE VOLUME
(Page 36)
When²MENU³is pressed, the MENU (1/4)
screen is displayed.
After this, follow the instructions appearing on
the screen to carry out the various operations
and settings.
•Refer to the reference pages for each
screen for details.
Menu setup
Monitor station/Sub Monitor station screen configuration
(The displays shown for each screen are the default displays.)
MENU (3/4) screen
(Pages 41 – 44)
GROUP SETUP
(Page 41)
•The sub monitor station does not have a “RINGER SELECT”
and “PBX SELECT” setting.
MENU (4/4) screen
(Pages 45 – 46)
CONTACT CLOSURE
(Page 45)
²MENU³
MENU (2/4) screen
(Pages 38 – 40) 
						

							33
Sub Monitor station menu screen
•The sub monitor station does not have a “RINGER SELECT” and “PBX
SELECT” setting.
Menu setup
RINGER VOLUME
(Page 37)
CAMERA SELECT
(Pages 42, 43)
COMMUNICATION
(Page 44)
INITIALIZATION
(Page 46)
RINGER SELECT
(Pages 38, 39)PBX SELECT
(Pages 40) 
						

							34
Menu setup
Display the menu screen and then make the settings
1Press²MENU³.
3 Moving the cursor
Cursor
The “MENU (1/4)” screen will be displayed.
2
Each time you press²SELECT ()³, the cursor moves down.
Each time you press²SELECT (
)³, the cursor moves up.
When the cursor is at the lowest row or the highest row, the menu screen
will change when you press²SELECT (/
) ³again.
Cursor
Cursor
press
²SELECT ()³.
press
²SELECT (
)³.
4Move the cursor to the desired item and then Press²MENU³.
²SELECT (
) ³
²SELECT () ³
²MENU³
²TALK³ 
						

							35
Note:
•If you do not carry out any operation for approximately 5 minutes while a menu
screen/setting screen is displayed, the screen will disappear automatically and
the setting will end.
– Some settings will return to the previous settings.
•If a call comes from a door station or from the monitor station and sub monitor
station while you are making a menu setting, the menu setting will automatically
end.
5 Make the setting
Menu setup
 RECEIVE VOLUME : page 36
 RINGER VOLUME :page 37 RINGER SELECT :pages 38, 39 PBX SELECT :page 40
 GROUP SETUP :page 41
 CAMERA SELECT :pages 42, 43
 COMMUNICATION : page 44 CONTACT CLOSURE : page 45 INITIALIZATION : page 46
6Once the setting is complete, Press²MENU³.
(The display will return to the menu screen.)

•For some screen, you should move the cursor to
“BACK” and then press²MENU³to return to the
menu screen.
•To make another setting, repeat steps 3 to 6.
7
Press²SELECT ()³ to move the cursor to
“MENU EXIT”. Cursor
8
Press²MENU³.

•You can cancel (end) a menu setting by pressing²TALK³while making
the menu setting. 
						

							36
This sets the receive volume for the door station and the monitor station or sub
monitor station.
Menu setup
Setting the receive volume (Default setting is “MID”.)
5 To continue making further settings ...
Move the cursor to the desired item, and press²MENU³.
(Refer to step 5 on page 35.)Press²MENU³.
( The “MENU (1/4)” screen will be displayed.)
1Cursor
2
Check that the cursor is positioned at
“RECEIVE VOLUME”, and then press²MENU³.
( The “RECEIVE VOLUME” screen will be displayed.)
3Press²SELECT (
/)³to adjust the receive volume.
• The setting can be made in 3 steps from “LOW” to “HIGH”.
4Once the receive volume setting has been made,
press²MENU³.
( The display will return to the “MENU (1/4)” screen.)

To complete the settings ...
Press²SELECT ()³to return to the “MENU (4/4)”
screen, and then move the cursor to “MENU EXIT”
and press²MENU³. Cursor
²SELECT (
) ³
²SELECT () ³
²MENU³ 
						

							37
²SELECT (
) ³
²SELECT () ³
²MENU³
Menu setup
Setting the ringer volume (Default setting is “HIGH”.)
This sets the ringer volume for the door station and the monitor station or sub
monitor station.
6 To continue making further settings ...
Move the cursor to the desired item, and press²MENU³.
(Refer to step 5 on page 35.)Press²MENU³.
( The “MENU (1/4)” screen will be displayed.)
1
Cursor
2
4
Press²SELECT (
/)³to adjust the ringer volume.
• The setting can be made in 3 steps from “OFF” to “HIGH”.
3
To complete the settings ...
Press²SELECT ()³to return to the “MENU (4/4)”
screen, and then move the cursor to “MENU EXIT”
and press²MENU³.
Press²SELECT ()³ to move the cursor to
“RINGER VOLUME”.
Press²MENU³.
( The “RINGER VOLUME” screen will be displayed.)
5
Once the ringer volume setting has been made,
press ²MENU³.
( The display will return to the “MENU (1/4)” screen.)
 
						

							38
Menu setup
Selecting the ringer
(Default settings are “CAMERA1: BELL1” and “CAMERA2: BELL2”.)
This selects the ringer tone for CAMERA1 and CAMERA2.
Press²MENU³.
( The “MENU (1/4)” screen will be displayed.)
1Cursor
2
4
Press²SELECT (
/)³to
move the cursor to the camera for the ringer tone
you would like to select.
5
Press²SELECT ()³to  move the cursor to
“RINGER SELECT”.
3
Press²MENU³.
( The “RINGER SELECT” screen will be displayed.)
Press²MENU³.
( The “RINGER SELECT” screen for the
corresponding
 camera will be displayed.)
²SELECT (
) ³
²SELECT () ³
²MENU³ 
						

							39
Menu setup
6Press²SELECT (
/)³to move the cursor to the tone you would like to select.
7Press²MENU³.
•The selected ringer will sound.
(The display will return to the “RINGER SELECT”
screen.)

8To select ringer tone, repeat steps 4 to 7.
9
Once you have selected the ringer tone, press
²SELECT  ()³to move the cursor to “BACK”.
10
Press²MENU³.
( The “MENU (2/4)” screen will be displayed.)
11  To continue making further settings ...
 Move the cursor to the desired item, and press²MENU³.
 (Refer to step 5 on page 35.)
Press²SELECT ()³to return to the “MENU (4/4)”
screen, and then move the cursor to “MENU EXIT”
and press²MENU³.
To complete the settings ... 
						

							40
²SELECT (
) ³
²SELECT () ³
²MENU³
Menu setup
Selecting the PBX (Default setting is “ON”.)
This select the PBX for the door calls from any telephone.
6 To continue making further settings ...
Move the cursor to the desired item, and press²MENU³.
(Refer to step 5 on page 35.)Press²MENU³.
( The “MENU (1/4)” screen will be displayed.)
1Cursor
2
4
Press²SELECT (
/)³to move the cursor to “ON” or “OFF”.
• ON : PBX is used.
• OFF : PBX is not used.
3
To complete the settings ...
Press²SELECT ()³to return to the “MENU (4/4)”
screen, and then move the cursor to “MENU EXIT”
and press²MENU³.
Press²SELECT ()³ to move the cursor to
“PBX SELECT”.
Press²MENU³.
( The “PBX SELECT” screen will be displayed.)
5Once the PBX setting has been made,
press ²MENU³.
( The display will return to the “MENU (2/4)” screen.)