Panasonic System Controller Wv Cu550c Operating Instructions

Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Model No.WV-CU550C
System Controller
Operating Instructions
ALARM
  ACK
RESET
  AUX
 DEC
-1CAM INC
+1CAM
STOP
S
L
O
W
E
S
C
S
E
T M
O
N
C
A
M
W
ID
E
F
A
R Z
O
O
M
T
E
LEF
O
C
U
S
 N
E
A
R R
E
S
E
TIR
IS
1
2
3
4
5
6
7
8
09
C
L
O
S
E
    O
P
E
N
1            2BACK
 SEQFOWARD
   SEQ
ALT BUSY
LEFT
System Controller WV-CU
550C
RIGHT UP
DOWN F1
F2
F3
F4 

2
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS  ......................................................................................................................................... 3
PREFACE ....................................................................................................................................................................................... 4
FEATURES...

3
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or...

4
PREFACE
The WV-CU550C System Controller, when combined with the optional WJ-SX550C Matrix Switcher and WJ-AD550 Extension
Unit, allows for flexible control of 128 cameras and 16 monitors.
When used in a system with either Receivers (WV-RC100 or WV-RC150) or with Panasonic
’s Combination cameras, the WV-
CU550C can control camera functions such as zoom and focus and can also control accessory equipment such as Pan/Tilt
Heads.
In addition, the WV-CU550C can control sequential switching in systems...

5
PRECAUTIONS
• Refer all work related to the installation of this
product to qualified service personnel or system
installers.
• Do not attempt to disassemble the appliance.
To prevent electric shock, do not remove screws or
covers.
There are no user-serviceable parts inside. Contact
qualified service personnel for maintenance.
• Handle the appliance with care.
Do not strike or shake it, as this may damage the appli-
ance.
• Do not expose the appliance to water or moisture,
nor try to operate it in wet...

6
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Front View
123
456
789
MON CAM
ESC SET0
ACK
RESETBACK
SEQFORWARD
SEQALT
DEC
–1CAMINC
+1CAM STOP
SLOW12AUX
CLOSEOPEN IRISPRESET
FOCUS
NEAR ZOOM
TELE
FAR WIDE
System Controller WV-CU550
LEFT RIGHTUP
DOWN
ALARMBUSY
F3F4F2F1
C
AF
qwert
y
uio!0!1!2!3!4!5!6!7 @1 !9
!8
@0
CONTROLLER
ON OFFINOUTTERMON OFF
DATA
0123456789
CONTROLLER
UNIT NO.
1-8MODE
#1#2#3#4#5#6
Rear View 

7
qAlarm Indicator (ALARM)
Blinks to indicate that an alarm condition exists.
It changes to steady light when the alarm is reset auto-
matically.
To turn the indicator off, press the ACK RESET button.
wBusy Indicator (BUSY)
Lights up when you attempt to control a monitor or a
camera that is already used by a higher priority opera-
tor, or when the higher priority operator selects the
monitor or camera you are currently operating.
Operations from the System Controller are disabled
until this indicator...

8
!7Auxiliary Button (AUX 1,2)
These buttons toggle the auxiliary switches in the
Receiver on and off.
The auxiliary switches can be used, for example, to
activate equipment connected to the receiver, such as
lamps and buzzers.
!8Alternate Button (ALT)
This button activates the alternate function of dual-func-
tion control buttons.
!9Forward Sequence Button (FORWARD SEQ)
This button is used to run a selected Program or Tour
Sequence in forward direction on the active monitor.
It also restarts a sequence...

9
The installation described below should be made by qualified service personnel or system installers and should
conform to all local codes.
Replacing the Side Panels with the optional WV-Q62 Rack Mounting
Brackets
1. Remove both the left and right side panels of the System Controller by removing four screws.
2. Remove the Palm-rest located on the front of the System Controller by removing two screws.
3. Place the Rack Mounting Brackets on both sides of the System Controller and tighten with the four...

10
SYSTEM INFORMATION
Please note that the following functions were added to
improve the operation of the combination cameras.
Additions
 Selection of Pan/Tilt Speed 
The Pan/Tilt speed can be changed by selecting a mode in
the menu (A1) displayed on the LCD display of the con-
troller.
1. Select the desired monitor and camera.
2. Select a mode by pressing the [F3]or [F4]button.
“❑” indicates the currently selected mode.
SLW:Moves the Pan/Tilt Head at lower speed.
FST:  Moves the Pan/Tilt Head at...