Panasonic Video Cassette Recorder Pv V402 Operating Instructions

							Please read these instructions carefully before attempting to connect, 
operate or adjust this product. Please save this manual. 
Spanish Quick Use Guide is included. 
(Guía para rápida consulta en español está incluida.)
LSQT0532B
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to :\
 [email protected]
Video Cassette Recorder
Operating Instructions
(Basic Operations)
For advanced operations, see the separate 
“Advanced Operations” instruction book.
Model No. PV-V402
Table of Contents
Important Safeguards and Precautions .................... 2 
Before Using ............................................................ 3 
Connections and Initial Setup (Ready to Play) ......... 4 
Playback / Record on a Tape ................................... 5 
Timer Recording ....................................................... 6 
Location of Controls ............................................. 7, 8 
Spanish (Español) Quick Use Guide ............ 9, 10, 11 
Limited Warranty / Customer Services Directory .... 12
As an ENERGY STAR ® Partner,
Matsushita Electric Corporation of America has determined that this product or productmodel meets the 
ENERGY STAR ®
guidelines for energy efficiency.
• Limited Warranty  Guía para rápida consulta (Spanish Quick Use Guide)
- 12 -
- 11 -
Si no puede resolver su problema, por favor comunicarse al Centro de 
llamadas del Cliente para asistencia del producto al 1-800-211-PANA(726\
2).
Para localizar un centro de servicios autorizado, llame sin costo al 
1-800-211-PANA(7262) o envie un correo a : consumerproducts@panasonic.\
com
Spanish Quick Use Guide/ Guía para rápida consulta
ANTES DE AL SERVICIO SOPORTE TÉCNICO
Spanish Quick Use Guide/ Guía para rápida consulta Guía para rápida consulta (Spanish Quick Use Guide)  Location o\
f Controls (Multi Function Display, Rear View of the VCR)
- 10 -
OPERACIONES BÁSICAS PARA 
LA REPRODUCCIÓN
Detalles especiales durante la grabación
Presione FF  o REW  para búsqueda de
escenas hacia delante/ hacia atr ás.
Presione PLAY  para liberar.
Luego de que la b úsqueda se ha iniciado,
cada vez que  presione FF o REW  se
cambia la velocidad como sigue: 
[SLP] aprox. 21X  ↔↔
↔↔
↔ aprox. 9X
[LP] aprox. 9X  ↔↔
↔↔
↔ aprox. 7X
[SP] aprox. 7X  ↔↔
↔↔
↔ aprox. 3X
Si la im ágen se interrumpe con la velocidad de
21x, 9x o 7x, cambie la velocidad a 9x, 7x o 3x.
Presione PAUSE/SLOW  para imagen
Fija (Congelada). 
Presione PLAY  para liberar.
Presione PAUSE/SLOW  en el modo
de Imagen fija para im ágenes cuadro a
cuadro.  Presione PLAY  para liberar.
Mantenga  pulsado PAUSE/SLOW  en
el modo de imagen fija para im ágenes
en c ámara lenta.
Presione PLAY  para liberar.
Presione EJECT  en el control remoto, o
STOP/EJECT  en el VCR para expulsar
el cassette. 
Presione REW  o FF  en el modo de
parada para rebobinado/avance r ápido
del cassette.
Grabación de un toque .
Presione REC  repetidamente para ajustar
la duraci ón de la grabaci ón como sigue:
como sigue: 30 min.  
➛➛
➛➛
➛  1 hr  
➛➛
➛➛
➛  1:30hr  
➛➛
➛➛
➛
2:00   
➛➛
➛➛
➛  3:00  
➛➛
➛➛
➛  4:00  
➛➛
➛➛
➛  Salida.
La VCR se apagara autom áticamente en en
intervalo seleccionado de tiempo.
1Inserte una cassette ,la alimentaci ón del VCR se activa.
En la Pantalla de Visualizaci ón Multi
Funci ón se ilumina  “VCR ”.
2Presione PLAY  para reproducir el
cassette.
 Si el cassette no tiene leng üeta de
prevenci ón de grabaci ón (p. 3), se inicia la
reproducci ón autom áticamente.
3Presione STOP  para detener el
cassette.
OPERACIONES BÁSICAS PARA 
LA GRABACIÓN
1Inserte el cassette con lengüeta de 
protección de grabación (p. 3).
 La alimentaci ón del VCR se activa.
En la pantalla Multi Funci ón se ilumina
“ VCR ”.
2Presione CH , o  las teclas de
números  para seleccionar el canal.
3Presione SPEED  para seleccionar la
velocidad de grabaci ón (p. 3)
 SP = Reproducci ón est ándar,
 LP = Larga duraci ón,
  SLP = Superlarga duraci ón.
4Presione REC  para comenzar a grabar.Para eliminar escenas indeseadas, 
presione PAUSE/SLOW  para pausar, y al
presionar nuevamente se reanuda la
grabaci ón.
5Presione STOP  para detener la
grabaci ón.
Ver un canal y grabar otro. 
Presione VCR/TV.
(La indicaci ón VCR se apagara en la
“ visualizaci ón de Multi-Funci ón”)
➛➛
➛➛
➛ Seleccione canales de TV (Mientras
permanece grabando)
Seleccione canales con VCR. 
Presione VCR/TV  (la indicación  “VCR ” se
encender á en la vizualizaci ón multi-funci ón)
➛➛
➛➛
➛ Seleccione canales en su VCR.
PROGRAMACIÓN FÁCIL PARA 
LA GRABACIÓN CON
TEMPORIZADOR
1
Presione  para seleccionar  un
n úmero que no est á usando para
ingresar mas programas y  presione 
para ajustar. Luego repita el paso 2.
Presione nuevamente 
PROG para salir.
Presione PROG
 para finalizar el
programa.
Fecha de hoy
Orden para elegir
Ejemplo
2) Para los ajustes siguientes,presione  para seleccionar y
presione   para ajustar los tiempos
de INICIO/PARADA, CANAL, o 
entrada de LINEA, y velocidad del
cassette (SP, LP, SLP).
Presione POWER off  para ajustar el
temporizador.
(Se ilumina  “TIMER ” en el panel delantero)
2 
3 
41) Para ajustar la FECHA de
grabación, presione  para
seleccionar: 1-31 = una vez, o DIARIO = a la misma 
hora de lunes a viernes,
o SEMANA = a la
misma hora cada
semana y presione 
para ajustar.
REVISIÓN, REEMPLAZO O 
BORRADO DE PROGRAMACIONES
(no se puede efectuar durante la grabación)
a
b 
c1) Presione PROG. 
2) Presione    para seleccionar la
linea.
Presione 
 para
seleccionar programa 
deseado.
Para reemplazar programa... 1) Presione 
 para
desplegar menu.
2) Repita paso 2 (ver 
arriba) para introducir
el nuevo programa.
Para cancelar programas… Presione ADD/DLT
dPresione PROG  Para terminar
programacion.
PARA CANCELAR LA GRABACIÓN 
CON TEMPORIZADOR
(la grabación está teniendo lugar)
Presione POWER  y luego STOP dentro
de los 10 segundos para cancelar la 
grabaci ón con temporizador (el indicador
TIMER se apagar á en la Pantalla de Multi-
Funci ón)
1) Presione PROG
.
2) Presione 
  para visualizar la
pantalla de Programaci ón.
DIARIO7 2
1
31
68    9
     /      Orden para elegir
SEMANAL(SAB)SEMANAL(LUN)SEMANAL(DOM)
FE     I N I C     PARADA   CA  VEL7      2 : 00 P      3 : 20 P    02  SLP-- -- : --       -- : --    --  --
-- -- : --       -- : --    --  --
-- -- : --       -- : --    --  --CANCELAR: ADD / DLT ELEGIR    :            FIJAR :SAL I R       : PROG
       PROG.                 L I STA
       PROG.                 L I STAFECHA I N I C I O
PARADACA
SLP
ELEGIR  FECHA  DE  I N I C I O
  7  SAB  --:--  --:--   --HOY
ELEGIR
     :           FIJAR : 
TERMINAR : PROG     
FE     I N I C     PARADA   CA  VEL7      9 : 00 A    12 : 00 A    08    SP8    10 : 00 P    12 : 00 P    02    SP10    8 : 00 P      9 : 00 P    10    SPSU   9 : 00 P    10 : 00 P    L1    LP
       PROG.                 L I STA
CANCELAR: ADD / DLT ELEGIR    :            FIJAR :SAL I R       : PROG
       PROG.                 L I STAFECHA I N I C I O
PARADACA
SLP
ELEGIR  FECHA  DE  I N I C I O
  7 SAB     9:00A 12:00A   08HOY
ELEGIR
     :           FIJAR : 
TERMINAR : PROG     
FE     I N I C     PARADA   CA  VEL--  -- : --        -- : --    --   --8    10 : 00 P    12 : 00 P    02    SP10    8 : 00 P      9 : 00 P    10    SPSU   9 : 00 P    10 : 00 P    L1    LP
       PROG.                 L I STA
CANCELAR: ADD / DLT ELEGIR    :            FIJAR :SAL I R       : PROG
VCR
VHF/UHFEstuche convertidor  
de TV por cable
Televisor
Terminal 
IN FROM ANT.
Entrada (IN) desde
ANT./CABLE
Terminal 
OUT TO TV
Terminal IN FROM ANT.
Televisor VCR
VHF/UHF Terminal  
OUT TO TVEntrada (IN) desde
ANT./CABLE
Spanish Quick Use Guide/ Guía para rápida consulta
- 9 -
CONEXIONES
Conecte el cable de la antena al 
terminal IN FROM ANT del VCR.
Conecte el terminal OUT TO TV
del VCR a la entrada de la antena 
VHF/UHF del TV con el cable RF 
incuido.
Para Ant/Cable ➛➛
➛➛
➛ VCR ➛➛
➛➛
➛ TV
Para Sistema Digital de Satelite (DSS)/ Convertidor de cable ➛➛
➛➛
➛ VCR ➛➛
➛➛
➛ TV
Conecte la salida de convertidor 
de cable al terminal IN FROM 
ANT.
Conecte el terminal OUT TO TV 
del VCR a la entrada de la antena 
VHF/UHF del TV con el cable RF 
incluido.
1
2
1
2
Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA.La videograbadora iniciar á autom áticamente la fijaci ón de los canales y del reloj al enchufar el cable de CA.
1Encienda el TV y cambie al canal 3.
2Enchufe el cable de CA. 
La videograbadora se encenderá e
iniciará las fijaciones de los canales y 
del reloj.
 Si no aparece la pantalla de abajo, 
compruebe la conexi ón del VCR-TV y
si el canal del TV est á a 3, intennte
cambiando al canal 4.
 Para cambiar el canal de salida del
VCR, consulte las instrucciones de
“Canal de salida del VCR ” en la p ágina
12 de las operaciones avanzadas.
Si est á usanndo un convertidor de TV por
cable y en su area hay un canal de Public
Broadcast Station (PBS), ajuste su
convertidor al canal PBS de su area. 
Si est á usando un receptor DSS, este debe
estar apagado.
CONFIGURACIÓN INICIAL
3Las fijaciones se realizan 
automáticamente. Cuando termina las
fijaciones, aparecerá la siguiente 
pantalla.
Si aparece en la pantalla “FIJACION
AUTOMATICA DEL RELOJ ES 
INCOMPLETO”, Ajuste el reloj como
se describe a continuación.
AJUSTE MANUAL DEL RELOJ
Si la fijaci ón ha sido incompleta.
1Presione la tecla ACTION en el 
control remoto para visualizar la 
pantalla del menú RELOJ.
2Presione   para seleccionar el mes
y  para ajustar. De la misma forma,
seleccione y ajuste la fecha, año, 
hora y DST (Hora de Verano).
3Presione dos veces la tecla ACTION 
para poner el RELOJ en marcha y 
salir.
2
1
2
1
CONEXIONES/CONFIGURACIÓN INICIAL (READY TO PLAY)
VCR         RELOJ        CANAL
FIJACION  ES  COMPLETO
VERANO : ACT9 /29 / 20 0 2  DOM   2 : 20PM
F I J A R       :         I N I C I AR : ACT I ON     
VCR         RELOJ        CANAL
ELEGIR  MES
VERANO : ACT1 /     /:
ELEGIR  :              FIJAR : 
SALIR       : ACT I ON     
Panasonic Consumer Electronics Company, 
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094 
Panasonic Sales Company (“PSC”), 
Division of Matsushita Electric of Puerto Rico, Inc. 
Ave. 65 de Infanter ía. Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Printed in Indonesia LSQT0532B
S1101-1052
P
Rear View of the VCR
OUT
IN 1
OUT TO TVVIDEO
AUDIO
IN FROM ANT.
     VHF/UHF
VHF/UHF Antenna 
Input Terminal
VHF/UHF Antenna
Output Terminal
Video Output
 Connector Audio Output
Connector
Audio Input ConnectorVideo Input Connector
VCR Indicator 
Lights up when the
VCR/TV selector is
set to VCR.
Power Indicator 
Lights up when power is on.
Clock/ Status/ Channel/ Speed Display
Displays the current time. Briefly displays VCR status
when a function button is pressed.
Briefly displays the channel number, or  “L1 ” or  “L2 ”
when a channel or line input is selected.
Briefly displays the recording speed when SPEED is 
pressed.
Multi Function Display
Timer Indicator 
Lights up when the VCR is set for a Timer
Recording, or when One Touch Recording
(OTR) is used.
Flashes when a Timer Recording is set, but a
tape has not been inserted into the VCR.
Location of Controls
- 8 -
AC Power Plug 
While plugged into an AC outlet, the
VCR consumes 2.5 W of electrical 
power in off condition.
Note to CABLE system installerThis reminder is provided to call the CABLE system installer ’s attention to Article 820-40 of the
NEC in USA (and to the Canadian Electrical Code in Canada) that provid\
es guidelines for proper 
grounding and, in particular, specifies that the cable ground shall be c\
onnected to the grounding
system of the building, as close to the point of cable entry as practica\
l.
ALIMENTACIÓN DE AC
La unidad no enciende ….
GRABACIÓN Y REPRODUCCIÓN
(REC / PLAY)
No se pueden grabar programas de TV 
No se puede efectuar grabaci ón con
temporizador …
No hay imagen de reproducci ón, o la
imagen de reproducci ón tiene ruidos
o contiene rayas... 
En la reproducci ón de efectos
especiales, la imagen puede contener 
algunos saltos verticales cuando se
utiliza un televisor con Control de
Bloqueo Vertical Autom ático...
No se puede controlar el VCR...
Verifique los siguientes puntos una y otra ves si  esta teniendo problem\
as con su VCR.
(BO : Haga referencia en la instruciones de funcionamiento [Operaciones\
 B ásicas])
(AO : Haga referecncia el la instruciones de funcionamiento [Operacione\
s Avanzadas])
CORRECCIÓN
 Revise que el cordon de alimentaci ón de AC este correctamente
conectado a la toma de pared.
 Presione el bot ón  “POWER ” para el encendido de la unidad.
 Verifique que la fuente de alimantaci ón est á activada.
Varios
No se pueden ver los programas en 
el televisor... 
No se puede introducir la cassette de 
vídeo...
No se puede extraer la cassette de 
v ídeo...
La cassette de v ídeo es expulsada al
dar comienzo a una grabaci ón o al
desactivar la alimentaci ón para la
grabaci ón con teporizador...
En el modo de Detenci ón, el motor
(CILINDRO) sigue girando...
CONTROL REMOTO
NO funciona el control remoto... 
Los botones  “ACTION ” y/o  “PROG ”
no responden...
CORRECCIÓN
 Revise las conexiones entre VCR, antena externa o cable y TV.
 Verifique la selecci ón de conexiones (BO p. 4, AO p. 3)
 Verifique que su sistema de antenna (Cable o TV) est én
correctamente seleccionados. Vea  “Channels ” (AO p. 12).
 Aseg úrese  que la pesta ña en el cassette de grabaci ón est é
intacta (BO p. 3).
 Compruebe que el reloj ha sido ajustado a la hora y fecha actual.
 Aseg úrese de que la caja de Cable/DSS (si se utiliza) se
deja encendido y est á sintonizado al canal a grabar.
 Ajuste las horas de comienzo y deteci ón de grabaci ón
correctamente. (BO p. 6)
 Aseg úrese de que ha apagado el VCR antes de la grabaci ón.
(BO p. 6)
 La grabaci ón con temporizador quiz ás no pueda realizarse o
continuarse si se produjera una interrupci ón de corriente antes
o durante una grabaci ón con temporizador, incluso despu és de
restablecido el fluido el éctrico.
 Selecci óne el canal 3 o 4 en el televisor, de modo que
corresponda con el canal de salida del videograbador (3 o 4) 
(BO p. 4), o seleccione LINE.
 Ajuste el selector VCR/TV a  “VCR ”.
 Ajuste el control TRACKING en una de las dos direcciones. (BO p. 3)
 Pruebe a realizar la limpieza de cabezales.  (BO p. 3)
 Ponga el Control de Bloqueo Vertical del televisor en
“MANUAL ”  y luego realice el ajuste.
 Aseg úrese de que el aparato est á encendido.
 Revise las pilas del control remoto.
 Aseg úrese de que el BLOQUEO DEL VCR est é ajustado a
INACTIVO (AO p. 10)
 Aseg úrese de que no est á funcionando una grabaci ón con
temporizador.
CORRECCIÓN
 Aseg úrese de que el aparato est á encendido.
 Aseg úrese de que el control remoto est á en le modo de VCR.
 Apunte el control remoto derectamente al sensor remoto del 
VCR. (BO p. 7)
 Evite que ning ún objeto interrumpa la se ñal del control remoto.
 Revise las pilas del control remoto (BO p. 3)
 Aseg úrese de que el BLOQUEO DEL VCR est é ajustado a
INACTIVO (AO p. 10)
 Si ei sensor remoto recive directamente la lus del fluorescente o luz
solar puede causar interferencia con la se ñal del control remoto.
 Verifique las conexiones entre VCR, cable o antena y TV.
 Presione el bot ón VCR para el modo de  “VCR ”. (AO p. 2)
 Revise las baterias del control remoto. (BO p. 3)
CORRECCIÓN
Aseg úrese que la TV este encendida.
 Aseg úrese que la TV est é conectado a la salida de la VCR
(VCR Out).
 Verifique conexiones entre VCR,cable o antena y TV.
 Ajuste el selector VCR/TV a  “TV ”. (BO p. 5)
 Aseg úrese que la apropiada se ñal fue seleccionada.
 Inserte el cassette con el lado de la ventana hacia arriba y la 
pesta ña de grabaci ón frente a usted.
 Verifique que no tenga ning ún cassette dentro del aparato.
 Inserte o conecte completamente el cable de alimentaci ón de
AC a la toma de pared.
 Aseg úrese que la pesta ña de grabaci ón del cassette este
intacta. (BO p. 3)
 Para activar r ápidamente el mecanismo de reproducci ón, el
cilindro sigue rotando durannte 3 minutos. Esto disminuye el 
tiempo de respuesta desde la parada hasta la reroducci ón o
hasta la el modo de b úsqueda en rebobinado.
Enchufe el cable de CA.
PRECAUCIÓN 
Al usar cables coaxiales RF del tipo  “tuerca ”,
apri ételos solamente con los dedos. Un apriete
excesivo puede da ñar los terminales.
Limited Warranty
Panasonic VHS VCR Products
Limited Warranty
Limited Warranty Coverage 
If your product does not work properly because of a defect in materials \
or workmanship, Panasonic 
Consumer Electronics Company or Panasonic Sales Company (collectively r\
eferred to as  “the
warrantor ”) will, for the length of the period indicated on the chart below, whic\
h starts with the date of
original purchase ( “warranty period ”), at its option either (a) repair your product with new or refurbish\
ed
parts, or (b) replace it with a new or a refurbished product. The deci\
sion to repair or replace will be 
made by the warrantor. 
During the  “Labor ” warranty period there will be no charge for labor. During the  “Parts ” warranty period,
there will be no charge for parts. You must mail-in your product during \
the warranty period. 
If non-rechargeable batteries are included, they are not warranted.
This warranty only applies to products purchased and serviced in the Uni\
ted States or Puerto Rico.
This warranty is extended only to the original purchaser of a new produc\
t which was not sold  “as is ”.
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please shi\
p the product to: Panasonic Services Company 
Customer Servicenter Suite B 
4900 George McVay Drive
McAllen, TX 78503
For assistance in Puerto Rico call Panasonic Sales Company
(787) 750-4300 or fax (787)768-2910 
When shipping the unit carefully pack and send it prepaid, adequately in\
sured and preferably in the original 
carton. Include a letter detailing the complaint and provide a day time \
phone number where you can be
reached.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE REQ\
UIREDTO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE\
,AMOUNT PAID AND PLACE OF PURCHASE.CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCHPROOF OF PURCHASE.
PANASONIC CONSUMER ELECTRONICS COMPANY, 
DIVISION OF MATSUSHITA ELECTRIC 
CORPORATION OF AMERICA 
One Panasonic Way 
Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, 
DIVISION OF MATSUSHITA 
ELECTRIC OF PUERTO RICO, INC., 
Ave. 65 de Infanter
ía, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
Limited Warranty Limits And Exclusions 
This warranty ONLY COVERS failures due to defects in materials or workma\
nship, and DOES NOT
COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NO\
T COVER damages 
which occurred in shipment, or failures which are caused by products not\
 supplied by the warrantor, or 
failures which result from accidents, misuse, abuse, neglect, mishandlin\
g, misapplication, alteration,
faulty installation, set-up adjustments, misadjustment of consumer contr\
ols, improper maintenance,
power line surge, lightning damage, modification, introduction of sand, \
humidity or liquids, commercial
use such as hotel, office, restaurant, or other business or rental use o\
f the product, or service by anyone
other than a Factory Servicenter or other Authorized Servicer, or damage\
 that is attributable to acts of
God. 
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRA\
NTY 
COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIA\
L 
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BR\
EACH 
OF THIS WARRANTY.  (As examples, this excludes damages for lost time, cost of having someo\
ne
remove or re-install an installed unit if applicable, travel to and from\
 the servicer, loss of or damage to
media or images, data or other recorded content. The items listed are no\
t exclusive, but are for
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF
MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY. 
Some states do not allow the exclusion or limitation of incidental or co\
nsequential damages, or 
limitations on how long an implied warranty lasts, so the exclusions may\
 not apply to you. 
This warranty gives you specific legal rights and you may also have othe\
r rights which vary from state to 
state. If a problem with this product develops during or after the warra\
nty period, you may contact your
dealer or Servicenter. If the problem is not handled to your satisfactio\
n, then write to the warrantor ’s
Consumer Affairs Department at the addresses listed for the warrantor. 
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE Y\
OUR 
RESPONSIBILITY.
Customer Services Directory
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate yournearest servicenter by visiting our Web Site.
For Product Information, Operating Assistance, Literature Request, Deale\
r Locations,and all Customer Service inquiries please contact:
1-800-211-PANA (7262), Monday-Friday 9 am-9 pm; Saturday-Sunday 9 am-7 pm, EST.
or send e-mail : [email protected]
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factor\
y Servicenter: Ave. 65 de Infanter ía, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300  Fax (787)768-2910
1-800-332-5368 (Customer Orders Only) 
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday;  6 am to 10:30 am Saturday; PST)
(Visa, MasterCard, Discover Card, American Express, Check)
Accessory Purchases:
As of April 2002
Product or Part Name
All components of VCR except 
item listed below 
Video Tape (in exchange for 
defective video tape)
Parts
One (1) Year
Five (5) Days Labor
Ninety (90) Days
Not Applicable
VCR         CLOCK     CHANNEL
AUTO  CLOCK  SET 
     
     PROCEEDING
CANCEL   : STOP
VCR         CLOCK     CHANNEL
CH  AUTO  SET  PROCEEDING
CANCEL   :
 STOP
VCR         CLOCK     CHANNEL9 /29 / 20 0 2  SUN    2 : 20PMDST : ONSETT I NG  :   CH   10
AUTO  CLOCK  SET 
     COMPLETED
AUTO  CLOCK  SET  IS 
INCOMPLETE
PLEASE  SET  CLOCK BY
PRESSING  ACTION KEY VCR         CLOCK     CHANNEL
Cambie el idioma 
luego de la fijaci
ón
inicial (para su
ayuda vea la
p ágina 12 de las
operaciones
avanzadas.)
PV402 Basic-1 (02-5-7) 2nd.p65 2002/05/08, 13:48
1
LSQT053 2B(Basic Operations) - Front 
						

							• Timer Recording  Location of Controls (Remote Control Buttons, Front View of the VCR)
COMMERCIAL SKIP/ 
ZERO SEARCH
(Starts COMMERCIAL SKIP/ Zero Search)
INPUT(For LINE or channel)
POWER(Turns VCR off/on)
PLAY (Plays a tape)/FAST FORWARD/SEARCH(Fast forwards tape/ forward visualsearch)
REWIND/SEARCH(Rewinds tape/ reverse visualsearch)
STOP (Stops tape)
CHANNEL  / TRACKING/ V-LOCK(Selects channel/ reduces
picture noise during Play and
Slow mode)
Remote Control Buttons
VCR/TV(For TV or VCR mode)
SPEED(Changes tape speed)SEARCH/ ENTER(Set search system /Tunes TV channel)
NUMBER Keys(Selects channel directly)
TV (mode)(Enables TV functions)
TAPE POSITION(Locates tape position)
EJECT(Ejects tape)
ACTION(Displays menu)
PAUSE/SLOW(Displays still, frame by frame,or slow motion picture)
COUNTER RESET(Resets counter to zero)
RECORD(Records a program, etc.)
ADD/DELETE(Adds or deletes a channel)
VCR (mode)(Enables VCR functions)
VOLUME +/-(Adjusts TV volume)
DISPLAY(Displays VCR status)
Location of Controls
PROGRAM(Displays Timer Program screen)
Front View of the VCR
RECORD
STOP/EJECT
Cassette Compartment
POWER
REWIND/ 
SEARCH
PLAY
CHANNEL 
  / 
TRACKING/ V-LOCK
Remote 
Sensor
FAST 
FORWARD/
SEARCH
Video
Input
Connector
Audio Input 
Connector
EJECT button:Press to eject tape. EJECT is not available during recording.
*
Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
- 7 -
PLAY, STOP, REW, and FF 
function as  operation keys when menus 
are displayed.
  Remote keys
Timer Recording
11) Press PROG*.
2) Press 
  to display program screen.
Press PROG  to end programming.
2
2) Set remaining items,
press  to select and
press  to set START/ STOP times, CH(channel) or
LINE input (p. 9 of “Advanced Operations” book), and 
tape speed (p. 3).
1) Set record DATE,
press 
 to select:
1~31= one time, 
or DAILY= MON~ FRI, 
or WEEKLY= same time 
each week and  press 
.
3To Enter More Programs 
Press  to select and
press 
 to set an unused program.
Then repeat step 2. 
Or,  press PROG  to exit.
Timer Recording
Example
Today
Press   to select
desired program.
4Press POWER off  to set the timer recording. (“TIMER” lights on Multi Function Di\
splay.)
(Recording is not in progress)
a1) Press PROG.
2) Press 
   to select LIST.
b
c
To Replace program...
dPress PROG  to end the programming.
• If you are using a Cable Box, VCR Timer Programming Channel (Step 2 above) must be set to the Cable Box output channel and your Cable Box must be manually set to 
the desired channel. The Cable Box must be left on.
 If a power interruption occurs while programming the timer, the timer program(s) may be canceled. If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears
on-screen, please re-enter the timer programs.
Important notes when using DSS receiver
 When recording programs via DSS receiver, DSS receiver must be left on. 
 When recording programs via an antenna or cable, DSS receiver must be tu\
rned off.
Review, Replace, or Clear Program
1) Press  to display.
2) Repeat Step 2 
(above) to set new
programs.
Press ADD/DLT .
or
To Clear program...
Press POWER and then STOP within 10
seconds to cancel the Timer Recording. 
(The TIMER indicator goes out on Multi 
Function Display.)
Cancel a Timer Recording
(Recording is in progress)
- 6 -
Notes
DAILY7 21
31
68    9
SELECT     /      Selection Order
WEEKLY
(SAT)WEEKLY(MON) WEEKLY
(SUN)
TIMER  PROG.           L I ST
CANCEL   : ADD / DLT SELECT   :              SET :EXIT         : PROG
DT   START     STOP    CH   SPD  7     9 : 00A  12 : 00A   08      SP  8   10 : 00P  12 : 00P    02     SP10     8 : 00P     
     9 : 00P   10     SP
SU     9 : 00P   10 : 00P    L1     LP
TIMER PROG.          LIST
SELECT START DATE
DATE START
STOPCH
SP
TODAY  7  SUN  9:00A 12:00A  08
SELECT  :             END        : PROG SET:
TIMER  PROG.           L I STDT   START     STOP    CH   SPD13     2 : 00 P    3 : 20P   02    SLP--  -- : --    -- : --   --   --
--  -- : --    -- : --   --   --
--  -- : --    -- : --   --   --CANCEL   : ADD / DLT SELECT   :              SET :EXIT         : PROG
SELECT  :             END        : PROG 
DATE START STOPCH
SLP
SET:SELECT START DATE TODAY13  SAT  --:--  --:--   --
TIMER PROG.          LIST
TIMER  PROG.           L I ST
CANCEL   : ADD / DLT SELECT   :              SET :EXIT         : PROG
DT   START     STOP    CH   SPD--  -- : --    -- : --   --   --  8   10 : 00P  
12 : 00P    02     SP10     8 : 00P     9 : 00P   10     SP
SU     9 : 00P   10 : 00P    L1     LP
 Connections  Initial Setup  Clock Set  Select Channel  Playback  Record  Auto Operation
This video recorder, equipped with 
HQ (High Quality) system, is 
compatible with existing VHS
equipment. Only use tapes with the
 mark. Only tapes tested and
inspected for use in 2, 4, 6, and 8 
hour machines are recommended.
* Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
- 5 -
1Insert a tape with a record tab  (p. 3).1Insert a tape.
Special Features During Play
2Press CH  or NUMBER keys
to select the channel. For “LINE” input, see p. 9 of “Advanced Operations” book.
 If recording from a channel over 100, first press 100 key then the other 2 digits.
3Press SPEED 
to select record speed (p. 3).
4Press REC
to start recording.
 To edit,  press PAUSE/SLOW  to pause,
and again to resume recording.
5Press STOP  to stop recording.
2Press PLAY  to play tape. If tape has no rec. tab (p. 3), auto play begins.
One Touch  Recording 
(record in progress)
Press REC repeatedly to set length as follows:
30 min. ➛ 1 hr. ➛ 1:30 ➛ 2:00 ➛ 3:00➛ 4:00 ➛ exit.
The VCR shuts off at the length set.
Record one station, watch anotherPress VCR/TV 
(“VCR” goes out on Multi Function Display),
➛ select channels on TV (recording continues).
Select channels on VCR (in STOP or 
PAUSE mode)
Press VCR/TV 
(“VCR” lights up on Multi Function Display),
➛ select channels on VCR.
Record on a Tape
Forward/Reverse Scene Search 
➛ Press FF  or REW .
➛ Press PLAY  to release.
After search has begun, each additional 
press of FF or  REW  changes speed as
shown below. 
[SLP] : Approx. 21X 
↔ Approx. 9X
[LP] : Approx.   9X ↔ Approx. 7X
[SP] : Approx.   7X ↔ Approx. 3X
If at 21X, 9X, or 7X speed the picture is 
interrupted, change speed to 9X, 7X, or 3X.
Still (Freeze) Picture 
➛ Press PAUSE/SLOW .
➛ Press PLAY  to release.
Frame by Frame Picture 
➛Press PAUSE/SLOW  in Still mode.
➛ Press PLAY  to release.
Slow Motion Picture 
➛Hold down PAUSE/SLOW  in Still mode.
➛ Press PLAY  to release.
Loose or peeling labels 
may cause tape jam.
 These features work best in SP or SLP mode. 
 The sound will be muted.
 To reduce picture noise, see “Manual Tracking Control” on p. 3.
 After VCR is in Still or Slow mode 3 minutes, it auto switches to Stop mode to protect the tape 
and the video heads.
Press REW or FF  in Stop mode  to
Rewind or Fast Forward tape.
Press EJECT  on remote,
or  STOP/EJECT  on VCR to eject  tape.
3Press STOP to stop tape.
Playback a Tape
 Watching one channel and recording
another is not possible when using Cable 
Box or DSS Receiver.
 After 5 minutes in Pause mode, VCR stops to protect the tape and the video heads.
 Picture interruption may occur with some TVs. 
 FF and REW search speed may varydepending on current tape position.
Notes
Playback / Record on a Tape
 Auto Play
Insert a tape ➛ Power comes on ➛ Play starts if there is no record tab (see p. 3).
 Auto Rewind
Play 
Fast Forward
 Play Auto Eject(Repeat Play must be off)Play ➛ Tape end ➛ Rewind ➛ Tape ejects if there is no record tab
Auto Operation Functions
Notes
Notes
➛ Tape end ➛ Rewind
Connections / Initial Setup ( Ready to Play)
Connecting
Connect cable from 
Antenna/Cable to VCR’s IN
FROM ANT. jack.
Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack
with included RF Cable
accessory.
For ANT./Cable ➛➛
➛➛
➛ VCR ➛➛
➛➛
➛ TV
For DSS/Cable Box ➛➛
➛➛
➛ VCR ➛➛
➛➛
➛ TV
Connect your cable box’s 
OUT jack to the VCR’s IN
FROM ANT. jack with an RF
cable.
Connect VCR’s OUT TO TV
jack to TV’s ANT. IN jack
with included RF Cable
accessory.
1
2
1
2
Please make all cable or antenna connections before plugging into the AC 
outlet.
Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.
1Turn TV on and tune to channel 3.
2Plug VCR Power Cord into AC wall 
outlet. VCR comes on and auto 
channel and clock set starts.
WARNING 
Over tightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.
 If screen below does not appear, check
VCR - TV connection and, if TV is 
tuned to channel 3, try switching it to 
channel 4.
 To change VCR’s output channel, please refer to “VCR’s Output Channel” 
in Advanced Operations book (p. 12).
If you use a cable box, turn it on and set it 
to the Public Broadcasting Station (PBS)
channel in your time zone. If you use a
DSS receiver, it must be turned off.
Initial Setup (Ready to Play)
VCR         CLOCK     CHANNEL
AUTO  CLOCK  SET 
     
     PROCEEDING
CANCEL   : STOP
VCR         CLOCK     CHANNEL
CH  AUTO  SET  PROCEEDING
CANCEL   :
 STOP
3Settings are made automatically. 
When setup is done, this screen appears.
VCR         CLOCK     CHANNEL9 /29 / 20 0 2  SUN    2 : 20PMDST : ONSETT I NG  :   CH   10
AUTO  CLOCK  SET 
     COMPLETED
If “AUTO CLOCK SET IS INCOMPLETE” 
appears, manually set clock. 
See below.
Manual Clock Set
If Auto Clock Set was incomplete.
1Press ACTION* on remote to display 
CLOCK menu.
VCR         CLOCK     CHANNEL
SELECT  MONTH
DST:ON1 /     /:
SELECT   :              SET : 
EXIT        : ACT I ON     
2Press   to select the month and 
to set. In the same manner, select and 
set the date, year, time, and DST
(Daylight Saving Time).
3Press ACTION to start clock and exit.
- 4 -
Plugging the AC Power Plug into an AC outlet
VCR         CLOCK     CHANNEL
SET COMPLETED
DST:ON9 /29 / 20 0 2  SUN    2 : 20PM
              START   : ACT I ON     
SET         : 
     
IN FROM ANT.
TV VCR
VHF/UHF OUT 
TO TV IN from
ANT./CABLE1
2
IN FROM ANT.
TV
VCR
VHF/UHF OUT 
TO TV IN from
ANT./CABLE
Cable TV 
Converter Box
1
2
Congratulations
on your new purchase! With proper use, this 
dependable product will provide years of 
enjoyment. Please fill in the information below. 
(Serial number is on tag on back of VCR.)
Before Using
RF Coaxial 
Cable
VJAS0196
Batteries 2 
“AA ”Remote Control
LSSQ0263
Accessories
To order accessories, call toll free 
1-800-332-5368.
Loading the Batteries
Date of Purchase
 Dealer Purchased From
 Dealer Address
 Dealer Phone No.
 Model No. PV-V402
 Serial No.
    Battery replacement caution Do not mix old and new batteries.
 Do not mix alkaline with manganese batteries.
Only use tapes with the  mark in this unit.
Prevent Accidental Tape Erasure
Record/Playback Time
To record again
Break off the tab to 
prevent recording.
SP(Standard Play)2 Hours
40 Minutes
1 Hour 2 Hours
5 Hours
20 Minutes
2 Hours
4 Hours
LP(Long Play)
3 Hours
6 Hours 8 Hours
SLP(Super Long Play)
Type of Video Cassette
Tape Speed
Setting T160T120
T60
Power Source: 120 V AC, 60 Hz
Power Consumption:Power OnApprox. 18 WPower OffApprox. 2.5 W
Video Signal: EIA Standard NTSC color
Video Recording 4 rotary heads helical
System: scanning system
Audio Track: 1 track (Normal)
Tuner: 
Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
CABLE Channels: Midband A ~ I (14 ~ 22) 
Superband J ~ W (23 ~ 36)
Hyperband AA ~ EEE 
(37 ~ 64) 
Lowband A-5 ~ A-1 (95 ~ 99) 
Special CABLE channel 5A 
(01)
Ultraband 65 ~ 94, 100 ~ 125
Operating
Temperature: 5 °C ~ 40  °C (41  °F ~ 104  °F)
Operating Humidity: 10 % ~ 75 %
Weight: 2.5 kg (6.0 lbs).
Dimensions: 360 (W) x 93 (H) x 242 (D) mm 
14-3/16” (W) x 3-11/16 ” (H) x
9-9/16 ” (D) inch
Specifications
Head Cleaning
Use soft, dry cloth or dusting attachment of a 
vacuum to remove dust from all cabinet vent
holes. You may moisten cloth with nonabrasive, 
antistatic cleaner/ polisher. 
Caution
:
Alcohol and various solvents could damage finish.
Cleaning the VCR
Note: Designs and specifications are subject to change without notice.
Digital Auto PictureAutomatically controls the video output signal for 
less noise depending on the tape condition.
Digital Auto TrackingContinuously analyzes the signal and adjusts for 
optimum picture quality.
Manual Tracking Control(to reduce picture noise) 
Use during Playback and Slow Motion mode to
reduce picture noise. 
Press CH  (TRACKING) 
/ on the remote
control or on the VCR until the picture clears up. 
To return to Auto Tracking,  press POWER off,
then on again a few seconds later.
V-Lock Control (to reduce picture jitter)
In Still mode,  CH (TRACKING) / operate as a
V-Lock control.
Features for a Quality Picture
 Important Safeguards  Accessories  Head Cleaning  Loading Batteries  Prevent Tape Erasure  Specifications  Record/Playb ack Time
- 3 -
Record Tab
Screw driver Cover the hole 
with cellophane
tape.
Video Head Clog SensorScreen-right appears during 
play if clogging is detected. 
To remove screen, press PLAY. 
 Use “dry” type head
cleaning cassette only. 
(Part No. NV-TCL30PT is recommended.)
 Follow cleaning tape instructions carefully.
Excessive use of tape can shorten head life.
Old or damaged tapes may clog heads.V I DEO  HEADS  MAYNEED  CLEAN I NGPLEASE   I NSERT  HEADCLEAN I NG  CASSETTEOR  REFER  TO  MANUAL
END               : PLAY
RRRRRRRR
INSTALLATION
1 POWER SOURCE CAUTION Operate only from a power source indicated on 
the unit or in this manual. If necessary, have
your Electric Utility Service Company or Video
Products Dealer verify the power source in your
home.
2 POLARIZED OR GROUNDING PLUG As a safety feature, this Video product comes
with either a polarized power cord plug (one 
blade is wider than the other), or a three-wire 
grounding type plug.
POLARIZED PLUG CAUTION: 
This plug will only fit into an outlet one way. If you 
cannot fully insert the plug, try reversing it. If it still
will not fit, have an electrician install the proper wall 
outlet. Do not defeat the safety feature by tampering 
with the plug.
GROUNDING PLUG CAUTION: 
This plug will only fit into a three-hole grounding 
outlet. If necessary, have an electrician install the 
proper outlet. Do not defeat the safety feature by 
tampering with the plug. 
3 POWER CORDMake sure power cords are routed so that they 
are not likely to have anything rest on them, roll
over them, or be in the way of walking traffic.
If an extension cord is used, make sure it also
has either a polarized or grounded plug and that 
the cords can be securely connected. Frayed 
cords, damaged plugs, and damaged or cracked
wire insulation are hazardous and should be
replaced by a qualified service technician. 
Overloaded outlets and extension cords are fire 
hazards and should be avoided.
4 DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat
generated during operation. If they are blocked,
heat build-up inside the unit can cause failures
that may result in a fire hazard or heat damage
to cassettes. For protection, follow these rules: 
a. Never cover ventilation slots or the unit while
in use, or operate the unit when placed on a 
bed, sofa, rug, or other soft surface.
b. Avoid built-in installation, such as a book case or rack, unless proper ventilation is
provided.
5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES
Do not place the unit over or near any kind of
heater or radiator, in direct sunlight, inside a
closed vehicle, etc.. Do not move the unit
suddenly between areas of extreme temperature 
variation. If the unit is suddenly moved from a 
cold place to a warm place, moisture may
condense in the unit and on the tape.
6 TO AVOID PERSONAL INJURY Do not place unsecured
equipment on a sloping
surface.
 Do not place this unit on any
support that is not firm, level,
and adequately strong. The
unit could fall causing serious
injury to a child or adult and 
damage to the unit.
 An appliance and cart combination should be 
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance 
and cart combination to overturn.
 Carefully follow all operating instructions and 
use the manufacturers recommended
accessories when operating this unit or
connecting it to any other equipment.
FOR YOUR SAFETY, READ AND RETAIN 
ALL SAFETY AND OPERATING 
INSTRUCTIONS. HEED ALL WARNINGS IN 
THE MANUAL AND ON THE UNIT
USING THE VIDEO UNIT
If the unit has been in storage or moved to a new location, refer 
first to the INSTALLATION section of these safeguards.
1 KEEP THIS VIDEO UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2 IF EQUIPMENT IS EXPOSED TO RAIN,  MOISTURE, OR STRONG IMPACT,  unplug the unit and have it inspected by
a qualified service technician before use.
3 DURING AN ELECTRICAL STORM During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time, 
disconnect all equipment from the power source as well as 
the antenna and cable system.
4 WHEN THE UNIT IS PLUGGED IN Never expose the unit to rain or water. DO NOT
OPERATE if liquid has been spilled into the unit.
Immediately unplug the unit, and have it inspected by a
service technician. Fire and shock hazards can result from 
electrical shorts caused by liquid contact inside.
 Never drop or push any object through openings in the
unit. Some internal parts carry hazardous voltages and 
contact can cause electric shock or fire hazard.
 Avoid placing the unit directly above or below your TV set
as this may cause electrical interference. Keep all
magnets away from electronic equipment.
5 USING ACCESSORIES Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING THE UNIT Unplug the unit. Then, use a clean, dry, chemically
untreated cloth to gently remove dust or debris. DO NOT
USE cleaning fluids, aerosols, or forced air that could over-
spray, or seep into the unit and cause electrical shock. Any 
substance such as wax, adhesive tape, etc. may mar the 
cabinet surface. Exposure to greasy, humid, or dusty areas
may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE THIS PRODUCT YOURSELF If, after carefully following the detailed operating instructions,
this Video product does not operate properly, do not attempt 
to open or remove covers, or make any adjustments not 
described in the manual. Unplug the unit and contact a
qualified service technician.
2 IF REPLACEMENT PARTS ARE REQUIRED Make sure the service technician uses only parts specified
by the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized 
substitutes may result in fire, electric shock, or other 
hazards.
3 HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacture ’s service literature to ensure that the
video unit is in safe operating condition. OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges. 
Section 810 of the National 
Electrical Code, ANSI/NFPA
70 (in Canada, part 1 of the
Canadian Electrical Code)
provides information with 
respect to proper grounding 
of the mast and supporting
structure, grounding of the
lead-in wire to an antenna discharge unit, size 
of grounding conductors, location of antenna discharge unit, 
connection to grounding electrodes and requirements for the
grounding electrode.
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away
from power lines, electric light or power circuits and where it
will never come into contact with these power sources if it 
should happen to fall. When installing an outside antenna, 
extreme care should be taken to avoid touching power lines,
circuits or other power sources as this could be fatal.
Because of the hazards involved, antenna installation should 
be left to a professional.
Important Safeguards and Precautions
GROUND  
CLAMP
ELECTRIC
SERVICE
EQUIPMENT ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC- NATIONAL 
  ELECTRICAL CODE
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or\
 moisture.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully \
insert. Avertissement: Afin de pr évenir tout risque d ’incendie ou de chocs  électriques, ne pas
exposer cet appareil  à la pluie ou  à une humidit é excessive.
Attention: Pour  éviter les chocs  électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu ’au fond.
FCC Warning: Any unauthorized changes or modifications to this equipment would void t\
he user’s authority to operate.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
RISK OF ELECTRIC SHOCKDO NOT OPENCAUTION
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated 
voltage within the unit may have sufficient 
magnitude to cause electric shock. Therefore, 
it is dangerous to make any kind of contact
with any inside part of this unit. 
This symbol alerts the user that important 
literature concerning the operation and 
maintenance of this unit has been included. 
Therefore, it should be read carefully in order 
to avoid any problems.
- 2 -
Built-in Head Cleaner
A clean video head helps produce a clear 
picture.So, we have equipped your VCR with a 
built-in, non-chemical head cleaning system that 
helps prevent clogging of the video heads.
Cleaning is performed each time you load or
unload a video cassette. 
 This feature is preventative only, If your video 
heads are seriously clogged, consider the use
of a chemical non-abrasive head cleaning kit 
or take your VCR to a Service Center.
VCR/TV
AUTO  CLOCK  SET  IS 
INCOMPLETE
PLEASE  SET  CLOCK BY
PRESSING  ACTION KEY VCR         CLOCK     CHANNEL
PV402 Basic-2 (02-5-7) 2nd.p65
2002/05/08, 15:10
3
LSQT0532B(Basic Operations) -  Back 
						

							LSQT0533B
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to :\
 [email protected]
Please read these instructions carefully before attempting to connect, 
operate or adjust this product. Please save this manual.
Video Cassette Recorder
Operating Instructions
(Advanced Operations)
For Basic operations, see the separate 
“Basic Operations” instruction book.
Model No. PV-V402
As an ENERGY STAR ® Partner,
Matsushita Electric Corporation of America has determined that this product or productmodel meets the 
ENERGY STAR ®
guidelines for energy efficiency.
Table of Contents
Multi-Brand Control Feature ..................................... 2 
Advanced Connections (Cable/DSS) ....................... 3 
On-Screen Displays (OSD) ...................................... 4 
Warning and Instruction Displays ............................. 5
Tape Operation .................................................... 6, 7 
Copying Your Tapes (Dubbing) ................................ 9 
Special VCR Features ............................................ 10 
Before Requesting Service .................................... 11
Reset Language, Channels, Clock, VCR ’s Output Channel ...12
Reset Language, Channels, Clock, VCR’s Output Channel• Reset Language, Channels, Clock, VCR’s Output Channel  DST
Press ACTION* 
to display MENU.
Language1) Press  to select
language item.
For Spanish 
For French 
For English
Channels
2) Press  to select
“ ANTENNA, ” then
press 
 to set
your antenna system 
( “TV ” or  “CABLE. ”)
 After Channel Auto
Set is finished, Auto
Clock Set will be
performed.
3)
Press 
 to select
“ AUTO SET, ” then
press 
.
 If you use Cable 
Box, set it to the 
PBS channel in your
time zone.
Clock
2) Press  to select
“ MANUAL, ” and  press
. (For Auto Clock Set,
select  “AUTO CLOCK
SET. ”)
( “TIME ZONE ADJUST ”
appears only when 
auto clock is set.)
3) Press  and  to select and set 
the date, time, and
DST (Daylight
Saving Time).
4) Press ACTION  to
start the Clock and 
exit this mode. and 
press 
 to
subtract or add 
hour(s) as necessary.
“ TIME ZONE
ADJUST ” returns to
“ 0 ” if clock is set
manually.
VCR’s Output Channel
After 3 seconds
 To Make Corrections, 
repeat steps 1) ~ 3).
SELECT   :               
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
VCR         CLOCK     CHANNEL
SEL.       :            REGLER:    QUITTER  : ACT I ON     
MAGNETO.     HORL.      CANALREPRISE LECTURE       : NONMESSAGE D ’ ERREUR      : OUICOUPURE AUTO               : NON
LANGUAGE/IDIOMA : FRAN ÇAIS
CA SORTIE : 3
ELEGIR    :            FIJAR :     
SAL I R         : ACT I ON     
VCR         RELOJ        CANALREPETICION                      :INACTAVISO/CONT.REMOTO     :ACT
APAGADO AUTOMATICO :INACTLANGUE/LANGUAGE:ESPA ÑOL
CANAL  DE  SALIDA  :3
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
2) Press   repeatedly.
3) Press  ACTION  to exit. 1)
Press 
  to select
CHANNEL. 1)
Press   to select
CLOCK.
Time Zone 
Adjust
1) Press   to select
CLOCK.
(Only when Auto Clock 
is set.) 
2)
Press 
 to select
“ TIME ZONE
ADJUST ”
3) Press ACTION .
Add or Delete a Channel
To add channel: 
Select channel with  NUMBER keys and
press ADD/DLT .
To delete channel:
Select channel with  CH 
/ or NUMBER
keys  and  press ADD/DLT .
DST (Daylight Saving Time)
VCR auto adjusts clock for DST. 
Spring (First Sunday in April) 
DST:ON ➛ Sets clock ahead one hour.
Autumn (Last Sunday in October) 
DST:ON  ➛ Turns clock back one hour.
 If your area does not observe Daylight 
Saving Time, select DST:OFF.
 Keep these time changes in mind when 
programming VCR for timer recordings.
1)Press  to select
“ VCR ’S OUTPUT CH. ”
3) Press ACTION .
2)
Press  
.
- 12 -
SELECT   :               
EXIT        : ACT I ON     
ANTENNA  :   CABLE 
AUTO  SETWEAK  SIGNAL   DISPLAY : OFF
VCR         CLOCK     CHANNEL
VCR         CLOCK     CHANNELANTENNA  :   CABLE 
AUTO  SETWEAK  SIGNAL   DISPLAY : OFF
SELE
CT   :            SET : 
EXIT        : ACT I ON     
VCR         CLOCK     CHANNEL
CH  AUTO  SET  PROCEEDING
CANCEL   : STOP
VCR          CLOCK    CHANNELAUTO  CLOCK  SET 
MANUALTIME   ZONE  ADJUST   :  0 
SELECT   :               
EXIT        : ACT I ON     
VCR         CLOCK     CHANNEL
SELECT HOURDST:ON9 /29 / 20 
20 0 2  
  SUN  
SUN    2 
  2 : --PM
SELECT   :            SET : 
EXIT        : ACT I ON     
VCR          CLOCK    CHANNELAUTO  CLOCK  SET 
MANUALTIME   ZONE  ADJUST   :  0 
SELE
CT   :            SET : 
EXIT        : ACT I ON     
VCR          CLOCK    CHANNELAUTO  CLOCK  SET 
MANUALTIME   ZONE  ADJUST   :  0 
SELE
CT   :            SET : 
EXIT        : ACT I ON     
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :4
VCR         CLOCK     CHANNELIF   YOU   PRESS  ACTION  
KEY,   VCR  ’ S   OUTPUT CH 
SWITCHES   TO   CH  4.
VCR         CLOCK     CHANNELPLEASE   TUNE  YOUR  TV  TO    
CH  4.        
CHANNEL  08  ADDED
CHANNEL  08  DELE TED
VCR          CLOCK    CHANNELAUTO  CLOCK  SET 
MANUALTIME   ZONE  ADJUST   :  0 
SELECT   :               
EXIT        : ACT I ON     
Before Requesting Service
* Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
- 11 -
Tape Position Display Feature
Special VCR  Features Special VCR Features  Copy Your Tapes (Dubbing)  Before Requesting Service
“DETECTING TAPE
POSITION ” only
appears the first time 
a cassette is inserted
and it takes several
seconds for correct 
indication to appear.
 The present tape 
position indication is 
displayed.
BEG I N                END
To find out the present tape position. 
Tape position is displayed for VHS-C 
Cassettes type, tapes under 30 minutes, and
some other tapes, but the position is not
correct. When set to 
“ON, ” picture is displayed
regardless of signal strength.
ON: Picture is displayed despite signal
condition an may have poor quality.
OFF: Screen turns solid blue when signal is weak or non-existent.
 Selecting ON has no effect on connected 
equipment with blue back feature. Press 
  to select
and display CHANNEL. 
Press 
 to select
WEAK SIGNAL 
DISPLAY, and  press
 to set ON or OFF.
SELECT   :               
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
VCR         CLOCK     CHANNEL
The power shuts off at a preset time.
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
Press  to select
AUTO SHUT-OFF. 
Press 
 repeatedly to
change shutoff time as 
shown below.
1Press TAPE  POSITION 
to detect tape position.
DETECTING   TAPE   POSITION
2Press TAPE  POSITION 
to return to normal screen.
If Multi-brand feature is used (page 2), and this 
feature is set to on, a warning appears 
whenever an invalid key is pressed in TV mode.
If  “OFF, ” remote
warning will not appear 
if invalid key is pressed.
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR ’ S  OUTPUT CH    :3
Press  to select
REMOTE WARNING 
and  press  
 to set ON
or OFF.
Remote Warning ON/OFF Feature
1Press ACTION  to display menu.
2
3
Press ACTION  to return to normal screen.
When set to ON, all operations except for timer 
record and tape eject are prohibited. Useful for
households with small children.
VCR  LOCK  ACT I VATED
VCR  LOCK  OFF
VCR Lock cancels in 24 hours if clock is set. To turn on, 
hold down
REC on the VCR in Stop 
mode with no tape
inserted for 7 sec.
(Please ignore the NO 
CASSETTE warning.) 
To turn off,  repeat above.
Auto Shut-Off Feature
1Press ACTION  to display menu.
2
3
Press ACTION  to return to normal screen.
Weak Signal Display ON/OFF Feature
1Press ACTION to display menu.
2
3
Press ACTION  to return to normal screen.
VCR Lock Feature
* Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
- 10 -
REC    OFF 
 2 Hours
 4 Hours
 6 Hours
The shut-off countdown will not 
function during Play or Record.Note
VCR         CLOCK     CHANNELANTENNA  :   CABLE 
AUTO  SETWEAK  SIGNAL   DISPLAY : OFF
SELE
CT   :            SET : 
EXIT        : ACT I ON     
Insert pre-recorded tape. Insert blank tape with record tab.
Press REC , then PAUSE/SLOW
immediately to enter REC/PAUSE mode.
Press INPUT*  to set VCR Input mode to LINE1
for Video Input (Rear) or to LINE2 for Video 
Input (Front).  (See  “Selecting the Input Mode ”
below.)
Press PLAY  to start dubbing.
Playing VCR starts playback. Press PAUSE/SLOW
 to start dubbing.
Recording VCR starts recording. 
Press STOP  to stop dubbing.
To Monitor Dubbing on Your TV
1Turn your TV on and tune to the 
Recording VCR channel (CH3 or CH4).
2Set the VCR/ TV Selector on the
Recording VCR to  “VCR. ”
 Dubbing tapes protected with Copy 
Guard will have poor quality results.
 Selecting the Input Mode
Method 1: 
Press INPUT  repeatedly.
Channel Number  ↔↔
↔↔
↔  LINE1 
↔↔
↔↔
↔  LINE2
Method 2:
Press CH  
 / .
Display will change as below. 
“ L1” or  “L2 ” lights on Multi-Function Display
(about 4 sec.) when LINE1 or LINE2 is 
selected.
 LINE1:  For rear audio/video connection. 
LINE2:  For front audio/video connection.
Press STOP
 to stop dubbing.
Press PLAY
, then PAUSE/SLOW
immediately to enter PLAY/PAUSE mode.
1
2
Front of VCR
Connect VIDEO OUT jack on Playing VCR to VIDEO IN jack on Recording VCR.\
 
To monitor the dubbing, also connect a TV as shown.
Connect AUDIO OUT jack on Playing VCR to AUDIO IN jack on Recording VCR.\
In place of a Playing VCR, you can use other equipment, such as a Camcor\
der.
Simply connect the unit ’s Audio/Video outputs to the Recording VCR.
The operation of steps 4 and 5 must be done on both playing 
and recording VCRs at the same time.
Connection
(Front Audio/Video IN jacks are also provided)
Playing (Source) VCRRecording (Editing) VCR
1 
2 
3
4 5
Caution :Unauthorized exchanging and/or copying of copyrighted recordings may be 
copyright infringement.
- 9 -
(Rear connection shown.)
Note1 2 3
125
LINE1 (CABLE)69(TV)orLINE2
OUT TO TV
VIDEO OUT
AUDIO INVIDEO IN
TV
VHF/UHF
R 
L
VCR 
(Mono)
VCR
(Mono)IN FROM ANT.
AUDIO OUT
R
Copying Your Tapes  (Dubbing)
Panasonic Consumer Electronics Company, 
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094 
Panasonic Sales Company (“PSC”), 
Division of Matsushita Electric of Puerto Rico, Inc. 
Ave. 65 de Infanter
ía. Km. 9.5 San Gabriel Industrial Park,
Carolina, Puerto Rico 00985 Printed in Indonesia
LSQT0533BS1101-1052
P
- 8 -
Power
No power …
Recording & Playback
TV program cannot be recorded... 
Timer recording cannot be 
performed …
There is no playback picture, or the
playback picture is noisy or contains
streaks... 
Special effects playback, picture 
may contain some vertical jitter
when using a TV with an Automatic
Vertical Hold Control... 
VCR cannot be controlled...
Check the following points once again if you are having trouble with you\
r VCR.(BO : refers to  “Basic Operations ” Instruction book.)
(AO : refers to  “Advanced Operations ” Instruction book.)
Correction
 Completely insert Power Plug into an AC outlet.
 Set POWER button to on.
 Make sure power source is active.
Miscellaneous
Programs cannot be viewed on TV... 
Video cassette cannot be inserted... 
Video cassette cannot be removed... 
Video cassette ejects when a 
recording is started or the power is
turned off for timer recording... 
In Stop mode, the motor 
(CYLINDER) continues to rotate...
Remote Control
VCR cannot be remote controlled... 
ACTION and PROG buttons do not 
respond...
Correction
Check connections between VCR, external antenna, 
and TV.
 Check connections selection. (BO p. 4, AO p. 3)
 Make sure your antenna system (CABLE or TV) is
correctly set. (Channels [AO p. 12])
 Make sure cassette record tab is intact. (BO p. 3)
 Confirm that clock is set to current time and date.
 Make sure Cable/DSS box (if used) is left on and tuned
to channel to be recorded.
 Set recording start/stop times correctly. (BO p. 6)
 Make sure VCR POWER button is pressed off. (BO p. 6)
 Timer recording may not be performed or continued if a
power interruption occurs before or during a Timer
Recording, even after power is restored.
 Select channel 3 or 4 on TV to match VCR output
channel (3 or 4) (BO p. 4) or select LINE.
 Set VCR/TV selector to  “VCR. ”
 Adjust TRACKING control in either direction. (BO p. 3)
 Try Head Cleaning. (BO p. 3)
 Set TV ’s Vertical Hold Control to MANUAL, then adjust.
 Make sure VCR power is on.
 Check Remote batteries.
 Make sure VCR LOCK is set to off. (AO p. 10)
 Make sure Timer Record is not in progress.
Correction
Make sure VCR power is on.
 Make sure Remote is in VCR mode.
 Aim Remote Control directly at remote sensor on VCR. 
(BO p. 7)
 Avoid any object blocking signal path.
 Check Remote batteries. (BO p. 3)
 Make sure VCR LOCK is set to off. (AO p. 10)
 Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
 Check connections between VCR, external antenna,
and TV.
 Press VCR button for VCR mode. (AO p. 2)
 Check Remote batteries. (BO p. 3)
Correction
Make sure TV power is on.
 Make sure TV is set to output of VCR.
 Check connections between VCR, external antenna,
and TV.
 Set VCR/TV selector to  “TV. ” (BO p. 5)
 Make sure proper signal source is selected.
 Insert the cassette with window side up; record tab
facing you.
 Check if a tape is already in the unit.
 Completely insert Power Plug into an AC outlet.
 Make sure cassette record tab is intact. (BO p. 3)
 To enable Quick play mechanism, the cylinder will rotate
for about 3 minutes. This reduces response time from
Stop to Play mode and from Play to Rewind Search
mode.
If you cannot resolve the problem, please call the Customer Call Center \
for product 
assistance at 1-800-211-PANA (7262).
To locate an authorized servicenter, please call toll free 1-800-211-PAN\
A (7262).
or send e-mail to : [email protected]
 VIDEO IN 2 AUDIO IN 2
PV402 Advanced-1 (02-5-7) 2nd.p65
2002/05/08, 13:51
1
LSQT053 3B(Advanced Operations) - Front 
						

							• Tape OperationTape Operation
VCR fast forwards (skips) over 1~3 minutes 
of recorded tape. Press CM/ZERO repeatedly to changeskip time as shown below.
 No indication appears.
    PLAY 
1st  Press
2nd Press
3rd  Press 1 min Skip
2 min Skip
3 min Skip
Set to playback a recording over and over.
ON : Play repeats attape end or if 
unrecorded portion 
over 30 sec. is
detected.
VCR         CLOCK     CHANNEL
SELECT   :            SET : 
EXIT        : ACT I ON     
REPEAT  PLAY             :OFF 
REMOTE WARNING     :ON
AUTO  SHUT- OFF       :OFFIDIOMA/LANGUE : ENGLISHVCR’ S  OUTPUT CH    :3
Press to select REPEAT PLAY 
and  press  to set ON
or OFF.
To quickly return to a specified tape location.
Unit will go into FF or 
REW mode and stop at
the last point the
Counter was set to
0:00:00.
Press RESET
COUNTER at desired
position 
to reset to
“ 0:00:00 ”.
Press CM/ZERO in Stop
mode  to start ZERO
SEARCH.
Repeat Play
1Press ACTION  to display menu.
2
3
Press ACTION  to return to normal screen.
Zero Search
1Press DISPLAY during play 
to display Counter.
2
3
Continue to record, playback, etc .
4Press STOP.
5
Commercial Skip
1Press CM/ZERO  in Play mode.
- 7 -
*
Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
PLAY       1 2 : 0 0AM 0 : 0 0 : 0 0 SP
REW        1 2 : 3 0AM          CH  02 0 : 30 : 30 SP
STOP       1 2 : 3 1AM          CH  02 0 : 0 0 : 0 0 SP
Tape Operation
 To Calculate Index Number
Example 1:
To go to rec. 2 from rec. 4, enter 3 and press 
REW.
Example 2:To go to rec. 6 from rec. 2, enter 4 and press 
FF. 
NOTE: 
 indicates start points of each recording.
 If Index Search is started very close to an 
index mark, that index mark may not be
counted in the search.
Search System
For each recording, an invisible index mark is placed on the tape. A pro\
gram index and 
information are also included for timer recordings. These marks are used\
 to access or 
scan recordings.
Fig. 1
Fig. 2
Fig. 3
Locates end point of recording for continuity.
Examples of  Program End Search .
If search 
exceeds a few 
seconds in 
BLANK area.
➛ search continues 7 sec. past end point,
➛  tape rewinds to 10 sec. before end point,
➛  tape plays to end point and stops.
Upon locating end point, 

If Program End Search is started very 
close to an index mark, that mark may be 
skipped over.
 To cancel, press PLAY or STOP.
End Point
Press SEARCH
* to
display SEARCH in Stop 
or Play mode, and then
press NUMBER keys  to
select recording 
number. 
 To calculate number, 
see below.
Press FF or REW  on
the remote to start
search. Press FF 
on the remote
to start PROGRAM
END SEARCH.
Play begins at search
end. To search forward
or back 1 index,  press
FF or REW  on the
remote or VCR while
screen left is displayed
(10 sec.).
6157234
17534 62
Program  2
Program 1 
the current tape position  
Press SEARCH button
BLANKINDEX
FF
Index SearchProgram End Search
1
2 1
Press SEARCH twice
 to display SEARCH
in Stop or Play mode.
2
End Point
Program 2 or BLANK
Program 1 
the current tape position  
Press SEARCH button
FF
INDEX
End Point
Program  2
Program 1 the current tape position  
Press SEARCH button
INDEXINDEX BLANK BLANK
FF
- 6 -
Note
Notes

To cancel,  press
STOP  or PLAY . 
To cancel,  press
STOP  or PLAY .
                   SEARCH 
      INDEX          PROGRAM END
ENTER   INDEX  NUMBER  :1
USING   1- 9 KEYS 
FORWARD  SEARCH  :FF
REVERSE  SEARCH  :REW
NEXT     :SEARCHEXIT     :STOP
           INDEX  SEARCH 
FORWARD  SEARCH  :FF
REVERSE  SEARCH  :REW
                   SEARCH 
      INDEX          PROGRAM END
SEARCH START  :FF 
EXIT     :SEARCH
 On-Screen Displays (OSD)  Warning and Instruction DisplaysWarning and Instruction Displays
- 5 -
*
Important: If a remote control button does not work when pressed, 
press the VCR button on the remote and try the button again.
On-Screen Displays (OSD)
- 4 -
Advanced Connections Advanced Connections  Multi-Brand Control Feature
You CannotYou Can
record and view 
both scrambled
and 
unscrambled 
channels if
additional
equipment is
added. 
This connection 
requires: two
converter
boxes, an A/B 
switch, and a 2- 
way splitter. 
view channel
other than
the one
selected for 
any type of 
recording.
 do a Timer 
recording of 
a channel
unless you
select it at
the cable 
box.
If your TV has AUDIO IN and VIDEO IN terminals, you can connect your VCR\
 
to them to receive higher quality picture and sound.
IN
VIDEO
AUDIO
R
L OUT
IN FROM ANT.
OUT TO TV
 
AUDIO
IN 1
VHF/UHF
 R
 L
  VIDEO
OUTTV
IN 2IN 1
CABLE BOX
OUT
INOUT 2
OUT 1
2-Way Splitter
CABLE BOX
OUT
A/B Switch
VCR
IN
VHF/UHF


  
  
   Connect With Two Cable Boxes
VCR
IN FROM ANT.
OUT TO TV
 
AUDIO
IN 1
VHF/UHF
 R
 L
  VIDEO
OUT
CABLE BOX
OUT
IN
IN
R
L OUT
TV
VIDEO
AUDIO
VHF/UHF
  
  
   With a Cable Box (VCR 
  
  
    Cable Box)
ANT
or
CATV
You CannotYou Can
 record 
scrambled 
channels.

view any
(including
scrambled)
channel.
 use VCR
Remote
Control to 
select 
channels
without using
Multi-brand
control feature.
ANT
or
CATV
Audio/Video connection
TV
VCR
IN FROM ANT.
OUT TO TVVHF/UHF
VIDEO IN
R
VIDEO  OUT
AUDIO IN
AUDIO OUT
- 3 -
Multi-Brand Control Feature
The Remote Control can be set to control some TV functions.
ModeUnitVCR TV
VCR
TV All
VOL UP/DOWN
POWER, INPUT, ENTER, 
NUMBER keys, CH UP/DOWN, 
VOL UP/DOWN
VCR/TV, PLAY, STOP, EJECT, SAP/Hi-Fi, DISPLAY, 
FF, REW, PAUSE/SLOW, REC, 
SPEED, CM/ZERO,
RESET COUNTER,  TAPE POSITION
After remote is set up, you can select VCR or TV for the desired functio\
n. 
Press VCR 
or TV  on the remote.
(Table below shows available unit buttons for each mode.)
 Not all functions listed may be controllable.
 In TV mode, it may be necessary to press ENTER after pressing NUMBER key\
s for channel 
selection.➛ 
hold down  TV button,
➛  enter code with  NUMBER keys.
 Repeat setup after remote battery replacement.
 Remote will not control every TV made by the manufacturer listed. If you\
 get no
response, your particular unit cannot be controlled. There are NO additi\
onal codes for
the products listed. If your product is not listed, then the remote is n\
ot compatible with 
that product.
Multi-Brand Control Setup
1Find your TV Brand Code Number from those shown below.
2Setup for TV control,
3Confirm code entry,
➛  press POWER  to turn your TV on or off.
  See table below for controllable functions in each mode.
Using Multi-Brand Control
Panasonic ....................... 01, 02 
Quasar ............................ 01, 02
RCA ...................................... 03
GE ......................................... 03
Zenith .................................... 04
Magnavox .............................. 05
TV Brand Code Numbers
Sylvania ................................. 05 
Sharp ............................... 06, 07
Sony ...................................... 08
Toshiba ................................. 09
Sanyo .................................... 10
Fisher .................................... 10 JVC ....................................... 11
Hitachi ................................... 12
Mitsubishi ........................ 07, 13
Samsung ............................... 14
Gold Star ................... 15, 16, 17

Due to changes in infra-red commands used by manufacturers, some brands \
have several codes. 
If your unit does not respond to the first code, please try the next one\
.
 Some TV brands require you to turn on the power manually.
- 2 -
Notes
Notes
Important Notes
CH 0 8When a function button is 
pressed, e.g. PLAY, or you 
change channels, a 5 second 
display appears. These displays will alert you to a missed operation or provide further i\
nstructions.OSD
Caution
Page
PLEASE SET CLOCK BY 
PRESSING ACTION KEYIf you attempt to set or review a Timer 
Recording and the Clock is not set...
After a Timer Program has been set...
If you press REC on the remote 
control or VCR, and a cassette is
inserted with no record tab...
If you press PLAY, FF, REW, or REC
on the remote control or VCR without
a cassette inserted...
CHECK CASSETTE 
RECORD TAB 
NO CASSETTE 
TURN VCR OFF 
FOR TIMER RECORDING
If you press POWER or STOP during 
a Timer Recording... 
(visible in VCR mode only)
If you press an invalid key on the 
remote while in TV mode...TO CANCEL TIMER REC 
PRESS POWER THEN
STOP KEY 
VIDEO HEADS MAY 
NEED CLEANING
PLEASE INSERT HEAD 
CLEANING CASSETTE 
OR REFER TO MANUAL 
END       :PLAY 
VCR LOCK ACTIVATED REMOTE CONTROL IS SET 
TO TV MODE 
USE VCR : VCR KEY
If head cleaning becomes necessary
while playing back a tape...
If you press a function button other
than STOP/EJECT or POWER while 
the VCR is in VCR Lock mode...
See page 6 of 
Basic Operations 
book 
See page 6 of 
Basic Operations 
book 
See page 3 of 
Basic Operations
book 
See page 5 of 
Basic Operations
book 
See page 6 of 
Basic Operations
book 
See page 3 of 
Basic Operations 
book
See page 10
See pages 2, 10
Function & Channel Displays
When blank tape is detected during play, or the 
current channel has no signal (with Weak Signal 
Display feature (p. 10) set to OFF), the TV screen 
will turn solid blue.
Blank Tape/No Video Signal Indications
To display or remove overlay at right, 
➛  press DISPLAY* .
VCR Status & Clock Displays
REC         1 2 : 0 0AM0 : 25CH 02-0 : 1 2 : 3 4 SP
Function Status
Rec Time Remaining
(OTR mode only. See p. 5
of Basic Operations book.)
Current Time
Channel
Tape Speed 
(See p. 3 of Basic 
Operations book.)
Counter
Connect the VCR
’s VIDEO OUT jack to the TV ’s VIDEO IN jack.1
2Connect VCR ’s AUDIO OUT jack to the TV ’s AUDIO IN jack.
Set the VIDEO/TV selector of your TV (Monitor/Receiver) to  “VIDEO. ”3
PV402 Advanced-2 (02-5-7) 2nd.p65 2002/05/08, 13:52
3
LSQT053 3B(Advanced Operations) -  Back