Panasonic Sdr Sw21 Operating Instructions Manual

							10VQT2A1711VQT2A17
Quick guide
2Open the card/battery 
door.
Lift the flap upright and turn it 
counter-clockwise until it clicks for 
unlocking and then open the door.
3Insert the battery.
4Close the card/battery 
door.
Close the door and turn the flap 
clockwise to the locking position and 
then push the flap back flat.
1Set the mode dial to 
[OFF].
5Connect the AC adaptor 
(supplied).
To AC outletAC cable
6Open the terminal cover.
7Plug the DC plug into the 
DC input terminal on the 
unit.
1Set the mode dial to 
a position other than 
[OFF].
2Select [YES].
3Set the date and time.
To select settingsTo change 
numerical values
4Enter the date and time.
This procedure is for setting the 
date and time the very first time. For 
the setting procedure for the second 
and subsequent times (P.30).
•
Status indicator
Flashing red:  Charging in 
progress
Off: Charging complete
ChargingSetting the date and time
Press until hearing lever lock. Lever
Inserting SD cards 
(sold separately)
Place label upwards.
Slide straight in until hearing card catch.
Lift the flap upright and turn it 
counter-clockwise until it clicks for 
unlocking and then open the cover.
Small gap here.
AC adaptor 
						

							12VQT2A1713VQT2A17
Quick guide (cont.)
1Set to [].
2
Start recording.
3Stop recording.
1Set to [].
2
Take picture.
 Motion pictures Still pictures
1Set to [].
2
Select and enter the 
picture to view.
Slideshow start/pauseReturn to step 
2Next
Back
 Motion pictures Still pictures
Playback
Deleting pictures
Recording
1Set to [].
2
Select and enter the 
picture to view.
Play/Pause
Return to step 
2 Next
Back
1
During playback
(LCD monitor display in 
motion picture viewing)
2
Select [YES].
   The display and menu 
language can be changed
  →[LANGUAGE] 
						

							12VQT2A1713VQT2A17
Quick guide (cont.)
1Set to [].
2
Start recording.
3Stop recording.
1Set to [].
2
Take picture.
 Motion pictures Still pictures
1Set to [].
2
Select and enter the 
picture to view.
Slideshow start/pauseReturn to step 
2Next
Back
 Motion pictures Still pictures
Playback
Deleting pictures
Recording
1Set to [].
2
Select and enter the 
picture to view.
Play/Pause
Return to step 
2 Next
Back
1
During playback
(LCD monitor display in 
motion picture viewing)
2
Select [YES].
   The display and menu 
language can be changed
  →[LANGUAGE] 
						

							14VQT2A1715VQT2A17
Accessories
Make sure all of the following 
accessories were included in the 
product package.
(Accessories except for the hand 
strap are not waterproof.)Battery pack
VW-VBJ10
The battery is shipped 
in a discharged state. 
Be sure to charge the 
battery before using 
this unit (P.22).
•
AC adaptor
VSK0694
•
AC cableK2CA2CA00025•
AV cable
K2KZ9CB00002
•
Hand strap
VFC4409
•
Float
USB cable
K1HA05AD0005
•
Brush
VYC0998
•
CD-ROM
LSFT0771
•
LCD monitor (P.16)
Underwater button 
[UNDERWATER] (P.51)
Speaker
When recording:  Zoom button
 [T/W] (P.38)
During playback:  Volume button  [+VOL–] (P.56)
Mode dial (P.26): Motion  picture recording (P.34)
: Motion  picture playback (P.56)
: Still picture recording (P.36)
: Still picture playback (P.59)
: Power OFF (P.26)Status indicator 
(P.23, 26, 27)
Record button
(P.34, 36)
Strap fixture (P.16)
Menu button [MENU] (P.28)
Cursor buttons (P.29)
Delete button 
[
] (P.60)
Manual button
[MANUAL AF/MF] (P.48) Sub record button (P.32)
(Same as record button)
Lens
Microphone 
(built-in, stereo) White balance sensor 
(P.32)
Audio-video output 
terminal [A/V] (P.64, 65)
USB terminal 
[
] (P.66, 69, 80)
DC input terminal 
[DC IN 5.0 V] (P.23)
Battery slot 
[BATT] (P.22) Card slot
 [SD CARD] 
(P.25)
Card access lamp 
[ACCESS] (P.25, 33)
Card/Battery door lock 
(P.17, 22, 25)
Card/Battery door 
(P.17, 22, 25)
Tripod mounting holeFor tripod (sold separately) mounting 
instructions, see the user’s guide for 
the tripod. (With some tripods, the 
card/battery door cannot be opened 
when the unit is mounted on the tripod. 
If this is the case, insert the SD card 
and battery before mounting the unit 
on the tripod.)
Parts identification 
Auto button 
[AUTO] (P.34)
•  
Do not use any other AC adaptors 
except the supplied one.
Drain port (P.19) Terminal cover lock 
(P.17, 23)
Terminal cover 
(P.17, 23)
and handling
WEB Mode button [WEB MODE] (P.40) 
						

							14VQT2A1715VQT2A17
Accessories
Make sure all of the following 
accessories were included in the 
product package.
(Accessories except for the hand 
strap are not waterproof.)Battery pack
VW-VBJ10
The battery is shipped 
in a discharged state. 
Be sure to charge the 
battery before using 
this unit (P.22).
•
AC adaptor
VSK0694
•
AC cableK2CA2CA00025•
AV cable
K2KZ9CB00002
•
Hand strap
VFC4409
•
Float
USB cable
K1HA05AD0005
•
Brush
VYC0998
•
CD-ROM
LSFT0771
•
LCD monitor (P.16)
Underwater button 
[UNDERWATER] (P.51)
Speaker
When recording:  Zoom button
 [T/W] (P.38)
During playback:  Volume button  [+VOL–] (P.56)
Mode dial (P.26): Motion  picture recording (P.34)
: Motion  picture playback (P.56)
: Still picture recording (P.36)
: Still picture playback (P.59)
: Power OFF (P.26)Status indicator 
(P.23, 26, 27)
Record button
(P.34, 36)
Strap fixture (P.16)
Menu button [MENU] (P.28)
Cursor buttons (P.29)
Delete button 
[
] (P.60)
Manual button
[MANUAL AF/MF] (P.48) Sub record button (P.32)
(Same as record button)
Lens
Microphone 
(built-in, stereo) White balance sensor 
(P.32)
Audio-video output 
terminal [A/V] (P.64, 65)
USB terminal 
[
] (P.66, 69, 80)
DC input terminal 
[DC IN 5.0 V] (P.23)
Battery slot 
[BATT] (P.22) Card slot
 [SD CARD] 
(P.25)
Card access lamp 
[ACCESS] (P.25, 33)
Card/Battery door lock 
(P.17, 22, 25)
Card/Battery door 
(P.17, 22, 25)
Tripod mounting holeFor tripod (sold separately) mounting 
instructions, see the user’s guide for 
the tripod. (With some tripods, the 
card/battery door cannot be opened 
when the unit is mounted on the tripod. 
If this is the case, insert the SD card 
and battery before mounting the unit 
on the tripod.)
Parts identification 
Auto button 
[AUTO] (P.34)
•  
Do not use any other AC adaptors 
except the supplied one.
Drain port (P.19) Terminal cover lock 
(P.17, 23)
Terminal cover 
(P.17, 23)
and handling
WEB Mode button [WEB MODE] (P.40) 
						

							16VQT2A1717VQT2A17
Using the hand strap (supplied)
 Using as strap
  Fit over your wrist and adjust the 
length of the strap.
 Using as a grip belt
  Screw the adaptor hanging from 
the strap into the tripod hole.  Fit over your hand and adjust the 
length of the strap.
 Attaching the floatThe float prevents the unit from sinking 
when it is accidentally dropped into water.
Cleaning the float after use (P.19)
●
Attach the float here.
Using the LCD monitor
Images can be checked on the LCD monitor when recording.
 Open the LCD monitor. Adjust the angle.
Hold [] to 
open.
Up to 90 ˚
Up to 90 ˚
Opening the LCD monitor beyond the mechanical limit or turning it more t\
han 
90 ˚ may allow water to enter and damage the mechanism.
Brightness and color density can be adjusted. (P.31)
●
●
Parts identification and handling (cont.)
“Before using the unit under water”
(IMPORTANT) Waterproof performance
Waterproof performance
The waterproofing and dustproofing of this unit comply with IP58 of IEC \
60529 “Degrees 
of protection provided by enclosures (IP Code)”. The unit passed waterproofing tests 
(IEC 60529), in which it was submerged to a depth of 2.0 m (6.5 feet)\
 for 30 minutes, 
and dustproof tests (IP Code: IP58) in accordance with Panasonic standards, but this 
does not guarantee that the unit will not be damaged or malfunction by c\
ontact with 
water and dust. (The supplied AC adaptor and battery are not waterproof.)
This unit can be used underwater, but care should be taken as improper 
handling may cause water to enter the unit and result in malfunction and\
 
loss of SD card data. Read the following carefully before using the unit\
.
The penetration of water into the unit due to mishandling by the user is\
 not covered by 
the guarantee given for the unit’s waterproof performance. If water should penetrate 
the unit, stop using the unit, and consult the dealer from whom you purc\
hased the unit.
 HandlingDo not leave the unit in locations where the 
temperature exceeds 40 °C (104 °F) (such as 
places exposed to strong sunlight, car interiors 
on hot days or locations near heating equipment, 
in particular) for extended periods of time. (Doing 
so could degrade its waterproof performance.)
The waterproof performance of the unit cannot 
be guaranteed if it is exposed to impacts, such 
as being bumped or dropped. If the unit is 
deformed by an impact, refrain from using it underwater and contact Serv\
ice 
Center to have its waterproof performance checked (charges apply).
Do not plug the unit in or unplug it with wet hands.
The unit’s waterproof performance is effective only in fresh and saltwater.
 Opening and closing the card/battery door and terminal coverTo open:  Lift the flap upright and turn it counter-clockwise until it clicks for \
unlocking and then open the door/cover.
 To close:   Close the door/cover and turn the flap clockwise to the locking 
position and then push the flap back flat.
Locking 
position
Do not open and close the card/battery door and terminal cover with wet \
hands or when in or near water.
When droplets of water have formed on this unit or on the inside of its \
doors 
or cover, be absolutely sure to wipe them off using a lint-free cloth before 
opening or closing the parts concerned.
•
•
•
•
•
•
•
NG
NG
Over 40 °C  (104 °F) 
						

							16VQT2A1717VQT2A17
Using the hand strap (supplied)
 Using as strap
  Fit over your wrist and adjust the 
length of the strap.
 Using as a grip belt
  Screw the adaptor hanging from 
the strap into the tripod hole.  Fit over your hand and adjust the 
length of the strap.
 Attaching the floatThe float prevents the unit from sinking 
when it is accidentally dropped into water.
Cleaning the float after use (P.19)
●
Attach the float here.
Using the LCD monitor
Images can be checked on the LCD monitor when recording.
 Open the LCD monitor. Adjust the angle.
Hold [] to 
open.
Up to 90 ˚
Up to 90 ˚
Opening the LCD monitor beyond the mechanical limit or turning it more t\
han 
90 ˚ may allow water to enter and damage the mechanism.
Brightness and color density can be adjusted. (P.31)
●
●
Parts identification and handling (cont.)
“Before using the unit under water”
(IMPORTANT) Waterproof performance
Waterproof performance
The waterproofing and dustproofing of this unit comply with IP58 of IEC \
60529 “Degrees 
of protection provided by enclosures (IP Code)”. The unit passed waterproofing tests 
(IEC 60529), in which it was submerged to a depth of 2.0 m (6.5 feet)\
 for 30 minutes, 
and dustproof tests (IP Code: IP58) in accordance with Panasonic standards, but this 
does not guarantee that the unit will not be damaged or malfunction by c\
ontact with 
water and dust. (The supplied AC adaptor and battery are not waterproof.)
This unit can be used underwater, but care should be taken as improper 
handling may cause water to enter the unit and result in malfunction and\
 
loss of SD card data. Read the following carefully before using the unit\
.
The penetration of water into the unit due to mishandling by the user is\
 not covered by 
the guarantee given for the unit’s waterproof performance. If water should penetrate 
the unit, stop using the unit, and consult the dealer from whom you purc\
hased the unit.
 HandlingDo not leave the unit in locations where the 
temperature exceeds 40 °C (104 °F) (such as 
places exposed to strong sunlight, car interiors 
on hot days or locations near heating equipment, 
in particular) for extended periods of time. (Doing 
so could degrade its waterproof performance.)
The waterproof performance of the unit cannot 
be guaranteed if it is exposed to impacts, such 
as being bumped or dropped. If the unit is 
deformed by an impact, refrain from using it underwater and contact Serv\
ice 
Center to have its waterproof performance checked (charges apply).
Do not plug the unit in or unplug it with wet hands.
The unit’s waterproof performance is effective only in fresh and saltwater.
 Opening and closing the card/battery door and terminal coverTo open:  Lift the flap upright and turn it counter-clockwise until it clicks for \
unlocking and then open the door/cover.
 To close:   Close the door/cover and turn the flap clockwise to the locking 
position and then push the flap back flat.
Locking 
position
Do not open and close the card/battery door and terminal cover with wet \
hands or when in or near water.
When droplets of water have formed on this unit or on the inside of its \
doors 
or cover, be absolutely sure to wipe them off using a lint-free cloth before 
opening or closing the parts concerned.
•
•
•
•
•
•
•
NG
NG
Over 40 °C  (104 °F) 
						

							18VQT2A1719VQT2A17
“Before using the unit under water”
(IMPORTANT) Waterproof performance (cont.)
  Check the following before closing the card/battery door and 
terminal cover.
If foreign material (such as a strand of hair or string, or some sand o\
r dust) 
adheres to the areas shown in black in the illustration ( rubber packings and  areas they come in contact with) when the card/battery door or termina\
l 
cover is closed, water could leak inside and cause a malfunction when th\
e unit 
is used underwater. Check to make sure no foreign matter has adhered to the 
areas indicated before closing the card/battery door and terminal cover.
If you notice any cracks or malformations in the areas shown in black in\
 the 
illustration, contact Service Center to have the affected parts replaced.
Brush
NG
Strands of hair or 
thread Sand or dustCracks or 
malformations
Remove any minute objects with the supplied brush.
   Underwater useThe unit may be used underwater at depths not exceeding 
2.0 m (6.5 feet), and in areas where the water temperature 
is in the range of 0 °C to 40 °C (32 °F to 104 °F); do not\
, 
however, use it continuously underwater for more than 
30 minutes. Before using the unit again underwater, wipe 
off the moisture using a lint-free cloth, and allow the unit to 
dry thoroughly in a well-ventilated location.
Do not jump or dive into the water while holding the unit 
or subject the unit to impacts while in the water. (Doing so 
may cause water to leak inside.) Do not use the unit where 
the current is swift, near waterfalls, or in other locations 
where it will be subjected to the strong forces exerted by 
water. (Doing so may cause high water-pressure to be 
applied to the unit, possibly resulting in problems.)
Since the unit will sink in water, attach the float 
provided to the strap and fix the strap securely in place 
or take other steps to ensure that it will not be dropped.
Do not use the unit in hot water (such as in a bathtub or 
hot springs) with a temperature exceeding 40 °C (104 °F).
Do not use the unit underwater while the tripod 
(sold separately) or any type of camera base is still 
mounted in the unit’s tripod mounting hole. Doing 
so may cause water to seep inside, possibly causing the unit to malfunct\
ion.
•
•
•
•
•
•
•
  
Care after underwater useAfter using the unit underwater, do not leave it standing 
for more than 60 minutes without being absolutely 
sure to immerse it in fresh water. (Otherwise, the unit’s 
waterproof performance may be compromised.)
Wipe off any dirt or water droplets on the unit 
using a lint-free cloth.
After using the unit at the beach or underwater, move 
it back and forth in a shallow container of fresh water 
while opening and closing the LCD monitor to rinse 
the unit off. Leave the unit immersed for up to 30 
minutes, and then wipe it dry using a lint-free cloth.
Even when the unit is rinsed in water, salt particles 
may still be found on the insides of the flaps. Lift 
the flap upright, rinse the inside with running tap 
water, and then wipe the flap dry using a lint-free cloth.
To clean the float, rinse it off in fresh water, and then wipe off the remaining 
moisture using a dry towel. Do not use bleach.
Do not blow hot air onto the unit using, for instance, a hair drier in o\
rder to 
dry it out. Do not use benzine, thinner, alcohol or other chemicals, soap or 
kitchen detergents. Doing so may result in deformation or deterioration \
that 
may in turn compromise the unit’s waterproof performance.
If the unit is splashed or sprayed with detergent, soap, water from a ho\
t 
spring, bath salts, suntan oil, sun screen lotion or chemicals, wipe off the 
droplets immediately.
After rinsing off the unit, leave it to dry thoroughly in a well-ventilated, shady 
location with its water drain holes facing down. If the inside of the un\
it is not 
dry, water may emerge from the water drain holes.
  Microphone and speakerIf water droplets have formed on the microphone and speaker, the volume of 
the sound may be reduced or the sound itself may become distorted. Wipe \
off the droplets and leave the unit to dry thoroughly before using it agai\
n.
Do not insert sharp or pointed objects into the holes of the microphone \
and speaker. (Doing so may damage the water-proofing sheet inside and 
compromise the unit’s waterproof performance.)
  Inspecting the units waterproof performanceIn order to maintain the units waterproof performance, it is recommende\
d that this 
performance be checked about once every 3 years after the unit is purcha\
sed.
It is also recommended that this performance be checked whenever the uni\
t 
has been subjected to a strong shock such as when it has been dropped.
When it is time to check the waterproof performance, please consult with\
 a 
service center representative.
Users will be charged for having the waterproof performance of their uni\
ts 
inspected and for having the waterproof packing in their units replaced.\
•
•
•
•
•
•
•
•
•
•
•
•
2.0 m (6.5 feet)Not more than 
30 minutes
NG
0 °C(32 °F)40 °C(104 °F)
NG
Not more than 60 minutes 
						

							18VQT2A1719VQT2A17
“Before using the unit under water”
(IMPORTANT) Waterproof performance (cont.)
  Check the following before closing the card/battery door and 
terminal cover.
If foreign material (such as a strand of hair or string, or some sand o\
r dust) 
adheres to the areas shown in black in the illustration ( rubber packings and  areas they come in contact with) when the card/battery door or termina\
l 
cover is closed, water could leak inside and cause a malfunction when th\
e unit 
is used underwater. Check to make sure no foreign matter has adhered to the 
areas indicated before closing the card/battery door and terminal cover.
If you notice any cracks or malformations in the areas shown in black in\
 the 
illustration, contact Service Center to have the affected parts replaced.
Brush
NG
Strands of hair or 
thread Sand or dustCracks or 
malformations
Remove any minute objects with the supplied brush.
   Underwater useThe unit may be used underwater at depths not exceeding 
2.0 m (6.5 feet), and in areas where the water temperature 
is in the range of 0 °C to 40 °C (32 °F to 104 °F); do not\
, 
however, use it continuously underwater for more than 
30 minutes. Before using the unit again underwater, wipe 
off the moisture using a lint-free cloth, and allow the unit to 
dry thoroughly in a well-ventilated location.
Do not jump or dive into the water while holding the unit 
or subject the unit to impacts while in the water. (Doing so 
may cause water to leak inside.) Do not use the unit where 
the current is swift, near waterfalls, or in other locations 
where it will be subjected to the strong forces exerted by 
water. (Doing so may cause high water-pressure to be 
applied to the unit, possibly resulting in problems.)
Since the unit will sink in water, attach the float 
provided to the strap and fix the strap securely in place 
or take other steps to ensure that it will not be dropped.
Do not use the unit in hot water (such as in a bathtub or 
hot springs) with a temperature exceeding 40 °C (104 °F).
Do not use the unit underwater while the tripod 
(sold separately) or any type of camera base is still 
mounted in the unit’s tripod mounting hole. Doing 
so may cause water to seep inside, possibly causing the unit to malfunct\
ion.
•
•
•
•
•
•
•
  
Care after underwater useAfter using the unit underwater, do not leave it standing 
for more than 60 minutes without being absolutely 
sure to immerse it in fresh water. (Otherwise, the unit’s 
waterproof performance may be compromised.)
Wipe off any dirt or water droplets on the unit 
using a lint-free cloth.
After using the unit at the beach or underwater, move 
it back and forth in a shallow container of fresh water 
while opening and closing the LCD monitor to rinse 
the unit off. Leave the unit immersed for up to 30 
minutes, and then wipe it dry using a lint-free cloth.
Even when the unit is rinsed in water, salt particles 
may still be found on the insides of the flaps. Lift 
the flap upright, rinse the inside with running tap 
water, and then wipe the flap dry using a lint-free cloth.
To clean the float, rinse it off in fresh water, and then wipe off the remaining 
moisture using a dry towel. Do not use bleach.
Do not blow hot air onto the unit using, for instance, a hair drier in o\
rder to 
dry it out. Do not use benzine, thinner, alcohol or other chemicals, soap or 
kitchen detergents. Doing so may result in deformation or deterioration \
that 
may in turn compromise the unit’s waterproof performance.
If the unit is splashed or sprayed with detergent, soap, water from a ho\
t 
spring, bath salts, suntan oil, sun screen lotion or chemicals, wipe off the 
droplets immediately.
After rinsing off the unit, leave it to dry thoroughly in a well-ventilated, shady 
location with its water drain holes facing down. If the inside of the un\
it is not 
dry, water may emerge from the water drain holes.
  Microphone and speakerIf water droplets have formed on the microphone and speaker, the volume of 
the sound may be reduced or the sound itself may become distorted. Wipe \
off the droplets and leave the unit to dry thoroughly before using it agai\
n.
Do not insert sharp or pointed objects into the holes of the microphone \
and speaker. (Doing so may damage the water-proofing sheet inside and 
compromise the unit’s waterproof performance.)
  Inspecting the units waterproof performanceIn order to maintain the units waterproof performance, it is recommende\
d that this 
performance be checked about once every 3 years after the unit is purcha\
sed.
It is also recommended that this performance be checked whenever the uni\
t 
has been subjected to a strong shock such as when it has been dropped.
When it is time to check the waterproof performance, please consult with\
 a 
service center representative.
Users will be charged for having the waterproof performance of their uni\
ts 
inspected and for having the waterproof packing in their units replaced.\
•
•
•
•
•
•
•
•
•
•
•
•
2.0 m (6.5 feet)Not more than 
30 minutes
NG
0 °C(32 °F)40 °C(104 °F)
NG
Not more than 60 minutes 
						

							20VQT2A1721VQT2A17
The following SD and SDHC Memory Cards can be used.
Type of cardCapacity
SD Memory Card
(SD speed Class 2 or higher recommended) 256 MB
512 MB
1 GB
2 GB
SDHC Memory Card
(Use cards bearing the 
 logo.) 4 GB
6 GB
8 GB
12 GB
16 GB
32 GB
8 MB and 16 MB SD Memory Cards are for still picture recording only.
With 32 MB, 64 MB and 128 MB SD Memory Cards, still pictures can be 
recorded, but motion picture recording may stop during use. 
Multimedia cards cannot be used.
•
•
•
  
Recommended Panasonic SD/SDHC Memory Cards 
(as of January 2009)
The following Panasonic SD/SDHC Memory Cards and SD speed Class 2 or 
higher Memory Cards are recommended for this unit. With other types of S\
D 
cards, motion picture recording may stop during use.
SD Memory Card SD/SDHC Memory Card
High Speed Class 2 Class 4 Class 6
256 MB RP-SDH256 RP-SDR256 ――
512 MB RP-SDK512 RP-SDR512 ――
1 GB RP-SDH01G RP-SDR01G ―RP-SDV01G
2 GB RP-SDK02G RP-SDR02G RP-SDM02G RP-SDV02G
4 GB ―RP-SDR04G RP-SDM04G RP-SDV04G
6 GB ―― RP-SDM06G―
8 GB ――― RP-SDV08G
12 GB ―― RP-SDM12G―
16 GB ――― RP-SDV16G
32 GB ――― RP-SDV32G
SDHC Memory Cards can be used only with SDHC devices.
Be careful when sharing cards between devices.
Be sure to format SD cards with this unit only.
If cards are formatted on a PC or other device, recording may take time \
and 
the card may become unusable with the unit. 
Before using an SD card from another device, copy the data onto a PC or \
other storage device and then format the card with this unit.
Keep the Memory Card out of reach of children to prevent swallowing.
This unit supports SD Memory Cards formatted to FAT12 or FAT16 file 
systems and SDHC Memory Cards formatted to a FAT32 file system. 
SD speed Class 2    
Class 2 speed standard for SD cards. This and higher types of SD cards 
operate stably in devices for which Class 2 or higher SD cards are 
recommended, such as this unit.
●
●
●
●
●
●
Precautions in handlingDo not touch the terminals on the back of the card. Also, prevent dirt, water 
and foreign matter from adhering to terminals.
Do not leave cards in the following areas:
· Where exposed to direct sunlight
· Humid or dusty places
· Near heaters or other sources of heat
·  Where subjected to sharp temperature changes (condensation can occur)
· Where exposed to static electricity or electromagnetic waves
After use, return cards to their pouch or case.
SD card data may be corrupted or lost due to electrical noise, static 
electricity, damage to the unit or card, etc. Save important data on a PC 
using the supplied USB cable, VideoCam Suite, etc. (P.74)
•
•
•
•
Applicable SD cards (sold separately)
 Write-protecting  cardsWhen the write-protect switch on the SD card is set to the LOCK position\
, 
data cannot be written onto or deleted from the card, and the card canno\
t be 
formatted.
Write-protect switch