Panasonic Va-824 Key Telephone System Installation And Programming Manual

							., 
,, --  s - 
~ .- ‘,, 
_. .) 
! 
. . 
25 
26 
:.  
						

							METHOD OF PROGRAMMING _.. 
Read the following paragraphs before proceeding to the actual programming instructions and procedures. 
These notes and procedures are intended to acclimate the programmer to the proper programmingsequencerequired prior to 
the actual programming. 
. 
Programming of initial set 
a Assure that the RAM switch is posi- 
tioned at “CLR” side. 
0 Set the power switch to the “ON” 
position. 
@ After about 5 seconds, assure that the 
DATA MONIT lamps is flashing. 
@ Change the RAM switch from the 
“CLR” side to “HOLD” side. 
The initial set programming is now com- 
pleted through the above operations. 
NOTE 
If you change the programming again, 
the RAM switch is not necessary 
switched over. 
5  
						

							. Method of programming 
All programming changes are made at 
Extension No. 10 and it isrecommend- 
ccl to use key telephone with a LCD 
display (VA-l 2022 or VA-12022-B). 
0 Press the ON/OFF button. The ON/ 
OFF indicator and MIC indicator 
lights up and a continuous tone is 
emitted. 
@ Press the ~]~~~l~~~](The continuous 
tone will stop) and then press the dial 
keyr/(iq (X: mode numbers 1 to 7) 
mode 1: System setting 
mode 2: COL setting 
mode 3: Key telephone setting 
mode 4: Incoming call ringing setting 
mode 5: Line/FF key setting 
mode 6: Restriction setting 
mode 7: Display time setting 
8 Press the program step numbers for 
the desired feature option. Refer to 
the PROGRAMMING TABLE for 
programmable feature option. 
@ Press the 
q key to store the memo- 
ry. The next program step will appear 
on the LCD display. When mode 
numbers of the programming features 
to be changed are the same, program 
step numbers of the programmings to 
be changed can be input after the 
registration. Therefore, the programm- 
ing changes can be performed continu- 
ously for the programming features 
having the same mode number. 
@ Press the ON/OFF button and display 
will return to the clock mode (ON/ 
OFF indicator and MIC indicator will 
go off). 
. Mode confirmation 
If you want to confirm the mode num- 
ber during programming, you can do 
so with the LCD disolav bv inouttina MIC indicator 
LCD display 
ON/OFF Button 
6  
						

							rogramming flowchart 
- 
- 
r 
1 * 000 
I ,l 
I (Set up for program mode) 
(Mode set) 
7  
						

							r 
,’ 
Names and phone numbers list 
00 118 136 54 
72 
I 
55 
173 I  01 19 37 
56 
174 
I 02 20 38 
03 21 39 
I 
58 176 
04 22 40 
05 23 41 
60 
178  06 24 42 
I 
61 179  07 25 43 
I 
62 180 
08 26 44 
63 
(81 
09 27 45 
I 
64 
I82  10 28 
-----------I- ----------------------- -~~ 
11 29 47 
67 
85 
I  13 31 49 
14 32 50 
15 33 51 
16 34 52 
17 
35 53 68 86 
69 87 
I 
70 88 
71 
89 
8  
						

							PROGRAMMING TABLE -. 
The set contents of all programming features should be recorded and stored according to the following table. 
System setting 
Outside access 
number from PBX 
Amount of time 
ause time store 
speed dial group A 
speed dial group B 
0 1 2 3 4 5 6 7 8 9 
No alarm tone 
Have alarm tone 
Long speech alarm 
*1os-0 
*108-l 
9  
						

							FEATURE 
I OPTION SELECTED 
I 
Automatic answering 
for incoming calls No auto answering Only handset auto answering 
Handset 8 ON/OFF key 
+109-o *109-1 
+109-z 
Ringing telephone 
for night time incom- 
ing calls Only night time ring set TEL will ring 
I COL ring set TEL will ring,too 
I 
+110-o +110-o 
I 
Hold recall No recall *111-o 
In the immediate After 30 set 
After 1 min 
Connection of 
door box Can not connect 
Can be connect 
Type of applicable 
sensors 
113-o 
Detect - close 
+113-1 
Detect - open 
1 
Sensor alarm 
stopping method 
114-o 
By sensor By handset (Off - hooking) 
1114-l 
SLT on-hooking 
jetection 
*115-o 
0.05 to 0.5sec 
+115-1 
0.05 to 1.2sec 
No connection Connection 
116-O -116-l 
No recall In the immediate After 30 set After 1 min After 2 min 
+117-o x117-1 
X117-2 x117-3 +i17-4 
Connection of DSS 
Hold recall for 
DSS TEL 
SMDR output No data out put Printer mode SMDR mode 
*201-o *201-1 1201-2 
300 BPS 600 BPS 1200 BPS 2400 BPS 4800 BPS 
9600 BPS 
X203-1 x203-2 x203-3 *203-4 
x203-5 *203-6 SMDR baud rate 
setting 7 
SMDR data 
configuration 7bit/l bit 7bitll bit 7bit/2bit 7bit/2bit Ebit/l bit 8bit/l bit 8bit/2bit 8bit/2bit 
Even No. Cdd No. Even No. Odd No. Even No. Odd No. Even No. Odd No. 
*204-1 x204-2 x204-3 x204-4 X204-5 *204-C x204-7 
*204-6 
*0101-o 
Non 1 + area code 
*0101-1 
1 + area code  Restriction when 
necessary to dial “1” 
for first digit 
Restriction on out- 
side calls using 
l or # keys *0102-o 
Restricted 
*0102-1 
Not restricted 
6 Not 8 digits 9 digits 10 digits 11 digits 12 digits 13 digits 14 digits 15 digits 16 digits 
0103-O 1 *0103-1 10103-2 *0103-3 X0103-4 0103-5 *0103-6 X0103-7 
I*o103-8 l*o103-9 
Restriction by num- 
ber of digits when 
making outside calls 
I I I I I I I I 
Outside dialing restricted Same content as that programmed outside 
dialing restrrction 
0104-O x0104-1 
Restriction on out- 
side calls using out- 
side lines on which 
incomin calls 
receive 8 
10  
						

							r 
6 
FEATURE OPTION SELECTED 
I 
Restriction release 
by specified dial 
code (1 + area) 
Restric$on release 
by specified dial 
code (1 + area) 
x 0113 
Restriction release 
by specified dial 
code (1 + area) 
+0114- 
Restriction release 
by specified dial 
code (1 + area) 1 0 11 1 2) 3 14 [ 576 17 18 19 1 Clear 
I I I I I I I I I I I I I I I I I I I I 
11  
						

							6 
FEATURE 
I OPTION SELECTED 
I 
+3striction release 
my specified dial 
mode (1 + area) 
0 1 2 3 4 5 6 7 8 9 
?estriction release 
,y specified dial Clear 
H 
mode (1 + area) 
I OI’I 
Restriction release 
3y specified dial 0 1 2 3 4 5 6 7 8 9 
mode (1 + area) 
Restriction release 
I I I I 
I I 
I I 
by specified dial 
0 1121314~5161718l9 
code (1 + area) 
12  
						

							COL setting 
2 
:oL 2 
Tel. No. : 
FEATURE 
OPTION SELECTED 
I 
I 
Dialing system for Tone 
Pulse 
t sutside calls *0201-o 
*0201-i 
Kind of outside line COL 
connected to the PBX 
system 
-0202-O 
*0202-1 
(COL or PBX) 
Specification for 
automatic connect- Not designated 
Designated 
ing to outside lines 
*0203-O 
*0203-l 
Tone dialing signal 80 m set 
240 m set 
duration 
*0204-O 
*0204-l 
Minimum pause for 80 m set 
160 msec 
tone dialing signal 
i 0205-O 
*0205-1 
2 
Tel. No. : 
OPTION 
SELECTED 
Dialing system for Tone dial 
Pulse dial 
outside calls 
*0101-o 
*0101-1 
Kind of outside line 
COL 
connected to the PBX 
system 
~0102-0 
*0102-1 
(COL or PBX) 
Specification for 
automatic connect- Not designated 
Designated 
ing to outside lines 
*0103-o 
*0103-1 
Tone dialing signal 
80 m set 
240 m set 
duration 
+0104-o 
x0104-1 
Minimum pause for 
80 m set 
160 msec 
tone dialing signal 
i 0105-O 
*0105-1 
6 set 
Detection time of a set 
ncoming ring signal 
r0107-0 
6 0107-l 
Detection time of 
Incoming ring signal +o2o7-o 6 set *0207-l 
8 set 
13