Panasonic Vdr D220 Operating Instructions Manual

							71LSQT1146
Editing
Editing still pictures
(SD)
The deleted files cannot be restored.
¬Rotate the mode dial to select  .
1Press the   button during 
playback.
2When the confirmation message 
appears, select [YES], then press 
the joystick.
¬Rotate the mode dial to select  .
1Press the   button in the 
thumbnail display. 
2Select [SELECT] or [ALL] and 
press the joystick.
≥When [ALL] is selected, all files on the SD card 
except the locked files will be erased. Proceed 
to step 5.
3(Only when [SELECT] is selected in step 2)
Select the file to be deleted, then 
press the joystick.
The selected file is encircled by a red frame.
≥When the joystick is pressed again, the 
selected file will be canceled.
≥Up to 8 files displayed on a page can be set in 
succession.
4(Only when [SELECT] is selected in step 2)
Press the   button.
5When the confirmation message 
appears, select [YES], then press 
the joystick.
(Only when [SELECT] is selected in step 2)
To continue deleting other files
Repeat steps 3-5.
To complete editing
Press the MENU button.
∫Deleting still picture files recorded on an 
SD card by other products
A still picture file (other than JPEG) that cannot 
be played back on this unit may be erased.
≥You can also delete files by pressing the 
MENU button, selecting [PICT. SETUP] # 
[DELETE] and then selecting [SELECT] or 
[ALL].
≥In case of [ALL], the deletion may take time if 
there are many files on the SD card.
≥Do not turn off this unit while deleting.
≥When you delete files, use a battery with 
sufficient battery power or use the AC adaptor.
≥Do not remove the SD card while deleting.
Deleting still pictures
This is for deleting still picture files 
recorded on SD cards.
Deleting files one at a time
Deleting multiple files from the 
thumbnail display
LSQT1146.book  71 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							72LSQT1146
Editing
≥If files conforming to DCF standard are 
deleted, all the data related to the files will be 
deleted.
(SD)
Still picture files recorded on an SD card can be 
locked so that they are not deleted by mistake. 
(However even if you lock some files on an SD 
card, formatting the card will delete all the files.)
¬Rotate the mode dial to select  .
1Press the MENU button, then 
select [PICT. SETUP] # [LOCK] 
# [YES] and press the joystick.
2Select the file to be protected, 
then press the joystick.
[ ] display appears and the selected file is 
locked.
≥Press the joystick again to release the lock 
setting.
≥You can also select multiple files in succession.
To complete the settings
Press the MENU button.(SD)
You can write the data of the still pictures to be 
printed and the number of prints (DPOF data) 
onto the SD card.
¬Rotate the mode dial to select  .
1Press the MENU button, then 
select [PICT. SETUP] # 
[DPOF SET] # [SET] and press 
the joystick.
2Select the file to be set, then 
press the joystick.
The number of prints set to be in DPOF is 
displayed.
3Move the joystick up or down to 
select the number of prints, then 
press the joystick.
≥You can select from 0 to 999. (The selected 
number of pictures can be printed with the 
printer supporting DPOF.)
≥To cancel the setting, set the number of prints 
to [0].
≥You can also select multiple files in succession.
To complete the settings
Press the MENU button.
Locking still pictures
This is for preventing still picture files 
from being deleted by mistake.
MENU
DPOF setting
This is for writing the printing data on 
an SD card.
MENU
LSQT1146.book  72 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							73LSQT1146
Editing
To cancel all DPOF settings
Press the MENU button, then select 
[PICT. SETUP] # [DPOF SET] # 
[CANCEL ALL] and press the joystick.
≥When the confirmation message appears, 
select [YES], then press the joystick.
∫What is DPOF?
DPOF stands for Digital Print Order Format. This 
enables picture printing information to be written 
onto an SD card so that it can be used on a 
system supporting DPOF.
≥The DPOF setting can be established for up to 
999 files.
≥DPOF setting made on other devices may not 
be recognized by this unit. Please perform the 
DPOF settings on this unit.
≥You cannot add the recording date to pictures 
to be printed with the DPOF settings.
LSQT1146.book  73 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							74LSQT1146
Disc and card management
Disc  an d c ard ma nage ment
Disc management
(-RW‹VR›) (-RW‹V›) (-R)
If you insert a DVD-RW or a DVD-R disc 
recorded in this unit (that has not been 
finalized) into another device such as DVD 
recorder, computer, etc., the disc may 
become unusable.
Be sure to finalize the disc on this unit before 
inserting it in other devices.
¬Rotate the mode dial to select  .
1Connect this unit to the AC 
adaptor.
≥Finalization cannot be executed when using a 
battery. If the power supply stops while 
finalizing, the finalization will fail and the data 
may be damaged. Use the AC adaptor.
2Press the MENU button, then 
select [DISC SETUP] # [FINALIZE] # [YES] and press 
the joystick.
3When the confirmation message 
appears, select [YES], then press 
the joystick.
When finalizing a DVD-RW (Video format) or 
DVD-R, a top menu containing thumbnails is 
created.
≥When finalizing is complete, press the MENU 
button to exit the message screen.
≥Do not finalize a disc recorded on this unit 
using any other device.
≥In the case of a double sided disc, finalize each 
side.
≥The top menu created when finalizing does not 
appear on this unit. Play back the disc on a 
DVD player.
Titles are displayed by recording date on the 
top menu. However, when [PLAY MODE] is set 
to [BY DATE] to view scenes by recording 
date, some scenes recorded on the same date 
may be separated. (l61) These scenes will 
be displayed as separate titles on the top 
menu.
≥It may take time to finalize a disc.
≥If this unit becomes hot or is shaken strongly or 
impacted while finalizing, the finalization will 
fail and the disc may become unplayable on 
other devices.
≥If the power supply stops while finalizing, the 
finalization will fail and the disc may become 
unplayable on other devices even if disc repair 
is carried out.
Finalizing a disc
It allows the discs to be played on 
other devices.
DVD-RAM:
≥It is not necessary to finalize DVD-RAM.
DVD-RW (VR format):
≥DVD-RW (VR format) after finalization can 
be recorded and edited in the same way as 
DVD-RW (VR format) before finalization.
≥After finalizing a DVD-RW (VR format) once, 
you cannot finalize it again. (Even if you 
record on or edit a DVD-RW (VR format) 
after finalizing, it is not necessary to finalize 
it again.)
DVD-RW (Video format), DVD-R:
≥After finalizing, the disc becomes play-only 
and you can no longer record.
≥When you un-finalize a DVD-RW (Video 
format), the disc can be used for recording 
again. (l75)
MENU
LSQT1146.book  74 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							75LSQT1146
Disc and card management
(-RW‹V›)
¬Rotate the mode dial to select  .
1Press the MENU button, then 
select [DISC SETUP] # 
[UN-FINALIZE] # [YES] and 
press the joystick.
2When the confirmation message 
appears, select [YES], then press 
the joystick.
≥When un-finalizing is complete, press the 
MENU button to exit the message screen.
≥DVD-RW (VR format) cannot be un-finalized. 
DVD-RW (VR format) after finalization can be 
recorded and edited in the same way as DVD-
RW (VR format) before finalization.
≥DVD-R cannot be un-finalized.
≥When you un-finalize the disc, use a battery 
with sufficient battery power or the AC adaptor.
(RAM) (-RW‹VR›)
This is for preventing recorded contents from 
being deleted or edited by mistake.
Further recording and editing is not possible on 
protected discs until the protection is released.
¬Rotate the mode dial to select  .
1Press the MENU button, then 
select [DISC SETUP] # [DISC PROTECT] and press the 
joystick.
2When the confirmation message 
appears, select [YES], then press 
the joystick.
To release disc protection
1) Press the MENU button, then select 
[DISC SETUP] # [DISC PROTECT] and 
press the joystick.
2) When the confirmation message appears, 
select [YES], then press the joystick.
≥If the disc has been protected on another device, 
it may not be possible to release the protection on 
this unit. In this case, release the protection on the 
device that you used to protect it.
(RAM) (-RW‹VR›) (-RW‹V›)
Please be aware that if a disc is formatted, then 
all the data recorded on the disc will be erased.
¬Rotate the mode dial to select   or 
.
1Press the MENU button, then 
select [DISC SETUP] # 
[FORMAT DISC] # [YES] and 
press the joystick.
Un-finalizing a DVD-RW
This is for un-finalizing a DVD-RW 
(Video format) so that it can be used 
for recording.
Protecting a disc
MENU
Formatting discs
This is for initializing discs.
MENU
MENU
LSQT1146.book  75 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							76LSQT1146
Disc and card management
≥When formatting a DVD-RAM, skip to step 3.
2(When formatting a DVD-RW only)
Select format type (l21), then 
press the joystick.
3When the confirmation message 
appears, select [YES], then press 
the joystick.
≥When formatting is complete, press the MENU 
button to exit the message screen.
≥In the case of a double sided disc, format each 
side.
≥It may not be possible to format a disc with 
many scratches or dirt. Such discs cannot be 
used.
≥During formatting, do not turn this unit off.
≥When you format the disc, use a battery with 
sufficient battery power or the AC adaptor.
Formatting DVD-RAM:
≥We recommend formatting on this unit. If 
formatting on a computer, use the supplied 
software. For more details, refer to the 
operating instructions of the software.
If you connect this unit to a computer to format 
a DVD-RAM, you cannot use DVDForm (l83) 
to physically format it. Use a separate DVD-
RAM drive to physically format a DVD-RAM.
Formatting DVD-RW:
≥Format on this unit.
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
Information such as the number of recorded 
scenes, the remaining space and whether or not 
the disc is finalized or protected is displayed.
¬Rotate the mode dial to select   or 
.
Press the MENU button, then select 
[DISC SETUP] # [INFORMATION] # 
[YES] and press the joystick.
To exit the information screen
Press the MENU button.
Card management
(SD)
Please be aware that if an SD card is formatted, 
then all the data recorded on the card will be 
erased. Store important data on a computer, etc.
¬Rotate the mode dial to select   or 
.
1Press the MENU button, then 
select [SETUP] # 
[FORMAT CARD] # [YES] and 
press the joystick.
2When the confirmation message 
appears, select [YES], then press 
the joystick.
≥When formatting is complete, press the MENU 
button to exit the message screen.
Displaying disc information
Formatting an SD card
This is for initializing cards.
MENU
MENU
LSQT1146.book  76 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							77LSQT1146
Disc and card management
≥Use this unit to format SD cards. If an SD card 
is formatted on other products (such as a 
computer), the time spent for recording may 
become longer and you may not be able to use 
the SD card.
≥Depending on the type of SD card being used, 
it may take time to format.
≥During formatting, do not turn this unit off.
≥When you format the SD card, use a battery 
with sufficient battery power or the AC adaptor.
≥Do not remove the SD card while formatting.
LSQT1146.book  77 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							78LSQT1146
With other products
With other pro ducts
With a TV
(RAM) (-RW‹VR›) (-RW‹V›) (-R) (SD)
The motion pictures and still pictures recorded by 
this unit can be played back on a TV.
≥Use the AC adaptor to free you from worrying 
about the battery running down.
1Connect this unit and a TV.
AAV/S cable (supplied)
≥Insert the plugs as far as they will go.
* If the TV has an S Video terminal, also connect 
the S Video plug to it. This allows you to enjoy 
more beautiful pictures.
2Turn on this unit, then rotate the 
mode dial to select   or  .
3Change the input channel on the 
TV.
≥The channel set will differ depending on the 
terminal to which the unit is connected.
4Start playback on this unit.
The image and audio are output on the TV.
∫If the image or audio from this unit is not 
output on the TV
≥Check that the plugs are inserted as far as they 
go.
≥Check the connected terminal.
≥Check the TV’s input setting (input switch). 
(For more information, please read the 
operating instructions for the TV.) 
≥If the images are not displayed correctly on a 
wide-screen TV, adjust the aspect setting on 
the TV. (Refer to the operating instructions of 
the TV for details.) If the pictures are displayed 
squeezed horizontally on a regular TV (4:3), 
change the [TV ASPECT] setting on this unit. 
(lbelow)
∫To watch images with a 16:9 
aspect ratio on a regular TV (4:3)
When playing back motion pictures recorded with 
a 16:9 aspect ratio ([ASPECT] was set to [16:9]) 
or still pictures recorded with a 16:9 aspect ratio 
([PICTURE SIZE] was set to [ ]) on a TV with 
a 4:3 aspect ratio, the images may be squeezed 
horizontally. In this case, change the menu 
setting to play back the pictures in the original 
aspect ratio. (Depending on the TV setting, the 
pictures may not be displayed correctly. For 
more information, please read the operating 
instructions of your TV.)
Press the MENU button, then select 
[SETUP] # [TV ASPECT] # [4:3] 
and press the joystick.
Example of images with a 16:9 aspect ratio on 
a regular TV (4:3)
≥This function’s default setting is [16:9].
Playback on TV
VIDEO IN S VIDEO IN
*
AUDIO IN
A
[TV ASPECT] setting
[16:9][4:3]
0.2
LSQT1146.book  78 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							79LSQT1146
With other products
With a DVD recorder/
player
≥Do not insert a DVD-RW or a DVD-R disc 
recorded in this unit (that has not been 
finalized) into another device such as DVD 
recorder, DVD player, computer, etc. as the 
disc may become unusable.
≥If you insert a DVD-RW disc recorded in this 
unit (that has not been finalized) into 
another device such as DVD recorder, 
computer, etc., a format message may 
appear. Do not format the disc as all the 
important data recorded on the disc will be 
erased and cannot be recovered.
≥When playing back a disc on a DVD recorder/
player, place the device so that the disc lies 
flat.
(RAM) (-RW‹VR›)
1[Only when playing back a DVD-RW (VR 
format)]
Finalize the disc on this unit. 
(l74)
2Insert the disc in the playback 
device and then play it back.
≥Playback is only possible on devices that 
support 8 cm (3z) DVD-RAM or DVD-RW (VR 
format). Refer to the operating instructions of 
the playback device.
≥You cannot record images that allow “One time 
only recording” on a 8 cm (3z) disc.(-RW‹V›) (-R)
1Finalize the disc on this unit. 
(l74)
2Insert the disc in the playback 
device and then play it back.
≥Playback is possible on devices that support 
8cm (3z) DVD-Video, but playback on all DVD 
players is not guaranteed.
≥Playback of DVD-R DL is only possible on 
devices that support 8 cm (3z) DVD-R DL. 
Refer to the operating instructions of the 
playback device.
≥The recording time is not displayed.
(RAM) (-RW‹VR›) (-RW‹V›) (-R)
If you have a DVD recorder with hard disk, 
images recorded by this unit can be stored on 
the hard disk.
≥Do not insert a DVD-RW or a DVD-R disc 
recorded in this unit (that has not been 
finalized) into the DVD recorder as the disc 
may become unusable.
≥If you insert a DVD-RW disc recorded in this 
unit (that has not been finalized) into the 
DVD recorder, a format message may 
appear. Do not format the disc as all the 
important data recorded on the disc will be 
erased and cannot be recovered.
≥If you want to record (dub) a disc that the DVD 
recorder is not compatible with, connect this 
unit and the DVD recorder with the AV/S cable 
and then record (dub) the disc. 
(l80)
Playback on DVD recorder, 
DVD player, computer etc.
Playing back a DVD-RAM or a 
DVD-RW (VR format)
Playing back a DVD-RW (Video 
format) or a DVD-R
Copying (dubbing) 
recordings onto a DVD 
recorder’s hard disk
LSQT1146.book  79 ページ  ２００６年１２月５日　火曜日　午前１０時４０分 
						

							80LSQT1146
With other products
1[Only when you record (dub) a DVD-RW or a 
DVD-R]
Finalize the disc on the unit. 
(l74)
2Insert the disc in the DVD 
recorder, then copy (dub) the 
contents onto the hard disk.
≥For details on how to copy (dub) the images 
onto the hard disk, refer to the operating 
instructions of the DVD recorder.
≥If your DVD recorder has an SD card slot, you 
can write the still picture files recorded on an 
SD card with this unit to a disc or the hard disk.
≥You cannot record images that allow “One time 
only recording” on a 8 cm (3z) disc.
≥If you copy (dub) images recorded on a DVD-
RW (Video format) or a DVD-R disc, the title 
name of the images after copying (dubbing) 
becomes the date they were dubbed.
With a VCR
(RAM) (-RW‹VR›) (-RW‹V›) (-R)You can record (dub) images played back on this 
unit onto other video devices.
You can create a playlist by gathering the scenes 
you want to record (dub), then record (dub) the 
scenes in this playlist only to other devices. 
(l66)
≥Use the AC adaptor to free you from worrying 
about the battery running down.
1Connect this unit and a video 
device.
AAV/S cable (supplied)
≥Insert the plugs as far as they will go.
* If the video device has an S Video terminal, 
also connect the S Video plug into it. This 
allows you to enjoy more beautiful pictures.
2Turn on this unit, then rotate the 
mode dial to select  .
3Change the input channel on the 
video device and TV.
≥The channel set will differ depending on the 
terminal to which the unit is connected.
4Start playback on this unit.
Then start recording on the 
connected device.
≥See the operating instructions of the video 
device for details.
If you record (dub) images directly from the 
disc or with the AV/S cable and then play them 
back on a wide-screen TV, they may be 
squeezed horizontally. In this case, refer to 
the operating instructions of the device you 
are recording (dubbing) to or read the 
operating instructions of the wide-screen TV 
and set the aspect setting to 16:9 (Full).
Recording (dubbing) images 
onto other video devices
VIDEO IN S VIDEO IN
*
AUDIO IN
A
LSQT1146.book  80 ページ  ２００６年１２月５日　火曜日　午前１０時４０分