Panasonic UF 7100 YC User Manual

							51
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
582 XMT B Sub-address SEP (for Polling) 
transmission to a unit that has their 
DIS bit 47 (NSF bit 130) OFF.Sub-address transmission to a unit that 
has no Sub-address function.
601 XMT ADF Door was opened during ADF  
transmission.
623 XMT A No original was in the ADF. (Built-
in dialer engaged)Operator removed the original from the 
ADF after dialing was completed.
Original was not set properly in the ADF.
630 XMT or RCV
(Polling)B Redial count over. No dial tone detected. Sensor dial tone 
is not detected. (destination dependent)
Busy tone is detected. (destination 
dependent) T1 timer (35 ± 5 sec.) 
elapsed without a signal from the 
receiver.
631 XMT A STOP button was pressed during 
Auto Dialing.
634 XMT B Redial count over with no 
response or busy tone was not 
detected.
Note:
U.S.A. and Canadian models 
will redial only once if a busy 
tone is not detected.Telephone line cable is disconnected.
Wrong number is dialed.
SC or FXB PCB is abnormal.
638 XMT LAN Power turned Off with applicable 
data in memory or during 
communication.Power switched off. 
Power failure occurred.
700 XMT 
RCVPSTN
LANCommunication terminated by 
Operator pressing the STOP key.
711 RCV LAN Incorrect LDAP settings. LDAP Server Name, LDAP Login 
Name, LDAP Password and/or LDAP 
Search Base are incorrect.
712 XMT LAN Unknown email address replied 
from the Mail Server.Mail Server received an incorrect email 
address. (Dependent on Servers Mail 
application)
714 XMT 
RCVLAN LAN Interface error.
Cannot logon to the LAN.The 10Base-T/100Base-TX cable is not 
connected.
An unexpected LAN problem occurred.
Check the SC PCB connector.
715 XMT LAN TCP/IP connection timed out. Incorrect IP Address is set.
Verify the IP Address, Default Router IP 
Address, SMTP Server IP Address.
716 XMT LAN Cannot logon to the LAN. Incorrect SMTP Server IP Address is 
set.
No email application is activated on the 
Mail Server.
717 XMT LAN Incomplete SMTP Protocol 
transmission.Mail Server’s hard disk may be full.
Mail Server is defective. Fax Information Codes
Code Mode Phase Description of Problem Cause
Downloaded From ManualsPrinter.com Manuals 
						

							52
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
718 XMT LAN Page Memory Overflow occurred 
while receiving printing data.   The 
paper size selected within your 
application to print is larger than 
the paper size loaded in the 
Tray(s).Check the document size and 
resolution.
Ask originator to re-send in a supported 
size and resolution.
719 RCV LAN Received data via LAN is in a 
format that is not supported.Ask the originator to re-send with a 
supported file attachment:
* In a TIFF-F format.
* Image data conforming to A4/Letter 
size.
720 POP LAN Unable to connect with the POP 
Server.Incorrect POP Server address is set.
POP Server is down.
721 POP LAN Unable to login to the POP Server. Incorrect User Name or Password is 
set.
722 RCV LAN Failed to obtain the Network 
Parameters (such as: IP Address, 
Subnet Mask,  Default Gateway IP 
Address, etc.) from the DHCP 
server.LAN Cable is disconnected.
DHCP is not available.
(Contact the Network Administrator.)
725 XMT 
POPLAN DNS Server connection timed out. Incorrect DNS Server address is set.
DNS Server is down.
726 XMT 
POPLAN Received an error response from 
the DNS Server.Incorrect POP Server address is set.
Incorrect SMTP Server address is set.
727 XMT LAN Received an Error or No 
Response from the Remote
Internet Fax. (SMTP Direct XMT)Remote Internet Fax Errors: Busy or 
Job Number Overflow for Relay XMT. 
(Retry is possible)
728 XMT LAN Remote Internet Fax Errors: Memory 
Overflow or No Power. 
(Retry is not possible)
729 XMT LAN Failed to authenticate (SMTP 
AUTHENTICATION) when 
connecting with the SMTP server.SMTP AUTHENTICATION, User Name 
and/or Password are incorrect.
(Contact the Network Administrator.)
730 RCV LAN Unable to program the Internet 
parameters or the autodialer via 
Email from a PC.Verify that the Fax Parameter #158 is 
set to Valid.
731 RCV LAN Dialer full while Relayed 
Transmission Request was 
received.Dial buffer for manual number dialing 
(70 stations) is being used.
741 XMT, Polling PSTN Unable to dial Deleted the registered station name 
before dialing with Timer Controlled 
Communications, etc.
742 XMT
NYSE Fax 
ForwardPSTN
LANUnable to forward to the 
pre-programmed Supervisor‘s Fax 
machine or PC.
(USA and Canada Only)Communication error with the 
pre-programmed Supervisor‘s Fax 
machine or PC. 
(Busy, No Response, etc.)
800 Relay 
Comm.PSTN The machine was requested to 
relay a document but has no Relay 
Hub capability.Fax Information Codes
Code Mode Phase Description of Problem Cause
Downloaded From ManualsPrinter.com Manuals 
						

							53
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
Note:
When 2nd G3 option is installed, check FXB PCB or G3B PCB. 814 Conf. XMT 
Conf. Polling 
Relay 
Comm.PSTN The remote station does not have 
Relay XMT nor Confidential 
Communication capability.
815 Conf. RCV PSTN Mailbox full.
816 Conf.  Polled PSTN The received Polling Password did 
not match.
825 Conf. RCV
Conf. PolledPSTN Parameter settings of the remote 
station are not properly set.
870 MEM XMT 
MEM RCV PSTN
LANMemory overflow occurred while 
storing documents into memory.Memory overflow on the Fax.
871 MEM XMT 
MEM RCV PSTN
LANMemory management file number 
and page number exceeded while 
storing documents into memory.File number and page number overflow 
on the Fax.
880 - - File Access Error.
884 - - File Access Error.
961 RCV LAN Memory file access error. SC PCB is defective.
962 XMT PSTN Memory file access error. SC PCB is defective.
LAN Memory file access error. SC PCB is defective.Fax Information Codes
Code Mode Phase Description of Problem Cause
Downloaded From ManualsPrinter.com Manuals 
						

							54
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4 Service Modes
4.1. Service Modes (For Copier)
These Service Modes are provided to assist the technician in checking for abnormalities in the copier and a 
means of making adjustments to the Input/Output of major components.
Caution:
The factory default parameters are preset (country dependent) for optimum performance and in 
compliance with the local telecommunication regulations/standards, and do not need to be changed. 
Changing some of these parameters may cause the unit to be no longer compliant or become 
inoperable.
4.1.1. Service Mode Procedure
1. To select the Service Mode
The service mode is selected when “FUNCTION”, “ORIGINAL SIZE” and “3” keys are sequentially 
pressed, then F1 will appear in the display.
2. To exit the Service Mode
The service mode is reset when the “FUNCTION” and “CLEAR” keys are pressed sequentially.
4.1.2. Copier Service Mode Functions
Service Modes (For Copier)
Service 
ModeItem Function
F1 Self Test 00 Scanner LED Test This test is used for checking the 
Scanner LED.
01 LCD/LED Test This test is used for checking the LCD 
and LEDs.
02 Page Memory Test This test is used for checking the Page 
Memory.
03 Print Test Pattern 1 Prints the pattern for setting the Paper 
position alignment.
04 Print Test Pattern 2 Prints the Slant pattern for setting the 
Paper position alignment.
05 Print Test Pattern 3 Prints the Grid pattern for setting the 
Paper position alignment.
06 Print Test Pattern 4 Prints the pattern for setting the Duplex 
Paper position alignment.
F2 Single Copy Test One sheet is copied when the Start key 
is pressed.
F3 Continuous Copy Test Multi copies are made when the Start 
key is pressed.
F4 Input / Output Status Test The functioning of Input / Output items 
(selected item numbers) is checked.
F5 Function Parameters Various function settings (selected by 
code numbers) can be changed.
F6 Adjust Parameters Various function settings (selected by 
code numbers) can be adjusted.
F7 Electronic Counter Electronic Counters for Maintenance
F8 Service Adjustment Perform pseudo-operation of an item 
(selected by code numbers)
Downloaded From ManualsPrinter.com Manuals 
						

							55
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
F9 Unit Maintenance Fax Service Mode
Service Alert Tel #
Firmware Version
Print Device Info. Service Modes (For Copier)
Service 
ModeItem Function
Downloaded From ManualsPrinter.com Manuals 
						

							56
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
F5 / F6 Information List (Sample)
**********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01
F5-00 . . . . .      F5-50 Auto contrast adj. Yes 
F5-01 Frequency desired 60Hz  F5-51 Dept. Counter (COPY) No
F5-02 . . . . . F5-52 Dept. Counter (FAX) No
F5-03 . . . . . F5-53 2-sided auto shift No
F5-04 LSU off timer  5 Sec. F5-54 . . . . .
F5-05 . . . . . F5-55 . . . . .
F5-06 . . . . . F5-56 . . . . .
F5-07 . . . . . F5-57 . . . . .
F5-08 . . . . . F5-58 . . . . .
F5-09 . . . . . F5-59 Oper.add toner alarm Stop
F5-10 Exit Tray Limitation None F5-60 Auto Tray selection Yes
F5-11 . . . . . F5-61 . . . . .
F5-12 . . . . . F5-62 . . . . .
F5-13 Paper out Indicator On F5-63 . . . . .
F5-14 Paper size (Tray1) Letter-R F5-64 Dept. Counter (SCAN) No
F5-15 Paper size (Tray2) Letter-R F5-65 Dept. Counter (PRINT) No
F5-16 . . . . . F5-66 . . . . .
F5-17 . . . . . F5-67 . . . . .
F5-18 . . . . . F5-68 . . . . .
F5-19 . . . . . F5-69 Reduce N in 1 space No
F5-20 ADF Auto F5-70 PM cycle 120K
F5-21 . . . . . F5-71 . . . . .
F5-22 . . . . . F5-72 . . . . .
F6-00. . . . .F6-50 T/P Image Density 0
F6-01. . . . .F6-51 Photo Image Density 0
F6-02. . . . .F6-52. . . . .F6-03 Orig. Registration 0 F6-53 CCD Read Position 0
F6-04 Printer Registration 0 F6-54 Text Mode Contrast 0
F6-05
. . . . .F6-55 T/P Mode Contrast 0
F6-06. . . . .F6-56 Photo Mode Contrast 0
F6-07 Registration Void 6 F6-57. . . . .F6-08 Trail Edge Read Tim. 0 F6-58. . . . .F6-09 Trail Edge Prt Tim.        -6 F6-59. . . . .
F6-10 Side Adjust (Bypass) 0 F6-60. . . . .F6-11 Side Adjust (Tray 1) 0 F6-61. . . . .F6-12 Side Adjust (Tray 2) 0 F6-62. . . . .F6-13. . . . .F6-63 Lead Edge Read Tim. 0
F6-14. . . . .F6-64 Side Edge Read Adj. 0
F6-15. . . . .F6-65. . . . .F6-16. . . . .F6-66. . . . .F6-17. . . . .F6-67 ADF Image Density 0
F6-18. . . . .F6-68. . . . .F6-19. . . . .F6-69 Stamp Position Adj. 0
F6-20
. . . . .F6-70. . . . .F6-21. . . . .F6-71 ADF Read Scan Pos. 0
F6-22. . . . .F6-72 Original Lead ADF:S 0
  
**********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.02
Downloaded From ManualsPrinter.com Manuals 
						

							57
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
  2.FIRMWARE VERSION
      SC : BAT208xxAU  1.MACHINE INFORMATION
      MACHINE NAME : UF-8000
      MAC ADDRESS : 08002301D3E5
      SERIAL NUMBER : 
      SC BOOT : V803
      PNL : V010018
      SCANNER(SDR) : V00000
      PRINTER : V00029 
      FAX MODEM : Ver 0801
      G3B BOARD : 
      PDL FONT1 : CAV00000b
      SC2 : CAT120810aAU
  3.MEMORY CAPACITY
      PAGE MEMORY : 32 MB
      SORT MEMORY : 16 MB
      FAX MEMRY : 12 MB
  
  4.OPTION
      2nd PAPER FEED MODULE : No
      NETWORK SCANNER : Yes
      EMAIL : Yes
      PCL PRINTER : Yes
      2nd G3 Board : Yes (UF-8000/8100)
      
  5.ERROR LOG
      TOTAL PRINT COUNT : 503
  
  NO. DATE & TIME       ERROR CODE ERROR COUNT    NO. DATE & TIME      ERROR CODE ERROR COUNT
  --------------------------------------------------------------------------------
  01  MMM-dd-yyyy 11:11 J97        XX-00000008  
  02  MMM-dd-yyyy 11:31 J44        XX-00000140 
                                  (See Remarks) 
  --------------------------------------------------------------------------------
**********-MACHINE SETUP INFORMATION-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01
******************************* -                  - ***** -      0001- *********
Machine Setup Information List (Sample)
Remarks:
   XX-00000140
 00 : Printer Error
 02 : Scanner ErrorPage Count
 
-PANASONIC        -
Downloaded From ManualsPrinter.com Manuals 
						

							58
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
F7 Total Counter List (Sample)
F7-01 Key Operator ID Code : 000 
F7-02 Total Count : 295
F7-03 PM Count : 295
F7-04 Scanner PM Count :  61
F7-05 . . . . . :  
F7-06 OPC Drum Count : 295
F7-07 Process Unit Count  : 295
F7-08 ADF PM Count :    50
F7-09 . . . . . :
F7-10 . . . . . :
F7-11 Sheet Bypass Count : 147
F7-12 1st Paper Tray Count :  90
F7-13 2nd Paper Tray Count :   0
F7-14 . . . . . :
F7-15 . . . . . :
F7-16 2-Sided Count :  28
F7-29 . . . . . :
F7-30 A4R/LTR Count :  73
F7-31 . . . . . :
F7-32 FLS/LG Count :   0
F7-17 ADF Count :  26
F7-18 ADF Read Count :  26
F7-19 Scanner Count  :  61
F7-20 Scanner Read Count :  18
F7-21 Copy Rint Count :  59
F7-22 Copy Scan Count : 180
F7-23 PC Rint Count :   0
F7-24 PC Scan Count :   3
F7-24 Fax Transmit Count :  24
F7-24 Fax Receive Count :  27
F7-24 Fax Print Count :  21
Serial Number : **********-F7 TOTAL COUNTER LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01
Downloaded From ManualsPrinter.com Manuals 
						

							59
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
4.1.3. F4 Mode: Input/Output Status Test
Set the machine to service mode and press 4 key on the Keypad.
↓
Press the START key.
↓
Select “1:Check Input“ or “2:Check Output“ to activate the test then press START key.
↓
Press STOP key to cancel the test.
↓
When the “CLEAR” key is pressed, the selected code input will not be accepted.
↓
Press “FUNCTION” and “CLEAR” keys sequentially to exit the service mode.
1. Check Input 
2. Check Output 
Press the START key to start and press the STOP key to reset.F4 Mode (Check Input)
No. Function ConditionMessage Display
Remarks
76543210
030 ADF B2 Sensor Original is detected. 1
ADF Paper Exit Detection 
SensorOriginal is detected. 1
ADF Cover Open 
Detection SensorCover is open. 1
031 ADF Original Sensor Original is detected. 1
F4 Mode (Check Output)
No. Item Function Remark
120 Lamp When the SDR PCB P705-9 signal 
level changes to 0V from 3.5V, Lamp 
operates.The CIS shall be replaced 
as the Assembly
160 ADF Paper Feed Motor Rotating
(35% speed rotating)ADF paper feed motor rotates at 
35% speed. 
161 ADF Paper Feed Motor Rotating
(100% speed rotating)ADF paper feed motor rotates at 
100% speed. 
162 ADF Paper Feed Motor Rotating
(400% speed rotating)ADF paper feed motor rotates at 
400% speed. 
163 ADF Paper Feed Motor Reverse 
Rotating
(35% speed rotating)ADF paper feed motor rotates in 
reverse at 35% speed. 
164 ADF Paper Feed Motor Reverse 
Rotating
(100% speed rotating)ADF paper feed motor rotates in 
reverse at 100% speed. 
165 ADF Paper Feed Motor Reverse 
Rotating
(400% speed rotating)ADF paper feed motor rotates in 
reverse at 400% speed. 
Downloaded From ManualsPrinter.com Manuals 
						

							60
UF-7000/8000
NOV 2004 Ve r.  2 . 0
UF-7100/8100
175 ADF Stamp Solenoid When the ADF PCB CN25-2 signal 
level changes to 0V from +24V, 
Solenoid operates for 1 second. F4 Mode (Check Output)
No. Item Function Remark
Downloaded From ManualsPrinter.com Manuals