Panasonic Th 60pf30 Operating Instructions

							61
Using Network Function
This unit has a network function to control the network connected display with your computer.
Note:
To use the network function, set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” 
to “LAN”. (see page 53)
When “LAN” is set, the slot power is turned on, and power indicator is lit orange under the condition of power off with 
remote control (stand-by state), regardless of the “Slot power” setting. (see page 56)
Example of Network Connection
Command Control
Display (main unit, rear)
Hub or broadband routerLAN cable
(not supplied)
Notes:
•  Make sure the broadband router or hub supports 10BASE-T/100BASE-TX. 
•  To connect a device using 100BASE-TX, use “category 5” LAN cable. 
•  Touching the LAN terminal with a statically charged hand (body) may cause damage due to its discharge.
  Do not touch the LAN terminal or a metal part of the LAN cable. 
•  For instructions on how to connect, consult your network administrator.
Network function of the unit can control the unit in the same way as serial control from a network. 
Supported commands
Commands used in the serial control are supported. (see page 15)
Note:
Consult your local Panasonic dealer for detail instructions on command usage. COMPUTER
Less 
than 
3.9 inch
(10 cm)
Less 
than 
3.9 inch (10 cm)
Ferrite core 
(supplied)Ferrite core 
(supplied)
Installing the Ferrite core
Pull back the tabs
(in two places)Wind the cable 
twiceOpen
Press the cable 
through and close
 
						

							62
Using Network Function
PJLink™ Protocol
The network function of the unit conforms with PJLink™ class 1 and you can operate the following actions from your 
computer using PJLink™ protocol. 
• Display setup
•  Display status query
Supported commands
Commands to control the unit with PJLink™ protocol are shown in the table below.
PJLink™ security authentication
Set “Panasonic” for the PJLink™ password.
•  PJLink™ is a pending trademark in Japan, the United States, and other countries or areas. 
Command Control Remark
POWR Power controlParameter
0 = Standby  1 = Power “On”
POWR? Power status queryParameter
0 = Standby  1 = Power “On”
INPT Input switch
Parameter
See the parameter for command INST?
INPT? Input switch query
AVMT Shutter control Parameter
10 = Picture On (picture mute deactivated), 11 = Picture Off (picture on mute)
20 = Audio On (audio mute deactivated), 21 = Audio Off (audio on mute)
30 = Shutter mode Off (picture and audio mute deactivated)
31 = Shutter mode On (picture and audio on mute)
AVMT? Shutter control query Parameter
11 = Picture Off (picture on mute)
21 = Audio Off (audio on mute)
30 = Shutter mode Off (picture and audio mute deactivated)
31 = Shutter mode On (picture and audio on mute)
ERST? Error status query Parameter
First byte: Means fan error. 0 or 2.
Second byte: 0
Third byte: 0
Fourth byte: 0
Fifth byte: 0
Sixth byte: Means other error. 0 or 2.
Meaning of the 0 – 2 settings:
0 = Error is not detected, 2 = Error
LAMP? Lamp status query Not supported
INST? Input switch list query Parameter
Numbers 11 to 13 are depending on the slot installation condition
11: PC IN input (PC)
When a single input terminal board 
is attached
11: SLOT input (SLOT INPUT)
12: PC IN input (PC)
21: VIDEO input (VIDEO)
31: HDMI input (HDMI)When a dual input terminal board is 
attached
11: SLOT input (SLOT INPUT A)
12: SLOT input (SLOT INPUT B)
13: PC IN input (PC)
22:  COMPONENT/RGB IN input 
(COMPONENT)
32: DVI-D IN input (DVI)
NAME? Projector name query Returns empty character (no name information)
INF1? Manufacturer name query Returns “Panasonic”
INF2? Model name query Returns “TH-60PF30” (for 60-inch model)
INFO? Other information query Returns version number
CLSS? Class information query Returns “1”
 
						

							63
Unit Setup
Set each “NETWORK SETUP” setting and make sure to set the “CONTROL I/F SELECT” to “LAN”. (see page 53)
Computer Setup
Disable the proxy server settings and enable JavaScript. 
You can use a Web browser to control the unit and set up a network and password.
Access to the TOP screen of the Web browser control using a Web browser. To use the Web browser control, the unit and computer setups are required.
(Windows) (Macintosh)
Disable proxy server settings
1  Display [Internet Properties] window.
Click [Start] – [Control Panel] – [Network and Internet 
Connections] – [Internet Options].
2  Click the [Connections] tab and then [LAN Settings].
3  Deselect the [Use automatic con guration script] and 
[Use a proxy server for your LAN] boxes.
4  Click [OK].
Enable JavaScript
1  Display [Internet Properties] window.
Click [Start] – [Control Panel] – [Network and Internet 
Connections] – [Internet Options].
2  Set the security level on the [Security] tab to [Default 
Level]. Alternatively enable [Active scripting] from the 
[Custom Level] button.Disable proxy server settings
1  From the [Safari] menu, click [Preferences].
General screen is displayed.
2  From the [Advanced] tab, click the [Change 
Settings…] button next to [Proxies]. Click [Proxies] 
and set up a proxy server.
3  Deselect the [Web Proxy] and [Automatic Proxy 
Con guration] boxes.
4 Click [Apply Now].
Enable JavaScript
1  Display [Security] of Safari.
2  Select [Enable JavaScript] under [Web content].
1  Start your Web browser.
2  Enter the IP address set with the “NETWORK SETUP” of 
the unit. (see page 53)
3  Enter the user name and password when the 
Authentication screen is displayed.
Authentication screen
4  Click [OK].
After logged in, the TOP screen of the Web browser 
control is displayed. (see page 64)Notes:
  The password used here is the same password 
used for command control and the PJLink™ 
security authentication.
  Default user name and password are as follows:
User name: user1
Password: Panasonic
  The password can be changed on the Password 
Setup screen after logging in (see page 65). The 
user name cannot be changed.
  Under no circumstances, Panasonic Corporation 
or it's associated companies will ask customers 
their password directly.
Even if you are asked directly, please do not 
reveal your password.
Using Web Browser Control
Before Using Web Browser Control
Access from Web Browser
 
						

							64
Using Web Browser Control
TOP screen structure of the Web browser control
After logging in, the TOP screen of the Web browser control is displayed.
  Menu
Menu items are displayed. When a button is clicked, 
setup screen of each item is displayed.
Item Details
BASIC 
CONTROLBASIC CONTROL screen is displayed. 
(see below)
OPTION 
CONTROLOPTION CONTROL screen is 
displayed. (see below)
NETWORK 
SETTINGNetwork Setup screen is displayed.
(see page 65)
CHANGE 
PASSWORDPassword setup screen is displayed. 
(see page 65)
  According to the selected item from the main menu, 
setup status or set items are displayed.
  Network ID information
ID to identify the unit is displayed.
BASIC CONTROL screen OPTION CONTROL screen
Click BASIC CONTROL from the menu. Unit status and 
buttons to change settings are displayed.
Item Details
POWERSwitch ON/OFF of the unit power.
INPUT SELECTSwitch the input signals. Displayed 
buttons vary according to the 
connection status of the video 
device.
AUDIO MUTE Switch ON/OFF of the sound mute.
ASPECT Switch the screen modes  Click OPTION CONTROL from the menu. Command input 
 eld for command control of the unit is displayed.
Item Details
COMMANDEnter a command. Use the same 
command used for the serial control. 
(see page 15)
RESPONSE Response from the unit is displayed.
SEND Command is sent and run.
Note:
  After the settings are changed, it may take a while till the 
display status is displayed. Click BASIC CONTROL or OPTION CONTROL from the menu. Various controls of the unit can be set.
Display Control (BASIC CONTROL/OPTION CONTROL Screen)
 
						

							65
Notes:
•  To use a DHCP server, make sure the DHCP server 
is started.
•  During a DHCP server is used, IP ADDRESS, 
SUBNET MASK, and GATEWAY values cannot be 
entered.
•  When the set values are changed properly, 
“NETWORK SETTING CHANGED.” message and 
the changed set items are displayed.
Item Details
DHCPSet to ON when a DHCP server is 
used, or OFF when it is not used.
IP ADDRESS Enter an IP address.
SUBNET MASK Enter a subnet mask.
GATEWAY Enter a gateway address.
PORTEnter the port number used for 
command control. The available 
setting range is 1024 - 65535.
LAN SPEEDSet the connection speed of the LAN 
environment.
NETWORK IDSet the ID to identify this unit. The 
available setting range is 0 - 99.
SAVE Save the each set value.
Notes:
•  The default password is “Panasonic”.
•  Up to 32 alphanumeric characters can be used for a 
password.
•  When the password is changed properly, “Password 
has changed.” message is displayed.
Item Details
OLD 
PASSWORDEnter the old password.
NEW 
PASSWORDEnter the new password.
NEW 
PASSWORD
(RETYPE)Enter the password entered in “NEW 
PASSWORD” for con rmation.
SAVESave the new password. The 
con rmation screen is displayed.  
Click OK to change the password.
Click NETWORK SETTING from the menu. Various settings of a network can be set. For the details of the setting 
items, please check NETWORK SETUP under the SET UP of the unit. (see page 53)
Click CHANGE PASSWORD from the menu. Password to access the Web browser control can be set. When 
the password is changed in this screen, the password used for command control and the PJLink™ security 
authentication is also changed.
NETWORK SETTING (Network Setup Screen)
Password Setting (Password Setup Screen)
Using Web Browser Control
 
						

							66
Troubleshooting
Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Checks
Picture Sound
InterferenceNoisy SoundElectrical Appliances
Cars / Motorcycles
Fluorescent light
Normal PictureNo SoundVolume
(Check whether the mute function has been activated on the remote control.)
No PictureNo SoundNot plugged into AC outlet
Not switched on
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
No PictureNormal SoundIf a signal with a non-applicable color system format, or frequency is input, only the input 
terminal indication is displayed.
No ColorNormal SoundColor controls set at minimum level. (see page 29, 30)
COLOR SYSTEM (see page 50)
No remote control operations can be performed. Check whether the batteries have discharged completely and, if they have not, whether they 
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong 	 uorescent light.Check whether the remote control designed speci cally for use with the unit is being used. 
(The unit cannot be operated by any other remote control.)
A cracking sound is sometimes heard from the unit. If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing 
very slight contractions in response to changes in the room temperature.  There are no adverse 
effects on the performance or other aspects.
The top or bottom of the picture on the screen is cut 
off when I use the zoom function.Adjust the position of the picture on the screen.
Areas at the top and bottom of the screen where the 
image is missing appear when I use the zoom function.When using a video software program (such as a cinema size program) with a screen wider than one in 
the 16:9 mode, blank areas separate from the images are formed at the top and bottom of the screen.
I can hear sounds coming from inside the unit. When the power is turned on, a sound of the display panel being driven may be heard: This is 
normal and not indicative of malfunctioning.
Parts of the unit become hot.Even when the temperature of parts of the front, top and rear panels has risen, these temperature 
rises will not pose any problems in terms of performance or quality.
Power automatically turns off unexpectedly. Check the settings of “PC POWER MANAGEMENT”, “DVI-D POWER MANAGEMENT”, “NO 
SIGNAL POWER OFF” and “NO ACTIVITY POWER OFF” in the SET UP menu. Any of them 
may be set to “ON (ENABLE)”. (see page 42)
Power indicator is blinking in red. There is possibility of malfunction. Please contact an Authorized Service Center.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input 
signal. However, this is not a malfunction.
Plasma Display panel
Symptoms Check
The screen darkens slightly when bright pictures with 
minimal movements are shown.The screen will darken slightly when photos, still images of a computer or other pictures with minimal 
movements are shown for an extended period. This is done to reduce image retention on the screen 
and the shortening of the screen’s service life: It is normal and not indicative of malfunctioning.
It takes a while for the picture to appear. The unit digitally processes the various signals in order to reproduce esthetically pleasing 
images. As such, it sometimes takes a few moments for the picture to appear when the power 
has been turned on, when the input has been switched.
The  edges  of  the  images  	 icker. Due to the characteristics of the system used to drive the panel, the edges may appear to 	 icker 
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
The brightness on both sides of images in 4:3 mode 
changes.When viewing the side panels at the “BRIGHT” or “MID” setting, the brightness on both sides 
may change depending on the kind of program shown: This is normal and not indicative of 
malfunctioning.
Some parts of the screen do not light up. The plasma display panel is manufactured using an extremely high level of precision technology, 
however, sometimes some parts of the screen may be missing picture elements or have luminous 
spots. This is not a malfunction.
Image retention appearsDo not allow a still picture to be displayed for an extended period, as this can cause a permanent 
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images 
displayed in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from  xed image use is not 
an operating defect and as such is not covered by the Warranty.
This product is not designed to display  xed images for extended periods of time.
Whirring sounds can be heard from the display unit. The display unit is  tted with a cooling fan to dissipate heat generated during normal use. The 
whirring sound is caused by rotation of the fan and is not a malfunction.
 
						

							67
List of Aspect Modes
Aspect mode
Picture 
 Enlarged screenDescriptionAll Aspect: 
OnFactory setting
All Aspect: Off
16:9 FULL
The display of the pictures  lls the screen.
In the case of SD signals, pictures with a 4:3 aspect ratio are 
enlarged horizontally, and displayed. This mode is suited to 
displaying anamorphic pictures with a 16:9 aspect ratio.
14:9 –
Letterbox pictures with a 14:9 aspect ratio are enlarged 
vertically and horizontally so that their display  lls the 
screen vertically and is slightly smaller than the screen 
horizontally. The top and bottom edges of the pictures are 
cut off. Side panels are displayed at the left and right edges 
of the screen.
Just
JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally 
so that the picture distortion is minimized. The display of 
the areas around the left and right edges of the screen is 
slightly elongated. Just1
Just2 JUST
Pictures with a 4:3 aspect ratio are enlarged horizontally 
so that the picture distortion is minimized. The left and right 
edges of the pictures are cut off. The display of the areas 
around the left and right edges of the screen is slightly 
elongated.
4:3
4:3
Pictures with a 4:3 aspect ratio are displayed with their 
original aspect ratio. Side panels are displayed at the left 
and right edges of the screen.
4:3 (1)
4:3 (2) 4:3
Pictures with a 4:3 aspect ratio are displayed with their 
original aspect ratio. The left and right edges of the pictures 
are masked by side panels.
4:3 Full H-FILL
Pictures with a 4:3 aspect ratio are enlarged horizontally so 
that their display  lls the screen. The left and right edges of 
the pictures are cut off.
Zoom
ZOOM
Letterbox pictures with a 16:9 aspect ratio are enlarged 
vertically and horizontally so that their display   lls the screen. 
The top and bottom edges of the pictures are cut off.
Zoom1
Zoom2 ZOOM
Letterbox pictures with a 16:9 aspect ratio are enlarged 
vertically and horizontally so that their display   lls the screen. 
The top and bottom edges as well as the left and right edges 
of the pictures are cut off.
Zoom3 –
Letterbox pictures with a 2.35:1 aspect ratio are enlarged 
vertically and horizontally so that their display  lls the screen 
vertically and is slightly larger than the screen horizontally. 
The top and bottom edges as well as the left and right edges 
of the pictures are cut off.
 
						

							68
Applicable Input Signals
*Mark: Applicable input signal
Signal nameHorizontal frequency 
(kHz) Vertical frequency 
(Hz) COMPONENT / RGB IN 
/ PC IN
(Dot clock (MHz))DVI-D IN
(Dot clock 
(MHz))HDMI
1   525  (480) / 60i  15.73 59.94 *  (13.5) *  (27.0) *
2   525  (480) / 60p  31.47 59.94 *  (27.0)   
5 * (27.0) *
3   625  (575) / 50i  15.63 50.00 *  (13.5)
4   625  (576) / 50i 15.63 50.00 *  (27.0) *
5   625  (575) / 50p  31.25 50.00 *  (27.0)
6   625  (576) / 50p  31.25 50.00 *  (27.0) *
7   750  (720) / 60p  45.00 60.00 *  (74.25) *  (74.25) *
8   750  (720) / 50p  37.50 50.00 *  (74.25) *  (74.25) *
9   1,125  (1,080) / 60p  67.50 60.00 *  (148.5) 
1 * (148.5) *
10   1,125  (1,080) / 60i  33.75 60.00 *  (74.25) 
1 * (74.25) *
11   1,125  (1,080) / 50p  56.26 50.00 *  (148.5) 
1 * (148.5) *
12   1,125  (1,080) / 50i  28.13 50.00 *  (74.25) 
1 * (74.25) *
13   1,125  (1,080) / 24sF  27.00 48.00 *  (74.25) 
2
14   1,125  (1,080) / 30p  33.75 30.00 *  (74.25) 
1 * (74.25)
15   1,125  (1,080) / 25p  28.13 25.00 *  (74.25) 
1 * (74.25)
16   1,125  (1,080) / 24p  27.00 24.00 *  (74.25) 
1 * (74.25) *
17   1,250  (1,080) / 50i  31.25 50.00 *  (74.25) 
3
18   2,048 × 1,080 / 24sF 
7 27.00 48.00
19   2,048 × 1,080 / 24p 
7 27.00 24.00
20   640 × 400 @70 Hz 31.46 70.07 *  (25.17)
21   640 × 480 @60 Hz  31.47 59.94 *  (25.18) 
6 * (25.18) *
22   640 × 480 @72 Hz  37.86 72.81 *  (31.5)
23   640 × 480 @75 Hz  37.50 75.00 *  (31.5)
24   640 × 480 @85 Hz  43.27 85.01 *  (36.0)
25   800 × 600 @56 Hz  35.16 56.25 *  (36.0)
26   800 × 600 @60 Hz  37.88 60.32 *  (40.0) *  (40.0) *
27   800 × 600 @72 Hz  48.08 72.19 *  (50.0)
28   800 × 600 @75 Hz  46.88 75.00 *  (49.5)
29   800 × 600 @85 Hz  53.67 85.06 *  (56.25)
30   852 × 480 @60 Hz  31.47 59.94 *  (33.54) 
6*
(34.24) *
31   1,024 × 768 @50 Hz  39.55 50.00 *  (51.89) *
32   1,024 × 768 @60 Hz  48.36 60.00 *  (65.0) *  (65.0) *
33   1,024 × 768 @70 Hz  56.48 70.07 *  (75.0)
34   1,024 × 768 @75 Hz  60.02 75.03 *  (78.75)
35   1,024 × 768 @85 Hz  68.68 85.00 *  (94.5)
36   1,066 × 600 @60 Hz  37.64 59.94 *  (53.0) *  (53.0) *
37   1,152 × 864 @60 Hz  53.70 60.00 *  (81.62) *
38   1,152 × 864 @75 Hz  67.50 75.00 *  (108.0)
39   1,280 × 768 @60 Hz 47.70 60.00 *  (80.14)
40   1,280 × 960 @60 Hz  60.00 60.00 *  (108.0)
41   1,280 × 960 @85 Hz  85.94 85.00 *  (148.5)
42   1,280 × 1,024 @60 Hz  63.98 60.02 *  (108.0) *  (108.0) *
43   1,280 × 1,024 @75 Hz  79.98 75.03 *  (135.0)
44   1,280 × 1,024 @85 Hz  91.15 85.02 *  (157.5)
45   1,366 × 768 @50 Hz  39.55 50.00 *  (69.92) *
46   1,366 × 768 @60 Hz  48.36 60.00 *  (86.71) *  (87.44) *
47   1,400 × 1,050 @60 Hz  65.22 60.00 *  (122.61) *
48   1,600 × 1,200 @60 Hz  75.00 60.00 *  (162.0) *  (162.0) *
49   1,600 × 1,200 @65 Hz  81.25 65.00 *  (175.5)
50   1,920 × 1,080 @60 Hz 67.50 60.00 *  (148.5) 
4 * (148.5) *
51   1,920 × 1,200 @60 Hz 74.04 59.95 *  (154.0) *
52   Macintosh13”  (640 × 480)  35.00 66.67 *  (30.24)
53   Macintosh16”  (832 × 624)  49.72 74.54 *  (57.28)
54   Macintosh21”  (1,152 × 870)  68.68 75.06 *  (100.0)
1: Based on SMPTE 274M standard.     2: Based on SMPTE RP211 standard.
3: Based on SMPTE 295M standard.     4: The input signal is recognized as 1,125 (1,080) / 60p.
5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60Hz signal.
6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
7:  Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal Board 
(TY-FB11DHD) is installed.
Note: Signals without above speci cation may not be displayed properly.
 
						

							69
Applicable Input Signals
1/2
SIGNAL
EXTENDED LIFE SETTINGS
INPUT LABEL
SET UP
OFF
STANDBY SAVE
ON
PC POWER MANAGEMENTONDVI-D POWER MANAGEMENTOFF
OSD LANGUAGEENGLISH (
US) COMPONENT/RGB-IN SELECT
RGB SCREENSAVER
POWER SAVENO SIGNAL POWER OFFENABLENO ACTIVITY POWER OFFDISABLE
3D SETTINGS
This function allows you to reset the unit to the factory setting.
Shipping condition
1
4
5
6Press to display the SET UP menu.
Press to select “OSD LANGUAGE”.
Press for more than 3 seconds.
Press to select “Shipping”.
Press to display the Shipping menu.
Press to select “YES”.
Press to con rm.
Wait for 10 seconds.
Press the power switch (
) on main unit to turn the power off.
[from the unit]
1  Press the MENU button till the SET UP menu is displayed.
2  Press the Volume Up “+” or Down “–” button to select “OSD LANGUAGE”.
3  Press and hold the ENTER button till the Shipping menu is displayed.
4  Press the Volume Up “+” or Down “–” button to select “YES”.
5  Press the ENTER button and wait for 10 sec.
6  Press the power switch (
) on main unit to turn the power off.
2
3
Options
Shipping
ShippingYESNO
Video input (VIDEO)
Signal nameHorizontal Vertical
frequency(kHz) frequency(Hz)
1 NTSC 15.73 59.94
2 PAL 15.63 50.00
3 PAL60 15.73 59.94
4 SECAM 15.63 50.00
5 Modi ed NTSC 15.73 59.94
 
						

							70
Command list of Weekly Command Timer
No. Command Control details
1 AAC:MENCLR Audio Menu (CLEAR)
2 AAC:MENDYN Audio Menu (DYNAMIC)
3 AAC:MENSTD Audio Menu (STANDARD)
4 AAC:SURMON Surround (ON)
5 AAC:SUROFF Surround (OFF)
6 AMT:0 Audio Mute (OFF)
7 AMT:1 Audio Mute (ON)
8 
9 
10 AVL:00 Audio Volume (00)
11 AVL:10 Audio Volume (10)
12 AVL:20 Audio Volume (20)
13 AVL:30 Audio Volume (30)
14 AVL:40 Audio Volume (40)
15 AVL:50 Audio Volume (50)
16 AVL:60 Audio Volume (60)
17 DAM:FULL Aspect (FULL)
18 DAM:JUST Aspect (JUST)
19 DAM:NORM Aspect (4:3)
20  
21 DAM:ZOOM Aspect (ZOOM)
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39 IMS:SL1 Input select (SLOT INPUT)
40 IMS:S1A Input select (SLOT INPUT A)
41 IMS:S1B Input select (SLOT INPUT B)
42 IMS:VD1 Input select (VIDEO)
43 IMS:YP1 Input select (COMPONENT)
44 IMS:HM1 Input select (HDMI)
45 IMS:DV1 Input select (DVI)
46 IMS:PC1 Input select (PC)
47  
48  
49  
50  
51  
52  
53  
54  
55OSP:SCR0 Screen Saver SCROLLING BAR ONLY (OFF)
56OSP:SCR1 Screen Saver SCROLLING BAR ONLY (ON)
57 POF Power OFF
58 PON Power ON
59SSC:FNC0 Screen Saver function (SCROLLING BAR ONLY)
60SSC:FNC1 Screen Saver function (NEGATIVE IMAGE)
61SSC:MOD0 Screen Saver (Mode (OFF))
62SSC:MOD3 Screen Saver (Mode (ON))
63
VMT:0
Picture Mute (OFF)
64
VMT:1
Picture Mute (ON)
  Picture Mute cannot be unlocked by powering off/on with the remote control. Turn off and on again with the button on 
the unit or enter the command VMT:0 to unlock Picture Mute.