Panasonic Ventilating Fan Fv 05vfl2 Installation Instructions

Ventilating Fan
READ AND SAVE THESE INSTRUCTIONS.R
Please
readthese
instructionscarefullybeforeattempting
toinstall,
operate or service the Panasonic Ventilating Fan. Failure to comply
with instructions could result in personal injury and/or property
damage. Please retain this booklet for future reference.
SpecificationsDimensions
Description
12 11-12
13-14
14 6-84
4-54 32
2
Table of Contents
Supplied Accessories
Unpacking
General Safety Information
I
Installation( Wooden Header )
10III( -Joist Mounting...

FV-05VFL2
FV-08VFL2
FV-11VFL2
Quantity Appearance
Part name
Screw
M4X8I21
Grille
Suspension
bracketI
Suspension
bracketII
1
1
2Screw
M4X12II
Screw
M4X16III
2
Machine screw
M4X81
Quantity Appearance
Part name
2
1
1
18W
Fluorescent
lamp
4W
Incandescent
lamp
Light unit
These Panasonic ceiling mount ventilating fan models use a sirocco fan with dolphin-shaped blades driven by
a capacitor motor.
The motor is designed to have an extended service life with reduced energy consumption.
It also incorporates a...

(For 16 inches on center joists,only use suspension bracket , for 19.2 inches on center joists, only use
suspension bracket , If more than 19.2 inches on center,use suspension bracket & .)I
III II III
Junction box cover
Junction box
Lighting unit assy
Fluorescent lamp
Night lamp
Adaptor connector
Part name No. Part nameNo.
1
2
3
4
5
67
8
9
10
11
12
Damper BodyAdaptor
Grille
Suspension bracket
Bracket cover
Unit: ( )inches mm
79
1110
10 1/4 259()
11 7/8 (301)
8
43/8 110()
5 1/2 (141) 13/4 45() 126()...

Specifications are based on HVI standard.
Unpack and carefully remove unit from carton.
Refer to the Supplied Accessories list to verify that all parts are present.
1. Do not install this ventilating fan where air temperature may exceed 40 C (104 F).oo
2. Make certain that the electric service supply voltage is 120V, 60 Hz.
3. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and
the Occupation Safety and Health Act (OSHA).
4. Always disconnect the power source...

CAUTION:
1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
2. Not for use in cooking area. (Fig .B)
3. This product must be properly grounded.
Floor
Do not install above or(Cooking area)
inside this area
45o45o
equipmentCooking
Fig. B
WARNING:
To reduce the risk of fire, electric shock or injury to persons, observe the following;
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact
the manufacturer.
B....

6
Fig.1
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketISuspension
bracketIII
Fig.2-1
Fig.2-2
Fig.2-3
Fig.2-4
Fan body
Fan body
Fan body
Suspension
bracketI
Suspension
bracketIII
Suspension
bracketII
Fan body
Thumb screw
Screw (M4X8)I
Suspension bracketIIISuspension bracketII
2. Insert the supension bracket into the fan body and
adaptor. (select the suspension bracket as show below)
Spacing A on center Joists
Insert Suspension bracket
12 inches
16 inches
19.2 inches vertical joists
24...

Fig.3-2
Fig.4
4. Install the suspension bracket to joists by using long
screws (M4X30) and secure it to the fan body by
using screw (M4X12) (Fig.4)II
Fan body Joist
4-Long screws(M4X30)
Joist Fan body
2-Long screws
(M4X30)
2-Long screws
(M4X30)
screw (M4X12)II
7
5. Remove junction box cover and secure conduit or
stress relief to junction box knock-out hole. (Fig.5)
6. Refer to wiring diagram below.
Using wire nuts, connect house power wires to
ventilating fan wires:
black to black; white to white; green...

3. Follow steps 5 to 7 of the installation (page 7) to
complete the duct work and wiring.I
8
9. Insert the plug connector and plug connector
into the receptacle and receptacle respectively,
and secure the light unit to the fan unit with 2 screw
(M4X16) and 1 machine screw (M4X8). (Fig.6)II III
II III
III
10. Insert the fluorescent lamps and screw the night
lamp into the light unit.(Fig.6)
11. Insert mouting springs into slots as shown
and mount grille to fan body.(Fig.7)
Slot
Grille Mounting spring...

Make sure that adaptor claws are properly inserted
into body slots.
IMPORTANT:
5. Insert the fan body into joists. (Fig.9)
6. Secure the fan body to adaptor by using thumb
screw and plug connector to receptacle(Fig.10)
Fig. 9
When mounting
body and blower
separately
1. Loosen 4 screws (but
do not remove them
from blower). (Fig.12-1)
2. Remove blower section.
(Fig.12-2)
4. Insert fan body (without
blower section) into joists
(Fig.9)
5. Secure the adaptor to
fan body by using thumb
screw. (Fig.10)
7....

1. Before installation, secure the to by
using thumb screw (Fig.13) Secure the lighting unit to
fan body (refering to Fig.6 of page 8).fan body adaptor
.
10
Fig.13
Suspension bracket
The suspension can comply with
different kinds of joists.III
III
I- bracket
C
2. Connect the suspension to fan body. (Fig.14)
(Select the hole by checking -joist size and fix the
screw to the frame hole.)bracketIII
I
C1
C2
C3
C44 kinds of joist
inches (mm)I-
9/16 ( )14.3
11/16 (17.5)
31/32 (24.6)
1 17/32 38.9()
Thumb screw...