Panasonic Studio Card Aw Pb301 Operating Instructions

							-9-
– +MENU
ITEM/AWC
YES/ABC
NO/BAROPTION  CARD
VIDEO  OUT
I/F  REMOTE
G/L IN
IRIS
DC12V IN
MENU Switchiªj
LEVEL
INCOM EVFST.BY
ON
ITEM Switchi«j
NO Switchi|j YES Switchi{j
PAGE
ITEM
UP
DOWN
COARSE
FINE
SC PHASE270¡
180¡ 90¡ 0¡ H.PHASE USER SET
OFF ENC
VF ON
User Set SwitchPAGE Switch
ITEM Switch
UP Switch
DOWN Switch
CAMERA
RCU (RCB) (2) The setting item (flashing) changes each time the
menu switch, item switch, or NO switch is pressed.
Select [Option Card Set] and press the YES switch
to display the [Option Card Set] submenu.
(3) Select an item to set using the menu switch and
item switch.
(4) Change the settings using the YES and NO switch-
es.
(5) Select [Return] with the menu switch and item
switch, and press the YES switch to return to the
main menu.
(6) The camera is now back in shooting condition.
Camera alone:Select [End] with the menu switch
and item switch, then press the YES switch.
With RCU (RCB):Set the user set switch in the
pocket to OFF.
The camera will now operate under the conditions
thus set. 
						

							-10-
**Opation Card Set**
 Zebra Indicator       ON
  Zebra 1 Level       70%
  Zebra 2 Level       85%
 Safety Zone            I
 EVF Output             Y
 Component          R/G/B
Return
**Opation Card Set**
 Zebra Indicator       ON
  Zebra 1 Level       70%
  Zebra 2 Level       85%
 Safety Zone            I
 EVF Output             Y
Return
AW-PB301 AW-PB305
nOption Card Setting SubmenuqZebra Indicator [Zebra Indicator: OFF/ON]
ON:Zebra indicator is shown in the viewfinder.
OFF:Zebra indicator is not shown in the viewfinder.
Note:If [CVBS] is selected at Item [EVF Output:
Y/CVBS] r, the zebra indicator will not be
shown.
wZebra 1 Level Set [Zebra 1 Level: 70% to 109%]
Zebra 2 Level Set [Zebra 2 Level:  71% to 110%]
Zebra level 1 or 2 can be only when Zebra Indicator
qis at ON.The zebra indicator can be shown in two steps
using two zebra patterns.
2 Level shows a finer zebra pattern than 1 level.
2 Level must be set at least 1% higher than 2 level.
eSafety Zone Select [Safety Zone: 1 to 5/OFF]
A type of safety zone to be shown in the viewfinder
can be selected.
No safety zone is shown if OFF is selected. 
						

							-11-
12 3
45The inner frame indicates a safety zone of about
90% and the outer frame, a safety zone of about
95%.
Note:The safety zone and center marker indicate
electrical positions, which may differ from opti-
cal positions.
rViewfinder Output Signal Select [EVF Output:
Y/CVBS]
Y:Luminance signals are output to the viewfinder.
CVBS:Color signals are output to the viewfinder.
No zebra indicator will be shown.tComponent Output Select [Component Output:
R/G/B, Y/Pr/Pb, Y/C] (AW-PB301 only)
Component output signals can be selected.
Component output signals are output from the inter-
face/remote connector on the rear of the camera.
Note:R/G/B output or Y/Pr/Pb output will be posi-
tive in reproduced image regardless of the set-
tings made with [Nega/Posi Set] on the [Other
Settings] submenu of the main menu. 
						

							-12-
APPEARANCE
mm (inch)
LEVEL
INCOM EVFST.BY
ON
70 (2-3/4)
21.5
(27/32)96 (3-3/4)
91 (2-3/4) 5 (3/16) 
						

							-13-
Video output: Y/C: Y: 1.0 V[p-p], C: 0.286 V[p-p]
R/G/B: 0.7 V[p-p] (AW-PB301 only)
Y/Pr/Pb: Y: 1.0 V[p-p], Pr/Pb: 0.7 V[p-p] (AW-PB301 only)
SYNC: 2.0 V[p-p] sync signal (AW-PB301 only)
VF output: 1.0 V[p-p], composite, high impedance
Intercom jack: 3.5 mm in diameter
Switch: Switching on the panel:  EVF ST-BY/ON
Switching on the menu:  Zebra indicator ON/OFF, safety zone switching, EVF output switching,
component output switching (AW-PB301 only)
Adjusting functions: Intercom voice output level adjusted on the panel
Zebra level adjusted using the menu 
Source voltage: 12 VDC (supplied from camera)
Power consumption: 3.8 W (AW-PB301), 0.5 W (AW-PB305)
Operating temperature: –10°C to +45°C (14°F to +113°F)
Operating humidity: 30 % to 90 %
Dimensions: 21.5 (W) x 70 (H) x 96 (D) mm [27/32” x 2-3/4” x 3-3/4”]
Weight: 105 g
Weight and dimensions indicated are approximate.
Specifications are subject to change without notice.SPECIFICATIONSIntercom plug adapter
(6.35 mm to 3.5 mm in diameter)  ........................... 1 pcSTANDARD ACCESSORIES
Screw (6 mm long) ................................................ 2 pcs
Screw (8 mm long) ................................................ 4 pcs 
						

							N1098-0 7J1A215A Printed in Japan
Broadcast & Television Systems Company
Division of Matsushita Electric Corporation of AmericaExecutive Office: One Panasonic Way 3F-5, Secaucus, NJ 07094
Regional Offices:
EASTERN ZONE: 50 Meadowlands Parkway, Secaucus, NJ 07094 (201) 348-7620
CENTRAL ZONE: 1707 North Randall Road, Elgin, IL 60123 (847) 468-5200
SOUTHERN ZONE:
    Atlanta Region: 1225 Northbrook Parkway, Suite 1-160, Suwanee, GA 30024
       Panazip 11 (770) 338-6841, fax (770) 338-6741
    Law Enforcement Video Products: 1225 Northbrook Parkway, Suite 1-160, Suwanee,
       GA 30024, Panazip 11 (770) 338-6844, fax (770) 338-6721
WESTERN ZONE:
   Seattle Region: 1200 Westlake Ave. North, Suite 508, Seattle, WA98109 (206) 285-8883
   Los Angeles Region: 6550 Katella Ave. 17A-1, Cypress, CA 90630 (714) 373-7271
   Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
PANASONIC CANADA INC.
5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905) 624-5010
PANASONIC SALES COMPANY
DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO, INC.
San Gabriel Industrial Park, 65th Infantry Ave. KM. 9.5 Carolina, Puerto Rico 00630 (809) 750-4300