Panasonic Sc Htb8 Owners Manual

							Getting started
VQT5J4111
Precautions
Choose a placement method that suits you best.
∫When placing the main unit in front of the TV
The main unit may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic 
Tracking System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D 
compatible TV.
≥If interference occurs, move the main unit further away from the TV. If the TV still does not function 
correctly, try using it in a rack or in the wall mount position.
∫ If the TV’s remote control sensor is blocked by the main unit
Try using the TV’s remote control from a different angle.
	≥Do not use the main unit in a metal cabinet.
≥ If irregular coloring occurs on your TV, turn the TV off for  about 30 minutes. If it persists, move the main unit further 
away from the TV.
≥ Keep magnetized items away. Magnetized cards, watches, etc., can be damaged if placed too close to the main unit.
≥ Keep the main unit approximately 150 mm (6 q) away from the TV.
Selecting the placement method
When placing the main unit 
on a rack or on a table
≥ Place the main unit on a flat 
and horizontal surface.
≥ Place the main unit in front of 
the TV pedestal.
When attaching the main 
unit to a wall
≥Place the main unit on a 
flat and vertical surface. Page 12
Page 13
SC-HTB8P_VQT5J41_P.book  11 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							12VQT5J41
Additionally required accessories (commercially available)
≥Fall prevention cord  .......................................................................................................... ...........  k 1
≥ Screw eye (to attach the fall prevention cord)...............................................................................   k 1
	≥Use commercially available screws that are capable of supporting over 33 k g (73 lbs).
≥ Use a cord that is capable of supporting over 10 k g (22 lbs) (with a diameter of about 2 mm (3/32q)).
Slide the MULTI ANGLE switch to “RACK/TABLE TOP”.
≥ Press the AC power supply cord into the holder.
Attach the cord to the main unit.
A Cord§
§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations, 
about 5 mm (3/16q) apart from the tip, at an angle of 45o (as illustrated above).
Place the main unit in the desired position and attach the cord onto the rack or table.≥ Make sure that the slack of the cord is minimal.
≥ Do not lean the main unit against the TV or wall.
≥ Do not place the main unit over the AC power supply cord.
≥ Ensure that the main unit is stable.
B Screw eye≥Attach at a position capable of supporting over 10 k g (22 lbs).
≥ Depending on the placement of the main unit, the screwing position of the screw eye may differ.
When placing the main unit on a rack or on a table


SC-HTB8P_VQT5J41_P.book  12 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							Getting started
VQT5J4113
Precautions
Make sure that the screw used and the wall are strong enough to support the weight of at least 33 kg (73 lbs).The screws and other items are not supplied as the type and size will vary with each installation.
≥Refer to step 3 for details about the required screws.
≥ Be sure to attach the fall prevention cord as a secondary safety measure.
Additionally required accessories (commercially available)
≥Screws for wall mounting ....................................................................................................... ......  k 2
≥ Fall prevention cord ........................................................................................................... ........... k 1
≥ Screw eye (to attach the fall prevention cord) ..............................................................................  k 1
	≥Use a cord that is capable of supporting over 10 k g (22 lbs) (with a diameter of about 2 mm (3/32q)).
Slide the MULTI ANGLE switch to “WALL MOUNT”.
Attach the cord to the main unit.
A Cord§
§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations, 
about 5 mm (3/16q) apart from the tip, at an angle of 45o (as illustrated above).
When attaching the main unit to a wall

SC-HTB8P_VQT5J41_P.book  13 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							14VQT5J41
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥ Leave at least 20 mm (25/32q) of space above of the main unit to allow enough space for fitting the main unit.
≥ Leave at least 10 mm (13/32q) of space on both sides of the main unit. Without sufficient space, it is not possible to 
mount the main unit successfully.
≥ Be sure to use a level to insure that both mounting holes are level to each other.
Front view (semi-transparent image)
Fit the main unit securely onto the screw(s).
Secure the cord to the wall.
≥Make sure that the slack of the cord is minimal.
M Screw eye
N Cord B
At least 30 mm (1
3/16q)
C ‰4.0 mm (5/32q)
D ‰7.5 mm to ‰9.4 mm (9/32q to 3/8q)
E Wall or pillar
F 7.5 mm to 8.5 mm (
7/32q to 11/32q)
G 320 mm (12
19/32q) H215 mm (815/32q) I215 mm (815/32q)
J 15 mm (19/32q) K115 mm (417/32q) LWall mounting hole
DODO NOT
≥Move the speaker so 
that the screw is in this 
position.≥In this position, the 
speaker will likely fall if 
moved to the left or right.

 

\b 

\f
\f


SC-HTB8P_VQT5J41_P.book  14 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							Getting started
Operations
VQT5J4115
Precautions
OperationsUsing this system
Preparation≥Turn on the TV and/or connected device.
Press [ Í] to turn on the main unit.
Select the source.
≥ This remote control cannot be used to control the operations 
of the connected devices.
∫ When “ ” is selected as the source
On the Bluetooth® device:
Select this system as the output source of the 
connected Bluetooth
® device and start the 
playback.
∫ When “BD/DVD” is selected as the 
source
On the TV and the connected device:
Select the TV’s input for this system and start the 
playback on the connected device.
∫ To adjust the volume of this system
Press [ iVOL j].≥Volume range: 0 to 100§
∫ To set the surround modeYou can enable/disable the surround effect.Press [SURROUND].≥To cancel, press the button again.
∫ To set the clear voice modeWith the clear voice mode you can hear dialogs clearer.Press [CLEAR VOICE].≥To cancel, press the button again.
∫ To  m u t e  t h e  s o u n d
Press [MUTE].≥While muting, all the indicators blink simultaneously.
≥ To cancel, press the button again or adjust the volume.
≥ Muting is canceled if the main unit is turned off.
	
§ BD/DVD indicator, Bluetooth® indicator and sound mode indicators blink from left to right (i) or from right to left (s) while adjusting.
The indicators will not blink when it has reached the maximum or minimum.
≥ If there is sound coming out of the TV’s speakers, reduce the volume of the TV to its minimum.
≥ If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically 
lower the volume to the middle (50) when the main unit is turned on (Volume limitation).
To turn this function off, refer to page 16.
PressTo select
[INPUT] “TV” 
--------------#  “BD/DVD”
^---  “ ” (Bluetooth
®) !-}
[] “ ” (Bluetooth®)
CLEAR VOICE
SURROUND
PAIRING----
INPUT
If this system does not operate as expected or sound is unusual, returning the settings to the 
factory preset may solve the problem. ( >p. 17)
SC-HTB8P_VQT5J41_P.book  15 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							16VQT5J41
Advanced operations
The main unit is automatically turned off if there is no audio 
input and when you do not use it for approx. 2 hours.
While pressing and holding 
[CLEAR VOICE] on the remote 
control, press and hold [INPUT] on 
the main unit for more than 4 sec to 
display the current setting.
While the setting is displayed, press 
[CLEAR VOICE] to select the setting.
≥The setting changes each time [CLEAR VOICE] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and 
then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.
This function allows you to connect a paired Bluetooth® 
device when the main unit is in standby mode.
While pressing and holding 
[SURROUND] on the remote control, 
press and hold [ ] on the main unit 
for more than 4 sec to display the 
current mode.
While the mode is displayed, press 
[SURROUND] to select the mode.
≥ The setting changes each time [SURROUND] is pressed.
≥ The indicator for the selected setting blinks for 20 sec and 
then exits the setting mode.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is off.
You can turn off dimmer mode and keep the LED 
indicators bright.
While pressing and holding [INPUT] on 
the remote control, press and hold 
[s VOL] on the main unit for more than 
4 sec to turn off Dimmer mode.
≥ The indicator for the current condition will turn brighter.
≥ The setting is maintained until it is changed again.
≥ Default setting of this function is on.
	To turn on dimmer mode, repeat the operation above.
After performing the operation, the indicator for the current 
condition will be dim.
∫ Remote control codeWhen other Panasonic devices respond to this system’s 
remote control, change the remote control code on this 
system and the remote control.
Preparation≥Turn off all other Panasonic products.
≥ Turn on the main unit.
Change the remote control code to code 2:
1 Aim the remote control at the main unit’s 
remote control sensor.
2 Press and hold [MUTE] and [ ] on the remote  control for more than 4 sec.
≥All the indicators will blink for 10 sec when the code of 
this system is changed.
≥ The setting is maintained until it is changed again.
	≥ If the main unit does not operate after changing the code, 
repeat steps 1 and 2.
≥ To change the remote control code to code 1, repeat the 
steps above, but replace 
[] with [INPUT].
∫ To turn off the volume limitation
If a state of the lowered volume disturbs you every time 
the main unit turns on, for example, it is possible to turn off 
this function as follows:
While pressing and holding [MUTE] on the remote control, 
press and hold [VOLi] on the main unit for more than 4 sec.≥All the indicators will blink once when the volume limitation 
is turned off.
	To reset the setting, return to the factory preset. ( >p. 17)
Auto Power Down
“BD/DVD” indicator blinks:
Auto Power Down is on.
“CLEAR VOICE” indicator blinks:
Auto Power Down is off.
Bluetooth® Stand-by
“BD/DVD” indicator blinks:
Bluetooth® Stand-by is on.
“CLEAR VOICE” indicator blinks:
Bluetooth
® Stand-by is off.
0ã0å0Ð0å0÷0å
0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ
0ã0å0Ð0å0÷0å
0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ
Dimmer mode
Others
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
SC-HTB8P_VQT5J41_P.book  16 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							Reference
Operations
VQT5J4117
ReferenceTroubleshooting
Before requesting service, make the following checks. If 
you are in doubt about some of the check points, or if the 
solutions indicated in the following guide do not solve the 
problem, refer to “Customer Services Directory (United 
States)” on page 22.
No power.≥Insert the AC power supply cord securely. ( >p. 8)
≥ If the indicators blink and the main unit turns off 
immediately after you have turned it on, unplug the AC 
power supply cord and consult your dealer.
The remote control does not work properly.≥The battery is depleted. Replace it with a new one. 
(> p. 7)
≥ It is possible that the insulation sheet has not been 
removed. Remove the insulation sheet. ( >p. 7)
≥ It may be necessary to set the code of the remote 
control again after changing the battery of the remote 
control. ( >p. 16)
≥ Use the remote control within the correct operation 
range. ( >p. 7)
The “TV” indicator blinks.Unplug the AC power supply cord and consult your dealer. 
If other indicators are also blinking, be sure to inform your 
dealer of these indicators.
The main unit is automatically switched to 
standby mode.
“Auto Power Down” function is on.
The main unit will automatically switch to standby mode 
when no signal is input and no operation is performed for 
approx. 2 hours. Refer to page 16 to turn this function off.
Pairing cannot be done.Check the Bluetooth® device condition.
The device cannot be connected.≥The pairing of the device was unsuccessful or the 
registration has been replaced. Try pairing the device 
again. ( >p. 9)
≥ This system might be connected to a different device. 
Disconnect the other device and try pairing the device 
again.
The device is connected but audio cannot be 
heard through this system.
For some built-in Bluetooth® devices, you have to set the 
audio output to “SC-HTB8” manually. Read the operating 
instructions for the device for details.
The sound is interrupted.≥The device is out of the 10 m (33 ft) communication range. 
Bring the Bluetooth® device closer to the main unit.≥ Remove any obstacle between the main unit and the 
device.
≥ Other devices that use the 2.4 GHz frequency band 
(wireless router, microwaves, cordless phones, etc.) are 
interfering. Bring the Bluetooth
® device closer to the 
main unit and distance it from the other devices.
To return to the factory defaults.
While the main unit is on, press and hold [ Í/I] on 
the main unit for more than 4 sec.
(All the indicators will blink twice when this 
system is reset.)
If this system does not operate as expected, 
returning the settings to the factory defaults 
may solve the problem.
≥
The remote control code will return to “1” when 
this system is returned to the factory preset. To 
change the remote control code, refer to page 16.
General operation
Bluetooth®
SC-HTB8P_VQT5J41_P.book  17 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							18VQT5J41
No sound.≥Turn muting off. ( >p. 15)
≥ Check the connections to the other device. ( >p. 8)
≥ Make sure that the received audio signal is compatible 
with this system. ( >p. 21)
≥ Turn this system off and then on again.
≥ If the connections are correct, there might be a problem 
with the cables. Redo the connections with different 
cables.
≥
Check the audio output settings on the connected device.
The volume is lowered when the main unit is 
turned on.
If the main unit is turned off with the volume setting in the 
greater half (above 50), the main unit will automatically 
lower the volume to the middle (50) when the main unit is 
turned on. ( >p. 16)
The dialog is too persistent or the dialog does 
not sound natural.
This system has a function to make the dialog stand out 
when the volume is low. ( >p. 15)
There is no audio.
The power of the main unit turns off 
automatically.
(When the main unit detects a problem, a safety measure 
is activated and the main unit automatically switches to 
standby mode.)
≥There is a problem with the amplifier.
≥ Is the volume extremely high?
If so, lower the volume.
≥ Is this system placed in an extremely hot place?
If so, move this system to a cooler place and wait a few 
moments and then try to turn it on again.
If the problem persists, check if the TV indicator and the 
BD/DVD indicator are blinking  first. After checking the 
indicators, turn off this system, unplug the AC power 
supply cord, and consult your dealer. Make sure to 
remember which indicators were blinking and inform the 
dealer of them.
Sound
SC-HTB8P_VQT5J41_P.book  18 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							Reference
VQT5J4119
About Bluetooth®
∫Frequency band usedThis system uses the 2.4 GHz frequency band.
∫Certification of this device≥This system conforms to frequency restrictions and has 
received certification based on frequency laws. Thus, a 
wireless permit is not necessary.
≥ The action below are punishable by law in some 
countries:
jTaking apart or modifying the unit.
j Removing specification indications.
∫ Restrictions of use≥Wireless transmission and/or usage with all Bluetooth® 
equipped devices is not guaranteed.
≥ All devices must conform to standards set by Bluetooth 
SIG, Inc.
≥ Depending on the specifications and settings of a 
device, it can fail to connect or some operations can be 
different.
≥ This system supports Bluetooth
® security features. But 
depending on the operating environment and/or 
settings, this security is possibly not sufficient. Transmit 
data wirelessly to this system with caution.
≥ This system cannot transmit data to a Bluetooth
® 
device.
∫ Range of useUse this device at a maximum range of 10 m (33 ft).
The range can decrease depending on the environment, 
obstacles or interference.
∫Interference from other devices≥This system may not function properly and troubles 
such as noise and sound jumps may arise due to radio 
wave interference if the main unit is located too close to 
other Bluetooth
® devices or the devices that use the 
2.4 GHz band.
≥ This system may not function properly if radio waves 
from a nearby broadcasting station, etc. are too strong.
∫ Intended usage≥This system is for normal, general use only.
≥ Do not use this system near equipment or in an 
environment that is sensitive to radio frequency 
interference (example: airports, hospitals, laboratories, 
etc).
Unit care
∫ Clean this system with a soft, dry cloth≥When dirt is heavy, wring a cloth moistened in water 
tightly to wipe the dirt, and then wipe it with a dry cloth.
≥ Never use alcohol, paint thinner or benzine to clean this 
system.
≥ Before using chemically-treated cloth, carefully read the 
instructions that came with the cloth.
∫ To dispose or transfer this systemThis system may keep the user settings information in the 
main unit. If you discard the main unit either by disposal or 
transfer, then follow the procedure to return all the settings 
to the factory presets to delete the user settings.
(> p. 17, “To return to the factory defaults.”)
≥ The operation history may be recorded in the memory 
of the main unit.
License
Panasonic bears no responsibility for data 
and/or information that is compromised 
during a wireless transmission.
The Bluetooth® word mark and logos are owned by the 
Bluetooth SIG, Inc. and any use of such marks by 
Panasonic Corporation is under license. Other trademarks 
and trade names are those of their respective owners.
SC-HTB8P_VQT5J41_P.book  19 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分 
						

							20VQT5J41
Indicator illumination
The indicators display the condition of this system by flashing. The indicator patterns illustrated below 
are displayed during normal operational conditions. They do not refer to the indications of a problem.
Indicator Description
The indicator blinks for 20 sec.
≥ When the setting is on 
( “Auto Power Down” and “Bluetooth
® Stand-by”) ( >p. 16)
The indicator blinks for 20 sec.
≥ When the setting is off 
( “Auto Power Down” and “Bluetooth
® Stand-by”) ( >p. 16)
The indicators blink for 10 sec.
≥ When the remote control code is changed ( >p. 16)
The indicators blink once.
≥ When changing the setting 
( “To turn off the volume limitation”) ( >p. 16)
The indicators blink twice.
≥ When the main unit is reset ( >p. 17)
Bluetooth
® indicator blinks quickly.
≥ When the main unit is ready for pairing ( >p. 9)
Bluetooth
® indicator blinks slowly.
≥ When the main unit is waiting to connect ( >p. 9)
Bluetooth
® indicator turns on.
≥ When the main unit is connected with a Bluetooth® device 
( > p. 9)
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
0õ0÷0ã0å0Ð0å0÷0å0ä0í0æ0â0ó0Á0÷0ð0ê0ä0æ 0ô0ö0ó0ó0ð0ö0ï0å
SC-HTB8P_VQT5J41_P.book  20 ページ  ２０１４年３月２４日　月曜日　午前１０時３５分