Panasonic System Controller Wv Cu650 Wv Cu950 Calibration Guide

							2-1
CALIBRATION PROCEDURE
1. Pan / Tilt Calibration
3The Pan / Tilt Calibration is required in the fol-
lowing cases.
•After replacing the EEPROM, Pan / Tilt and Zoom wheel
Calibration is required.
(Default software data will be stored in the EEPROM
automatically.)
•In the case of changing of the combination of the Main
Unit and the 3D Joystick Unit as shown in the Exploded
View(10/10).
•In the case of replacing of the Joystick Board (PCB 5) or
VR101 and other parts on it.
•In case of replacing the Main Board (PCB 1) or EEPROM
(IC6 ) and other parts on it.
•In case that calibrated data has been changed by opera-
tion mistake.
3Procedure
1.  Turn off the power.
2.  To execute the Pan / Tilt Calibration Mode, Turn on the
power while pressing the [9] and [MON(ESC)] keys
simultaneously.
The LCD on the Front Panel will indicate as right.
3.  Enter the administrator password.
Notes: • The factory default is "650".
• To delete a character, press the CLEAR button.
Note: Just example, It depends on Unit
4.  Press the [CAM(SET)] key.
The LCD on the Front Panel will indicate as right.
5.  Press the [CAM(SET)] key for the starting adjustment.
The LCD on the Front Panel will indicate as right.
6.  Turn and keep the Joystick to fully upper side.
The LCD on the Front Panel will indicate as right.7.  Press the [CAM(SET)] key while turning the Joystick to
upper side.
The LCD on the Front Panel will indicate as right.
8.  Turn and keep the Joystick to fully down side.
The LCD on the Front Panel will indicate as right.
9.  Press the [CAM(SET)] key while turning the Joystick to
down side.
The LCD on the Front Panel will indicate as right.
10. Return the Joystick to center.
The LCD on the Front Panel will indicate as right.
Note : It needs your hand to release with flipping.
11.  Press the [CAM(SET)] key.
The LCD on the Front Panel will indicate as right.
12.  Turn and keep the Joystick to fully right side.
The LCD on the Front Panel will indicate as right.
13.  Press the [CAM(SET)] key while turning the Joystick to
right side.
The LCD on the Front Panel will indicate as right.
Pan/Tilt Calibration 
Admin Password _____
U:F2 D:09 TC:78    0 
R:E6 L:06 PC:75    0
U:__ D:__ TC:__   72 
R:__ L:__ PC:__    
U:__ D:__ TC:__   F0 
R:__ L:__ PC:__    
U:F1 D:__ TC:__   7D 
R:__ L:__ PC:__    
U:F1 D:__ TC:__   08 
R:__ L:__ PC:__    
U:F1 D:08 TC:__   08 
R:__ L:__ PC:__    
U:F1 D:08 TC:__   70 
R:__ L:__ PC:__    
U:F1 D:08 TC:70   79
R:__ L:__ PC:__    
U:F1 D:08 TC:70    
R:__ L:__ PC:__   F1
U:F1 D:08 TC:70    
R:F0 L:__ PC:__   F0
Blinking 
						

							2-2 14.  Turn and keep the Joystick to fully left side.
The LCD on the Front Panel will indicate as right.
15.  Press the [CAM(SET)] key while turning the Joystick to
left side.
The LCD on the Front Panel will indicate as right.
16. Return the Joystick to center.
The LCD on the Front Panel will indicate as right.
Note : It needs your hand to release with flipping.
17.  Press the [CAM(SET)] key.
The LCD on the Front Panel will indicate as right,
18.  Confirm the following.
•  The LCD on the Front Panel will indicate 64 steps of
each change, when it turns to the upper and lower sides
and right.
• The value of Pan and Tilt on the LCD will return to
ZERO, when the Joystick is returned to the center.
19.  Turn off the power to finish the calibration.
2. Zoom Wheel Calibration
3The Zoom Wheel Calibration is required in the
following cases
• In case of replacing the Joystick Unit.
• In case of disassembling the Joystick Unit.
• In case of replacing the Main Board.
• In case of replacing the EEPROM (IC6 on the Main
Board).
• In case that calibrated data has been changed by oper-
ation mistake.
3Procedure
1.  Turn off the power.
2.  To execute the Pan / Tilt Calibration Mode, Turn on the
power while pressing the [8] and [MON(ESC)] keys
simultaneously.
The LCD on the Front Panel will indicate as right.
3. Enter the administrator password.
Notes: • The factory default is "650".
• To delete a character, press the CLEAR button.
Note: Just example, It depends on Unit.
4. Press the [CAM(SET)] key.
The LCD on the Front Panel will indicate as right.
5. Press the [CAM(SET)] key for the starting adjustment.
The LCD on the Front Panel will indicate as right.
6.  Turn and keep the Zoom Wheel to fully right (TELE)
side.
The LCD on the Front Panel will indicate as right.
U:F1 D:08 TC:70    
R:F0 L:__ PC:__   07
U:F1 D:08 TC:70    
R:F0 L:07 PC:__   07
U:F1 D:08 TC:70    
R:F0 L:07 PC:__   76
U:F1 D:08 TC:70    0
R:F0 L:07 PC:76    0
U:F1 D:08 TC:70    0
R:F0 L:07 PC:76    0
Zoom Calibration 
Admin Password _____
T:BC W:45 ZC:7D    0
T:__ W:__ ZC:__   84 
T:__ W:__ ZC:__   BD  
						

							2-3 7. Press the [CAM(SET)] key while turning the Zoom
Wheel to right (TELE) side.
The LCD on the Front Panel will indicate as right.
8. Turn and keep the Zoom Wheel to fully left (WIDE) side.
The LCD on the Front Panel will indicate as right.
9. Press the [CAM(SET)] key while turning the Zoom
Wheel to left (WIDE) side.
The LCD on the Front Panel will indicate as right.
10.  Return the Zoom Wheel to center.
The LCD on the Front Panel will indicate as right.
Note : When the Zoom Wheel is in fully left side,
release the hand as quickly as possible.
11. Press the [CAM(SET)] key.
The LCD on the Front Panel will indicate as right.
12.  Confirm the following.
• The LCD on the Front Panel will indicate 4 steps of
each change, when the Zoom Wheel turns to the WIDE
and TELE sides.
• The value of WIDE and TELE on the LCD will return to
ZERO, when the Zoom Wheel is returned to the center..
13.  Turn off the power to finish the calibration.
T:BD W:__ ZC:__   BD 
T:BD W:__ ZC:__   45 
T:BD W:45 ZC:__   45 
T:BD W:45 ZC:__   81 
T:BD W:45 ZC:81    0
T:BD W:45 ZC:81    0