Panasonic SD Media Storage Sv Pt1 Operating Instructions

							11
Before Use
Before Using
Copying and Backup
Copying: Memory Card -> PC Card HDD
When copying from a Memory Card to the PC Card HDD, create a folder entitled
“CARD****” for each copy and save Memory Card data into this folder. When BACKUP
is ON, the “CARD****” folder mentioned above is created in the “BACKUP” folder of
the PC Card HDD, and Memory Card data is copied into this folder. Thus, normal PC
Card HDD available space is reduced by half. See page 20 on how to turn the
BACKUP function ON and OFF.
See next page on how to copy from PC Card HDD to a Memory Card.
The contents of the BACKUP folder cannot be checked during TV mode. Use the computer to
check the contents at this time.
Secure data files (audio files that include copyright restrictions) will not be copied.
The **** por tion of the “CARD****” folder name is assigned automatically in numerical order
within the range of “A001~A999, B001~Z999”. Because of this, please do not change the
file names yourself.– Note –
Memory CardPC Card HDD
ROOT
MISC
DCIM
ROOT
PHOTO
ROOT
MISC
DCIM
AAA. JPG
BBB. TXT
CCC. EXE 1
2
3
ROOT
MISC
DCIM CARDA001
CARDA002
PHOTO
CARDA003
MISC
DCIM
AAA. JPG
BBB. TXT
CCC. EXE
BACKUP
CARDA001
CARDA002
CARDA003Delete
* Even after deletion,
the data will be
retained in the
[BACKUP] folder.
PT1.p10-13.p652003/01/14, 12:36 11 
						

							12
Copying: PC Card HDD -> Memory Card
The folder entitled “CARD****” will disappear and data will be copied according to the file
structure rules.
Before Using
Memory CardPC Card HDD
ROOT
MISC
DCIM
ROOT
PHOTO
ROOT
MISC
DCIM
AAA. JPG
BBB. TXT
CCC. EXE ROOT
MISC
DCIM CARDA001
CARDA002
PHOTO
CARDA003
MISC
DCIM
AAA. JPG
BBB. TXT
CCC. EXE
BACKUP
CARDA001
CARDA002
CARDA003
Data files will not
be copied.
BACKUP folder contents,
not displayable in TV mode,
can be copied/edited/
deleted on a computer.
Secure data files (including
copyrighted audio files) will
not be copied.
When copying data to a
Memory Card, reset the
DPOF settings on devices,
such as digital cameras,
digital video cameras, etc.
that allow you to do so. See
the device manual.
If no MISC folder has been
created on the card to
which the data will be
copied, the MISC folder will
also be copied.
When copying a DCIM
folder name, e.g.
“100_PANA”, and that
name already exists on the
card, change the name to
“101_PANA” before
copying.
If an overwrite operation is
about to occur in a folder
other than the DCIM folder,
a message asking the user
to confirm the overwrite
operation will be displayed.
Copying: Memory Card  PC Card
When copying from a PC Card to a Memory Card or vice
versa, the data can be copied directly.
This operation is possible for all types of cards
except the PC Card HDD.
– Note –
Memory Card
ROOT
MISC
DCIM
PC Card
ROOT
MISC
DCIM
Copying and Backup (Continued)
PT1.p10-13.p652003/01/14, 12:36 12 
						

							13
Before Use
Selecting Modes
Copy Mode (pp. 19~23)
Copy mode is used to copy data from the inserted card to another card. In addition,
you can press MENU to carry out operations such as checking the card storage
capacity, making backup and TV format settings and formatting cards.
Memory Card PC Card HDD
(Or other card)
TV Mode (pp. 24~41)
In TV mode, you can connect the unit to a TV and then carry out playback and edit
operations (such as copying, deleting, protecting, zooming, rotating and enhancing
colors) for the data stored on a card while viewing the data on a TV screen.
* Only JPG, TIF, and MOV type files can be displayed. Other files require the unit to
be in PC Mode.
or
PC Mode (pp. 42~49)
In PC mode, the unit is connected to a computer using a supplied USB cable,
allowing the unit to function as an external disk drive. The data on the card inside the
unit can then be edited (copied and deleted, etc.), and the accessory software
application can be used to create files for presentations.
or
TV
USB Cable
Video Cable
Memory Card PC Card HDD
(Or other card)
Memory Card PC Card HDD
(Or other card)
PC
PT1.p10-13.p652003/01/14, 12:36 13 
						

							14
Index Of Controls
Front View
SD
HDD
USB
S/V OUT   DC IN
COPY   TV
MODE
BATTERY OPEN
OFF   ON
HDD SAFETY
Hand Strap
Attachment Pin
Attach hand strap here.
(p. 15)
POWER LampLights when power is
ON. Flashes during
battery recharge.
SD LampLights when SD Memory
Card or MultiMediaCard
is accessed.
HDD LampLights when PC Card
HDD or PC Card is
accessed.
CANCEL ButtonCancels Slide Show and
presentations.
Liquid Crystal DisplayThe LCD indicates the current operating (TV, Copy) mode.
In Copy mode, displays battery level, data transfer progress,
and various menus. (pp. 18~23)
With USB cable connection, displays card selection options.
(p. 44)
Left Side View
HDD SAFETY
(ON/OFF)
Switch
Turns HDD
SAFETY function
ON/OFF. (p. 18)
COPY/TV
MODE Switch
Switches between
Copy and TV
operating mode.
(pp. 19, 24)
Battery
Compartment
Holds the battery.
End View
USB TerminalBy connecting this unit to a
PC with the supplied USB
cable, it can function as an
external drive. (pp. 42~49)S/V Output ConnectorYou can use the supplied
video cable to connect this
unit to the S-Video or Video
terminals of a TV to view
images. (p. 24)
DC Input Connector
(Power Supply)
This unit can be supplied
with external power by
connecting the AC adaptor
(supplied) to this connector.
(pp. 16, 24, 42)
HDD SAFETY Detection
Switch
This switch pops out if the unit is
lifted up. In this case, the HDD
and all operations stop.
(p. 18)
Cursor Buttons
(            )
Moves the cursor up,
down, left and right.
MENU ButtonDisplays/Clears menu.
SD Memory Card
Slot
Open to insert/remove SD
Memory Card or
MultiMediaCard.  (p. 17)
STANDBY ButtonPress this button for
approx. 2 seconds to turn
power ON/OFF.
SET ButtonExecutes selected
operation.
PC Card HDD (PC
Card) Slot
Slide lever and open
cover to inser t/remove
PC Card HDD or PC
Card. (p. 17)
RESET FunctionPress CANCEL and
STANDBY simultaneously
for 5 seconds to reset unit.
(p. 52)
Connector CoverProtects the
connectors.
PT1.p14-18.p652003/01/14, 12:36 14 
						

							15
Before Use
Carrying the Unit
1Insert strap end loop into gap of
Attachment Pin.
2Thread opposite end through the
end loop and pull strap tight in
the direction of arrow.
This unit is a precision device. When carrying this unit, ensure that it does not swing
excessively. Do not drop this unit or subject it to strong impacts.
1Open the carrying case.
2Insert this unit into the lower
compar tment.
3Insert the PC Card HDD case into
the upper compar tment with the
“PC Card HDD” mark facing
upward.
4Close the carrying case.
When transporting the unit, always turn off the power and insert the PC Card HDD into its
case and then place the case inside the carrying case.
Attaching the Hand Strap
Using the Carrying Case
Caution
Caution
PT1.p14-18.p652003/01/14, 12:36 15 
						

							16
Recharging the Battery Pack
The batter y pack can be recharged right inside this unit using the supplied AC
adaptor. Unit power must be turned OFF before recharging. Charging will stop if
unit power is turned on.
1Slide the battery
cover slightly to the
right and swing open.
2Insert the battery
(labeled side up) all the
way into the battery
compartment.
3Close the cover.
4Connect the DC plug
of the AC adaptor to
unit’s DC IN terminal,
then the AC adaptor
into a wall outlet.
The POWER Lamp
flashes during
recharging.
5Recharge is complete when POWER Lamp
goes out.
A fully charged battery, given a temperature of 20 °C with
60 % humidity, will give about 80 minutes of operating time.
(Operating time may depend on the conditions of usage.)
To remove the Battery :
Use your finger tip to push
down on the catch.
1
2
12
Remove battery if unit will not
be used for a long period.
Do not install/remove batter y
or plug in or unplug the AC
adaptor with unit power ON.
This may cause unit damage
or loss of data.
Do not unplug AC adaptor
while recharging.
POWER Lamp Indications During ChargingDuring normal charging, the POWER Lamp flashes in approx. 1-second intervals. Charging usually
finishes in about 90 minutes. However, if the lamp flashes faster or slower than this (or if POWER
Lamp goes out before charging is finished), it means a problem has occurred. The flashing speed
can tell you what the problem may be. See below.
If you believe a problem has occurred, contact your nearest Servicenter.
Flashing rapidly (approx. 0.5-second intervals):
Possible problem with the unit or battery or the AC adaptor.
Flashing slowly (approx. 6 second intervals):
Temperature of the battery or its surroundings is too high or low, or the battery is over-
discharging. Charging can still continue under these conditions, but will take longer than
normal.
Lamp is OFF (charging is not yet finished):
There may be a problem with the AC adaptor.
Catch
Caution
PT1.p14-18.p652003/01/14, 12:36 16 
						

							17
Before Use
Inserting the Card
SD Memory Card Slot
1Push up slightly on card
door to swing open.
2Insert the Memory Card
(labeled side up, cropped
corner right) and hold in
place until you hear a click.
3Close the lid.
To remove Card :
Open card door.
Press in lightly on
card then release.
cropped corner
PC Card Slot
1Slide the lever to open the
cover.
2Insert the PC Card HDD or
PC Card all the way into
the slot.
3Close the cover.
To remove Card :
Press EJECT TAB
twice.
Always insert card in the correct direction. Failure to do so may result in damage to the card
and this unit.
The PC Card HDD and Memory Card are precision devices. Do not subject them to excessive
pressure or strong impacts.
If the card door does not close completely, remove the card, check insertion orientation, and
reinser t. Also, confirm that EJECT TAB was firmly pressed.
Set STANDBY to OFF when inserting or removing a Card.
2
1
Caution
PT1.p14-18.p652003/01/14, 12:36 17 
						

							18
Turning the Power On
1Insert the battery and connect the AC adaptor. (p. 16)The unit can be operated using only the batter y, but when using PC mode, the AC
adaptor must be connected, otherwise the unit will not turn on.
2Place unit on a flat, level surface.If this is not done, the HDD SAFETY Switch may prevent the unit from operating.
(See below.)
3Press STANDBY for approx. 2 seconds.The power comes on (POWER Lamp lights) and the
unit cycles through each operating mode in sequence.
(p. 13)To turn this unit off :Press STANDBY for approx.
2 seconds.
– Note –If using the unit on battery power only, the power will turn off automatically if no unit operations
are carried out for 5 minutes, in order to conserve battery power.
The power cannot be turned off while the HDD SAFETY Detection Switch has been activated.
(See below.)
HDD SAFETY Switch
Important: Keep unit on flat, level surface while in
use. If the unit is lifted up or placed on a surface that is
not flat and level, the PC card HDD operation will be
stopped by the HDD SAFETY Switch to protect it from
damage.
If the unit receives a strong impact, the PC Card HDD data may
be corrupted. It is advisable to keep this switch ON.
(ON is the default setting.)
If the HDD SAFETY Detection Switch, located under the unit, is
activated, unit operation will be stopped and a warning message
will appear on the TV screen and unit LCD. In this case, place
unit on a flat, level surface. Normal operation will resume. Any
copy operations resume from precise point where copying was
interrupted.
If the HDD SAFETY Detection Switch is activated while the unit
is connected to a PC, “SAFETY MODE PUT IT DOWN” will
appear on the unit LCD. Copy operation in progress at this time
will be suspended, and computer errors may also occur.
Remaining Battery Life Display
When the BATT.    and the battery icon  start flashing, all buttons, except
power off, are inoperable. Connect the AC adaptor or recharge the battery. If the
battery completely runs down during copying, the copying is stopped and power is
shut off. It may not be possible to play back the data that was being copied at this
time.
It is advisable to fully charge the battery before using the unit. (p. 16)
USB
S/V OUT   DC IN
COPY   TV
MODE
OFF   ON
HDD SAFETYHDD SAFETY
(ON/OFF)
HDD
SAFETY
Detection
In case of a power outage, the unit utilizes the supplied battery as a backup
in order to protect the unit and the card data. If you are using the AC adaptor,
insert a sufficiently charged battery before turning on the power. The unit
cannot be used if only the AC adaptor is used.
HDD stops and all
operations are interrupted.
COPY MODE
BATT.
COPY MODE
BATT.BATTERY
LOWCOPY MODE
BATT.BATT.
COPY MODE
PT1.p14-18.p652003/01/14, 12:36 18 
						

							19
Copy Mode
Copy Mode (Display Indicator)
Liquid Crystal
Display
– Note –Any cards that utilize adaptors other than the accessory PC Card HDD adaptor are displayed
as “PC CARD”.
M
CANCEL
ENU
/SET
Displaying Menu (Indicator Flowchart)
MENU
STANDBY/SETCOPY  T
V
MODE
COPY/TV
MODE
1Set COPY/TV MODE to “COPY”.
2Insert a Card. (p. 17)
3Turn on this unit. (p. 18)
In Copy mode, data can be copied from one
card to another. You can also check card
storage capacity, make backups, set TV
formats, and format cards.
If unit is on battery power only, power shuts off
automatically if you perform no operation for
5 minutes to conserve battery. POWER Lamp
When using battery When using AC adaptor
(When a PC Card
HDD is inserted)
Press SET
If a button is not pressed
within 10 seconds.
Press MENU*
*
“Copying” (p. 21)
“Menus” (p. 20)* When HDD SAFETY is
ON and is activated
(p. 18), the PC Card HDD
cannot be verified, so
always place unit on flat,
level surface.
(When an SD Memory
Card is inserted)
(When a PC Card and SD
Memory Card are inserted)
(When a PC Card
is inser ted)
Follow these steps to display menus in COPY mode.
PT1.p19-23.p652003/01/14, 12:36 19 
						

							20
Copy Mode (Menus)
Liquid Crystal
Display
M
CANCEL
ENU
/SET
MENU
CANCEL
STANDBY/
SETCOPY  T
V
MODE
COPY/TV MODE
PC Card HDD
(PC Card) Slot
Memory Card Slot
Card Storage Capacity Check (MEDIA CAPACITY)
This lets you confirm card storage capacity.
PC Card HDD available space is approx. 4.6 GB.
BACKUP (BACKUP ON/OFF)Set to ON, a backup folder containing your data is automatically created when copying. Useful
where data may become accidentally deleted or corrupt. Backup folder contents are not displayed
in TV mode. A computer can be used to copy, edit, and delete files. (This unit is
factory shipped set to “OFF”.)
TV Format Selection (NTSC/PAL)This unit can be set to the TV format used in your country (NTSC or PAL). NTSC is the TV format
used in countries, such as the United States, Canada and Japan, and PAL is used in some
European countries and Oceania.
Formatting Cards (SD-FORMAT) (HDD-FORMAT)Formatting a card irreversibly erases all contained data.
1Display the menu as described on
page 19.
Press MENU again to exit.
2Press  to select a menu item, then
press SET.
Refer to above for details on menus.
Refer to pages 22 and 23 for details on formatting.
3Press  to select a function, then
press SET.
Selection flashes until SET is pressed.
To make other settings:
Press MENU to return to Step 2.(To perform BACKUP)
(To select TV format)
(Example)
(To check storage capacity)
PT1.p19-23.p652003/01/14, 12:36 20