Panasonic Ventilating Fan Fv 05vs1 Installation Instructions

READ AND SAVE THESE INSTRUCTIOINS.
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
Applicable to Models: FV-05VS1, FV-08VS1
SUPPLEMENTARY
INSTALLATION INSTRUCTIONS
(For Contractor Pack)
Housing Can
FV-05-08VSA1
Motor/Grille Assembly
FV-05VSB1, FV-08VSB1
Table of Contents
2Unpacking
2General Safety...

GENE AL SAFETY INFO MATIONRRGENE AL SAFETY INFO MATIONRR
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make sure that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation
Safety and Health Act (OSHA).
4. Always disconnect the power source before working on or near the fan, motor or junction box.
5. Protect the power cord from sharp edges, oil,...

SUPPLIED ACCESSORIES SETS(4 )SUPPLIED ACCESSORIES SETS(4 )
(A) For Motor / Grille Assembly of model: FV-05/08VSB1
Quantity Appearance
Part name
Grille4
(B) For Housing Can of model: FV-05-08VSA1
WIRING DIAGRAM
4 24
4
4
8
4
8
4
Thumb screwLong screw
(ST4.2X20)
Suspension
bracketI
Suspension
bracketII
Screw
(ST4.2X8)I
Suspension
bracketIII
Screw
(ST4.2X10)II
Quantity Appearance
Part name
3
Spacer
Fan body
Red
Capacitor
White
BlackJunction box
Black LivePower supply
AC120V 60Hz
White Neutral White...

4
INSTALLATION JOIST MOUNTING-II()INSTALLATION JOIST MOUNTING-II()
2 Screw (ST4.2X8)I
Suspension bracketIIISuspension bracketII
2. Insert the supension bracket into the fan body and
adaptor. (Select the suspension bracket as shown below)
Spacing a on center joists
Insert suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24 inchesRefer to Fig. 2-1
Refer to Fig. 2-2
Refer to Fig. 2-3
Refer to Fig. 2-4
If spacing A on center joists is 24 inches, connect
suspension bracket and (C4 mark to C4...

2 Long screws
(ST4.2X20)
screw (ST4.2X10)II
Fan bodyJoist
2 Long screws
(ST4.2X20)
Joist
4 Long screws (ST4.2X20)
Fan body
INSTALLATION JOIST MOUNTING-II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II( ) CONTINUED
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig. 5)
6. Refer to wiring diagram (page 3).
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green to green;
Replace the junction box cover. (Fig....

CAUTION:
Joists Adaptor
2 Long screws
(ST4.2X20)
inches mm()Fig. 7
INSTALLATION JOIST MOUNTING-II( ) CONTINUEDINSTALLATION JOIST MOUNTING-II( ) CONTINUED
8. Finish ceiling work. Ceiling hole should be aligned
with the edge of the flange. (Fig. 6)
6
INSTALLATION JOIST MOUNTING-II II()INSTALLATION JOIST MOUNTING-II II()
1. Disconnect plug connector from receptacle and
remove adaptor from fan body before starting
installation.
2. Insert the suspension bracket into the adaptor and
secure it to joists by...

Fig. 8
Fig. 9
2 Long screws
(ST4.2X20)Screw (ST4.2X10)II
Conduit
Junction box cover
Circular duct
Joist
Fan body
Adaptor
claws
INSTALLATION JOIST MOUNTING- CONTINUEDII II()INSTALLATION JOIST MOUNTING- CONTINUEDII II()
7
Make sure that adaptor claws are properly inserted
into body slots.IMPORTANT:
5. Insert the fan body into joists. (Fig. 8)
6. Secure the fan body to adaptor by using thumb
screw.
7. Secure to joists by using
long screws (ST4.2X20) and secure it to fan body
by using screw (ST4.2X10) in...

8
INSTALLATION JOIST MOUNTINGIII I-()INSTALLATION JOIST MOUNTINGIII I-()
C1
C2
C3
C44 kinds of -joist
inches (mm)I
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Suspension bracket
The suspension can comply with
different kinds of -joist.III
III
I bracket
1. Before installation, Secure the fan body to adaptor by
using thumb screw. (Fig. 1 of page 4)
2. Connect the suspension to fan body. (Fig. 10)
(Select the hole by checking joist size fix the screw
to the frame hole.)bracketIII
I-
3. Connect the...

3. Insert the fan body between joists.
Make sure the fan body is level and square
(perpendicular) with the joists. (Fig. 13)
INSTALLATION BETWEEN JOIST MOUNTINGIV( ) CONTINUEDINSTALLATION BETWEEN JOIST MOUNTINGIV( ) CONTINUED
4. Secure the suspension bracket to joists by using long
screws (ST4.2X20). (Fig. 14, Fig. 15)
inches mm()
9
5. Secure the suspension bracket to fan body by using
screw (ST4.2X10). (Fig. 15)II
6. Follow step 5 to 9 of installation (page 5~page 6)
to complete the installation work.I...

Fig. 19
IMPORTANT:
INSTALLATION WALL INSTALLATION-VII I()INSTALLATION WALL INSTALLATION-VII I()
1. Remove adaptor from fan body before starting installation.
(Fig. 19)
2. Insert the suspension bracket into the adaptor. (refer to
step 2 of installation of page 6).II
UP
When the product is installed on the wall, the adaptor shall be faced upward. (Fig. 18)
Prohibition
10
(2) Inspect duct work and wiring before proceeding with installation.
(3) Plan suitable location for ventilating fan. (next to ceiling...