Panasonic Sc Htr310 E K Operating Instructions

							RQTX0165
11
Removing casters
How to lift the rack
  Lift the back side of the 
top board and insert your 
hand to the bottom of the 
back side. 
  Insert your hand to the 
bottom of the front side. 
  Lift the rack horizontally 
using your both hands.
Remove casters at unstable places. (thick-piled carpet, 
uneven floor, etc.)
Spread soft cloth on the floor and tip the rack back to 
remove the casters.
Hold and pull to remove.
At least 2 people are necessary for removing casters.
Make sure that at least 2 people hold the bottom plate 
when moving the rack after removing the casters. See the 
following instructions about how to lift the rack.
Do not put anything on and in the rack when removing 
casters. Do not put the included glass top panel either.
•
•
•
•
•
•
Connection
Installing and assembling the rack
(Bottom plate)
Hold and pull.
Caster
Front side
Back side
Soft cloth, etc.
Front side Back side
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   117/16/2008   1:51:30 PM
 
						

							RQTX0165
12
Shelf assembly
Installing and assembling the rack
Glass top panel assembly
(Side view)
Adjust the included glass top panel 
so that it lines up with the protrusion 
on the back of the rack.
The glass top panel has the front side and back 
side. Face up the front side with the sticker.
The nonslip sheet has been put on the top panel of 
the rack. Do not remove the sheet when installing 
the glass top panel.
•
•
Put the glass panel down slowly to 
make sure its aligned with the rear of 
the top panel of the rack (as shown 
in the diagram).
Note
Lift up and down slowly not to make an impact on the glass.
1
2
Nonslip 
sheet
Glass top panel
Protrusion
Sticker
Top panel of the rack
Glass top panel Top panel of the rack
1
3
Hole
Groove (Under the shelf)
Shelf
Moulded dowel
Connection
Installing and assembling the rack
UNIT: mm (inches)
Dowel position Upper Middle Lower
Compartment
HUpper shelf 101 (3 31/32”)131 (5 5/32”)161 (6 11/32”)
Lower shelf 101 (3 31/32”)71 (2 25/32”)41 (1 5/8”)
W
448 (17 5/8”) (both L and R)
D 354 (
13 15/16”)
Insert the moulded dowel (included) into 
the dowel hole on one side.
Insert the shelf (included) at an angle 
and adjust it so that the shelf groove is 
attached to the molded dowel.
Hold the shelf, insert the moulded dowel 
into the dowel hole on the other side. Set 
the shelf horizontally.
The height of the shelf can be adjusted at 3 different 
levels.
Change the position of the dowels to move the shelf up or 
down.
Insert the moulded dowel not to lose even when the shelf 
is not set.
•
•
•
2
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   127/16/2008   1:51:32 PM
 
						

							RQTX0165
13
Installing the television (Please also refer to the television’s operating instructions.)
Installing a DVD player/Blu-ray Disc player/DVD recorder or other equipment on 
the shelf 
(Please also refer to the other equipment’s operating instructions.)
1
Press the cut-out on the back panel using 
your thumb etc. with force to remove it for 
wiring after installing the equipment.
Refer to pages 16 to 21 for connections with other 
equipment.
If the operating instructions of the equipment require heat 
release or ventilation, remove the cut-out on the back 
panel to secure ventilation.
W
hen setting equipment with the exhaust hole on the side, 
follow the operating instruction of the equipment before 
setting. 
Pull out the bundled cords of stored 
equipment from the cut-outs for  
connection.
•
•
•
2
Shelf top (dimension ):  348 mm (13 11/16”) 13(Maximum depth of 
equipment when the big cut-outs part on the 
back panel is opened)
Shelf top (dimension 
):  255 mm (10 1/16”) (Maximum depth of 
equipment when the small cut-outs part on 
the back panel is opened)
The lowest level (on the floor panel) (dimension 
): 
  255 mm (10 1/16”) (Maximum depth of 
equipment)
Note
Do not put equipment weighing more than 12 k g 
(26.5 lbs) on the upper shelf or more than 20 k g
 
(44.1 lbs) on the lower shelf.
Image interference may occur if you put a DVD 
recorder, etc. on the upper shelf. Put it on the lower 
shelf if this occurs.
Depending on the equipment to install, the cables 
may not be connected. 
To install the equipment, adjust the height of the shelf 
to the position where the cables come out.
If you set on the lowest level (on the floor panel), the 
equipment with long depth may not be set properly or 
the equipment cord may not be taken out.
When installing equipment, refer to the table for “Shelf 
assembly” on page 12.
•
•
•
•
• (Rear vie
 w)
Cut-outs P
 ush the black-circled 
point.
Shelf top
(Side view in cross section)
Place the television (with stand attached) 
in the center of the rack.
Recommended:  50 inches or less
Television 
stand
Note
Lift the television when placing it on the rack. Dragging it may 
damage the top panel. 
(For details, refer to the television’s operating instructions.)
If the television stand adheres to the glass top panel too tight to 
remove, lift the stand inserting a fl
 at and thin object. This may help 
removing the stand.
Install the rotary television stand not to run over the rack even if it 
rotates.
•
•
• (Fr
 ont view)
The lowest level (on the floor panel) Small cut-outs
Big cut-outs
Connection
Installing and assembling the rack
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   137/16/2008   1:51:35 PM
 
						

							RQTX0165
14
Setting the caster stoppers
y
Stabilising the television
  
Attach the television to the rack to prevent it from falling over.
  Fixing to the rack
Attach the fall-prevention band etc. supplied with TV using 
the included screws as illustrated at right. (If the fall-pre-
vention band is not supplied with TV, use a commercially 
available band to fix.)
Attach the fall-prevention band to the prepared hole in the 
center of the underside of the top board.
If the hole is not positioned at a suitable place, drill  
approx. 2 mm (
3/32”) hole on the underside and attach the 
band with the screw.
If you fasten the screw too tightly, it goes around in circles 
and the TV cannot be fixed.
  Fixing to the wall
Use commercially available screws, strong string or chain 
suitable for materials of the wall or pillar to fix to the solid 
parts.
Walls and pillars must be strong enough to support the 
weight of TV. Ask installation personnel for more informa-
tion.
Fix 2 parts at both left and right.
•
•
•
•
•
(Setup example)
The illustration is an example.
The shape may differ from the actual product.
(Setup e
 xample)
Set the caster stoppers (included) under 
the casters to fix this system and prevent 
from moving. 
When setting the caster stoppers, match the front side of 
caster with the arrow of the caster stopper.
Lift the rack to remove caster stoppers. See page 11 
about how to lift the rack.
•
• (Caster stopper position)
Set the caster stoppers under 4 casters circled with the 
dotted line of figure below.
Connection
Installing and assembling the rack
Installing and assembling the rack
Prepared 
screw hole
Fall-prevention 
band
Front
Caster stopper
Arro
 w Front side
(Bottom side)
Screw (included)
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   147/16/2008   1:51:37 PM
 
						

							RQTX0165
15
Glass door assembly
Remove 4 screws from the glass holder 
using a Phillips-head screwdriver and 
take out the board.
Before taking out the board, remove the tape fixing the 
glass holder.
Use the Phillips-head screwdriver that matches the screw 
size.
Insert the glass door (included) to the 
glass holder firmly and tighten  
the 2 screws in front tentatively.
The illustration at right shows how to fix the left glass door.
One side of the magnet catch has a hole. 
This is the inner side of the glass.
The slippage prevention sheet is pasted on the glass 
holder inserting part on the surface of the glass door.  
Fix as it is.
Close the glass door to adjust the height 
and gap on both sides. Open the glass 
door so it does not misalign and tighten 
2 screws in front with the Phillips-head 
screwdriver.
Tighten 2 screws at the back firmly.
Install the other glass door in the same way.
•
•
•
•
•
•
1
2
3
4
Board
Glass 
holder
Magnet 
catch
Hole
Slippage prevention sheet Phillips-head 
screwdriver
Screw
Screw
Screw Screw
I

nner side 
of glass
Screw
Inner side 
of glass
Inner side 
of glass Phillips-head 
screwdriver
Phillips-head 
screwdriver
Screw
Connection
Installing and assembling the rack
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   157/16/2008   1:51:39 PM
 
						

							RQTX0165
16
Basic connections
Connection
Home Theater connections
Reduce the volume on the television and select “TV ” after you have done connections as 
above if you want to use this system.
TV
Audio out R     L
Use this connection 
so audio from the 
equipment can be 
heard through the 
television’s speakers 
even if this system is 
in standby mode.
AUDIO IN
Video 
cab
 le Audio 
cable
Amplifier
DVD player etc. VIDEO OUT A
 UDIO 
OUT
Stereo connection cable (not included)
Connection cable
Refer to the operating instructions for the equipment you are connecting for the correct type of video cable.
•
Home Theater connections
Connect the video 
directly from the 
other equipment to 
the television. 
VIDEO IN
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   167/16/2008   1:51:40 PM
 
						

							RQTX0165
17
Turn off all components before making any connections.
To connect equipment, refer to the appropriate operating 
instructions.
•
•
Connection
Home Theater connections
Audio 
cable
HDMI cable notes
Use a Panasonic HDMI cable for best results.
•
HDMI cable (not included)Optical fiber cable (not included)
Connecting the optical 
fiber cable
Note the 
shape and fit 
it correctly 
into the 
terminal. Do not 
bend!
Connecting equipment with HDMI terminal (TV, DVD recorder, etc.)
Connection cable
HDMI inputDigital audio 
out (optical) TV
Blu-ray Disc player/DVD 
recorder, etc. HDMI 
Video/Audio out
Make the connection either   or 
 according to 
the suitability for your equipment.
Amplifier
Audio out
R     L
Stereo connection cable  
(not included)
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   177/16/2008   1:51:42 PM
 
						

							RQTX0165
18
Home Theater connections
Connecting the optical fiber 
cable
Note the shape 
and fit it  
c

orrectly into the 
terminal. Do not 
bend!
Optical fiber cable (not included)
Connecting with digital terminal-mounted equipment
Connection cable
Refer to the operating instructions for the equipment you are connecting for the correct type of video cable.
•
TV
Digital audio out (optical)
Connect the video 
directly from the 
other equipment to 
the television. 
VIDEO IN AUDIO IN
Use this connection 
so audio from the 
equipment can 
be heard through 
the television’s 
speakers even if 
this system is in 
standby mode.
Video cable Audio 
cable
Amplifier
DVD player etc.
Digital audio out 
(optical) VIDEO OUT
AUDIO OUT
Coaxial cable (not included)Digital audio out
(coaxial)
Connection
Home Theater connections
Make the connection either   or 
 according to the suitability for your 
equipment.
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   187/16/2008   1:51:44 PM
 
						

							RQTX0165
19
Turn off all components before making any connections.
To connect equipment, refer to the appropriate operating 
instructions.
•
•
Optical fiber cable (not included)
Connection
Home Theater connections
Stereo connection cable (not included)
Connecting the optical fiber 
cable
Note the shape 
and fit it  
c

orrectly into the 
terminal. Do not 
bend!
Connecting with VCR
Connection cable
Refer to the operating instructions for the equipment you are connecting for the correct type of video cable.
•
TVConnect the video 
directly from the 
other equipment to 
the television. 
VIDEO IN AUDIO IN
Use this connection 
so audio from the 
equipment can 
be heard through 
the television’s 
speakers even if 
this system is in 
standby mode.
Video cable
Audio 
cable
Amplifier
VCR etc.
VIDEO OUT
AUDIO OUT
Digital audio 
out (optical)
R     L
A

udio out
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   197/16/2008   1:51:45 PM
 
						

							RQTX0165
20


Connecting the optical fiber 
cable
Note the 
shape and fit it 
correctly into 
the terminal.Do not bend!
Connection cable
Optical fiber cable (not included)
Connecting a set top box (cable or satellite)
Connect the video 
directly from the 
other equipment to 
the television. 
VIDEO IN
Use this 
connection so 
audio from the 
equipment can 
be heard through 
the television’s 
speakers even if 
this system is in 
standby mode.
AUDIO IN TV
Video 
cable Audio 
cable
VIDEO OUT AUDIO
OUT
Cable box or  
satellite receiver, etc.
Digital audio  out 
(optical)
Refer to the operating instructions for the equipment you are connecting for the correct type of video cable.
•
Amplifier
DVD player etc.
Digital audio out
(coaxial)
Digital audio 
out (optical)
Connection
Other connections
Other connections
Coaxial cable (not included)
SC-HTR310 (RQTX0165-P) - 14.07.08.indd   207/16/2008   1:51:47 PM