Panasonic Th 42ps10rs Operating Instructions

							1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
41
Options Adjustments
1
2
3
5Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from 
Options menu.
4
6
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff   PC   INPUT1   INPUT2   INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 13).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
(For TH-42PS10RK/S)
 Ofrecido por www.electromanuales.com
 
						

							1/3Options
Off-timer function
INPUT lock
Studio W/B
Advanced PIP
Display size Initial VOL level
Maximum VOL level Initial INPUT Onscreen display
Off
Off
Off
Off Enable
On
Off
0
Off Off
0
42
Options Adjustments
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.• You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press  button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” 
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• 
You can hear the changed volume regardless of your volume setting before opening the options menu if 
you adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff   PC   INPUT1   INPUT2   INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
•  In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value 
input in the single screen display mode.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On:  Sets the colour temperature for TV studio.
Note:  Valid only when the low is set as colour temperature on screen adjustment.
Advanced PIP
Off On
Off:  Sets normal two screen display mode (see page 20).
On:  Sets Advanced PIP mode (see page 21).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
• 
,  buttons are unavailable during Advanced PIP mode operation.
Display size
Off On
Adjusts the image display size on screen.
Off:  Sets the normal image display size on screen.
On:  Sets the image display size approximately 95 % of the normal image display.
       Off       On
   
Notes:
• This setting is valid only when the input signals are as follows; 525i, 525p, 625i, 625p, 750/60p, 
750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p, 1250/50i (Component 
Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When “Display size” is set to “On”, Pos. /Size adjustment cannot be used. 
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
 Ofrecido por www.electromanuales.com
 
						

							2/3Options
OffOffOff
Off
0
Remote ID
Serial ID ID select Button lock
Remocon User level
3/3Options
Off
Off
Off V. lnstallation
Rotate
Slot1 Serial Slot Select Slot power
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
 button on main unit together with  button on the remote control and hold for more than 5 seconds. 
The “SHIPPING” menu is displayed and the lock is released when it disappears.Item Effect Adjustments
Button lockOff  MENU&ENTER  On 
Off:  All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
  Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Remocon 
User levelOff   User1   User2   User3 
Off:  You can use all of the buttons on the remote control.
User1:
 You can only use , , , , , , ,  buttons on the remote 
control.
User2:
 You can only use , , buttons on the remote control.
User3: Locks all the buttons on remote control.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Item Effect Adjustments
Slot PowerOff  Auto  On 
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the 
standby state regardless of the slot power setting.
V.Installation
Off On
Off:  Sets fan to the horizontal installation mode.
On:  Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Vertical installation is available without this mode setting.
• Turn up the power switch for the upward direction when you set Display vertically.
Rotate
Off On
Off:  Does not rotate the image.
On:  Rotates the image 180 degrees.
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note:  The setting of an external command can be set only from the fi xed serial terminal (see page 
10).
43 Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							Options 
Weekly Command Timer 
Initial VOL level 
1/3 
 
Off  Off 
0  0 Maximum VOL level Off INPUT lock Off Button lock Off Remocon User level Off Advanced PIP 
Initial INPUT  Onscreen display On 
O f f 
44
Item Effect Adjustments
Weekly 
Command 
TimerSets Weekly Command Timer. (see page 48)
Onscreen 
display
On Off
On:  Displays all the following on screen.
• Power on display
• Input signal switch display
• No signal display
• Mute and the remaining time of off-timer after 
 was pressed.
Off:  Hides all the items above from view.
Initial INPUTOff  PC  INPUT1  INPUT2  INPUT3 
Adjusts the input signal when the unit is turned on.
Notes:
• Only the adjusted signal is displayed. (see page 13).
• Signal can be displayed when the Terminal board is installed.
• This menu is available only when “INPUT lock” is “Off”.
• When a dual input terminal board is attached, A or B is displayed depending on the selected 
input signal. (Ex. INPUT1A, INPUT1B)
1
2
3
5Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold until the Options menu is displayed.
Press to select your preferred menu.
Press to adjust the menu.
Press to exit from 
Options menu.
4
6
(For TH-42PH10RK/S, TH-50PH10RK/S, TH-58PH10RK)
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							Options 
On Weekly Command Timer Onscreen display Off Initial INPUT 
1/3 
 
Maximum VOL level  Initial VOL level 
Button lock 
INPUT lock 
Advanced PIP 
Remocon User level 
Off  Off 
0  0 
Off 
Off 
Off 
Off 
45
Item Effect Adjustments
Initial VOL 
level
Off On
Press  button to adjust the volume when the unit is turned on.
Off  On
Off:  Sets normal volume.
On:  Sets your preferred volume.
Notes:
• 
When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.• You can hear the changed volume regardless of your volume setting before opening the options menu if you 
adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Maximum VOL 
level
Off On
Press  button to adjust the maximum volume.
Off  On
Off:  Sets auto maximum volume.
On:  Sets your preferred maximum volume.
Notes:
• If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” 
automatically becomes the same as the “Maximum VOL level”.
• The volume display can go up to 63 regardless of the settings.
• 
You can hear the changed volume regardless of your volume setting before opening the options menu if you 
adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu.
INPUT lockOff   PC   INPUT1   INPUT2   INPUT3
Locks the input switch operation.
Notes:
• Only the adjusted signal is displayed (see page 13).
• Signal can be displayed when the Terminal board is installed.
• Input switch can be used when this is set to “Off”.
• In two screen display mode, if anything other than “Off” is set, the value will be fi xed as the value 
input in the single screen display mode.
•  When a dual input terminal board is attached, A or B is displayed depending on the selected input 
signal. (Ex. INPUT1A, INPUT1B)
Button lockOff  MENU&ENTER  On 
Off:  All the buttons at the bottom of the main unit can be used.
MENU & ENTER:
  Locks 
MENU and ENTER/ buttons on bottom face of main unit.
On:  Locks all the button on bottom face of main unit.
Sets Button lock with the unit buttons in the following procedure.
Off:  Press 
 four times→Press INPUT four times→Press  four times→Press ENTER/MENU & ENTER:  Press ENTER/ four times→Press  four times→Press INPUT four times→Press ENTER/On:  Press  four times→Press ENTER/ four times→Press  four times→Press ENTER/
Remocon 
User levelOff  User1  User2  User3 
Off:  You can use all of the buttons on the remote control.
User1: You can only use , , , , , , ,  buttons on the remote 
control.
User2:
 You can only use , , buttons on the remote control.
User3: Locks all the buttons on remote control.
Advanced PIP
Off On
Off:  Sets normal two screen display mode (see page 20).
On:  Sets Advanced PIP mode (see page 21).
Notes:
• When “INPUT lock” is “On”, you cannot use all the two screen display functions.
• 
,  buttons are unavailable during Advanced PIP mode operation.
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							Options
EnableOff-timer function
NormalInitial Power Mode0ID selectOffRemote IDOffSerial IDOffDisplay sizeOffStudio W/BOffStudio Gain
2/3
46
Item Effect Adjustments
Off-timer 
function
EnableDisable
Enable:  Enables the “Off-timer function”.
Disable:  Disables the “Off-timer function”.
Note:    When “Disable” is set, the Off-timer is cancelled.
Initial Power 
ModeNormal  Standby  On
Sets the power mode of the unit for when the power recovers from failure or after plugging off 
and in again.
Normal:  Power returns in as the same state as before the power interruption.
Standby:  Power returns in standby mode. (Power Indicator : red/orange)
On:    Power returns in power On. (Power Indicator : green)
Note:    When using multiple displays, “Standby” is preferred to be set in order to reduce a 
power load.
ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.
Set value range: 0 - 100
(Standard value: 0)
Remote ID
Off On
Off:  Disables ID remote control functions. You can use normal remote control operations.
On:  Enable ID remote control functions.
Serial ID
Off On
Sets the panel ID Control.
Off:  Disables external control by the ID.
On:  Enables the external control by the ID.
Display size
Off On
Adjusts the image display size on screen.
Off:  Sets the normal image display size on screen.
On:  Sets the image display size approximately 95 % of the normal image display.
    Off       On
  
Notes:
• This setting is valid only when the input signals are as follows; 
 
NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD)) 525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 
1125/30p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)
• This setting is invalid when two screen display, digital zoom or Multi screen is selected.
• When “Display size” is set to “On”, Pos. /Size adjustment cannot be used. 
• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.
Studio W/B
Off On
Off:  Nullify all the settings adjusted.
On:  Sets the colour temperature for TV studio.
Note:  Valid only when the low is set as colour temperature on screen adjustment.
Studio Gain
Off On
Sharpens the contrast for a better view when a part of the image is too light to see.
Off:  Disables “Studio Gain”.
On: Enables “Studio Gain”.
Note:  This setting is valid only when the input signals are as follows:
    Component Video, RGB (analog), SDI, HDMI
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							3/3Options
Off
Off
Off V. lnstallation
Rotate
Slot1 Serial Slot Select Slot power
Normalization
When both main unit buttons and remote control are disabled due to the “Button lock”, “Remocon User level” or “Remote 
ID” adjustments, set all the values “Off” so that all the buttons are enabled again.
Press the 
 button on main unit together with  button on the remote control and hold for more than 5 seconds. 
The “SHIPPING” menu is displayed and the lock is released when it disappears.
47
Item Effect Adjustments
Slot PowerOff  Auto  On 
Off:  Power is not transmitted to the slot power.
Auto:  Power is transmitted to the slot power only when main power is on.
On:  Power is transmitted to the slot power when main power is on or in the standby state.
Note:  In some cases, power is transmitted to the slot power when main power is on or in the 
standby state regardless of the slot power setting.
V.Installation
Off On
Off:  Sets fan to the horizontal installation mode.
On:  Sets fan to the vertical installation mode.
Notes:
• This functions when display is turned on.
• Turn up the power switch for the upward direction when you set Display vertically.
Rotate
Off On
Off:  Does not rotate the image.
On:  Rotates the image 180 degrees.
Serial Slot 
SelectSlot1  Slot2   Slot3
Selects the slot which communicates serial.
Note: 
The setting of an external command can be set only from the fi xed serial terminal (see page 10).
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							Options 
On Weekly Command TimerOnscreen display 
1/3 
 
Weekly Command Timer 
On Program1Function Monday 
Program3Tuesday --- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
Program1On Monday Function 
Program3Tuesday 
--- Wednesday Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Program3Thursday --- Friday Program6Saturday Program4Sunday Program Edit 
Weekly Command Timer 
8:00 
10:30 01
02
1/8
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
Program number
48
You can set 7-day timer programming by setting time and command.
Note: 
Before setting Weekly Command Timer, set PRESENT TIME Setup. (see page 27)
Press to select Function.
Press to select “On”.
Note:
•  When Function is set to On, Set up TIMER 
(see page 28) is unavailable and Interval / 
Time Designation in Mode of Screensaver 
(see page 29) cannot be selected.
1
Press to select a day.
Press to select a program number.
Note:
• You can set the program from 1 to 7.
--- indicates unset.
2
Press to select Program Edit.
Press to show the Program Edit screen.
Press to select Program.
Press to change the program numbers (1-7).
4 3
Press ACTION  (  ) button
Program Edit screen
Options Adjustments
Weekly Command Timer (for TH-42PH10RK/S, TH-50PH10RK/S, TH-58PH10RK)
 Ofrecido por www.electromanuales.com
 
						

							Weekly Command Timer 
20:00 
20:30 57 
58 
8/8 
 
22:00 59 --:-- 60 --:-- 
--:-- 61 --:-- 62 --:-- AVL:00 
DAM:NORM 
POF 
--- 
--- 
---  --- 
--- 63 64 
1Program
Weekly Command Timer 
8:00 
10:30 
02 01
1/8 
 
--:-- 03--:-- 04--:-- 
--:-- 0512:00 069:12 PON
IMS:SL1 
--- 
--- 
--- 
---  DAM:ZOOM 
AVL:10 0708
1Program
Weekly Command Timer 
0210:30 Command No Time IMS:SL1 Command 
1Program
Weekly Command Timer 
Command 
02Command No 
IMS:SL1 10:30 Time 
1Program
49
Press to select a command number.
Press to show the previous / next command 
pages (1-8) of the selected program.
Press to show the command setting screen.
5
Press to select Command No.
Press to select a command number.
6
Press to select Time / Command.
Press to set each item.
Time: Set the time to execute a command 
program.
      Pressing “ ” or “ ” button once changes “Time” 1 minute.
          Pressing “ ” or “ ” button continuously changes “Time” by 15 minutes.
Command:Select a command to execute at the set time. This unit has 64 commands 
to set. (see page 53)
Notes:
• 
Command is performed in order of execution time, regardless of the command number.
•  If a command execution time overlaps with that of other commands, these commands 
are performed in number order.
• Pressing 
, Time becomes --:-- and Command becomes ---.
7
Note:
• Press 
 to return to the previous screen.Command setting screen Command (--- indicates unset)
Set time of timer(--:-- indicates unset)
Command numbers
Options Adjustments
 Ofrecido por www.electromanuales.com
 
						

							1/2 
Signal 
PC 
Off
Standby save Off
Power management Off 
Auto power off Off 
OSD Language English (
UK)  Component/RGB-in select 
RGB 
Input label 
Power save 
Setup 
SHIPPINGYES
50
Shipping condition
This function allows you to reset the unit to the factory setting.
1
2
3
4
Press to display the Setup menu.
Press to select “OSD Language”.
Press and hold till the SHIPPING menu is 
displayed.
Press to select “YES”.
Press to confi rm.
[from the unit]
1  Press the MENU button till the Setup menu is displayed.
2  Press the Volume Up“+” or Down“–” button to select “OSD Language”.
3  Press and hold the ENTER button till the SHIPPING menu is displayed.
4  Press the Volume Up“+” or Down“–” button to select “YES”.
5  Press the ENTER button and wait for 10 sec.
Note:
Press the R button to return to Setup menu when SHIPPING menu is displayed.
 Ofrecido por www.electromanuales.com