Panasonic Sc Htb580 Owners Manual

							Getting started
RQT992211
This system cannot pass-through the 4K content of a 4K compatible equipment to a 4K Ultra HD TV. 
However, you can connect the system to a 4K Ultra HD TV to enjoy the 4K content.
AHDMI cable
	≥Refer to the operating instructions of the 4K Ultra HD TV (VIERA) and the 4K/60p compatible equipment for setup and for 
playing the 4K content.
≥To enjoy multi-channel output from this system, set the audio output of other equipment to Bitstream.
≥The audio signal input to this system is up to 5.1 channels.
With the IR Blaster connection, it is possible to send the IR signal received by this system’s remote 
control signal sensor to the TV’s sensor.
Use the TV’s remote control within the operation range of this system’s remote control signal sensor.
≥For the operation range, refer to page 8.
Connect the jack plug to the main unit’s Ir SYSTEM terminal.
Connection to a 4K Ultra HD TV
Using the IR Blaster
HDMI IN (ARC)
HDMI OUT
HDMI IN (4K)
AV OUT
TV(ARC)
A
A
e.g., Blu-ray Disc player
(4K compatible)TV
Connect both ends 
to ARC compatible 
HDMI terminals.
(4K compatible)
Ir SYSTEM
Infrared emitter
SC-HTB580P_RQT9922-Y.book  11 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							12RQT9922
Place the infrared emitter in sight of the TV’s remote control signal 
sensor.
≥For the location of the TV’s remote control signal sensor, refer to the operating instructions for the TV.
Aim the TV’s remote control at this system’s remote control sensor and 
operate the TV.
≥For the location of this system’s remote control signal sensor, refer to page 8.
≥Make sure to clean the surface, where the adhesive tape is to be attached.
≥If you peel off the adhesive tape, the surface may become damaged and exposed adhesive may remain. Once you have 
confirmed the TV is operating correctly, secure it by attaching the adhesive tape.
	≥The supplied IR Blaster is only compatible with Panasonic TVs.
∫Placement example
On the rear of the main unit:
≥Connect only after all other connections are completed.
ATo an AC outlet
BAC power supply cord (supplied)
≥This system consumes a small amount of AC power (>p. 30) even when it is turned off. In the interest 
of power conservation, if you will not be using this system for a long time, unplug it from the AC outlet.
AC power supply cord connection
TV remote control 
signal sensorAdhesive tape (supplied)


AC IN 
SC-HTB580P_RQT9922-Y.book  12 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							Getting started
Precautions
RQT992213
Step 2  Placement
	≥Do not hold the main unit in one hand to avoid injury, you may drop the main unit when carrying it.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
When carrying the active subwoofer
To avoid interference, maintain the following distances between the main unit/active subwoofer 
and other electronic devices that use the same radio frequency (2.4 GHz band).
Safety Precautions
Professional installation is required.
The installation should never be done by any other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY DAMAGE AND/OR SERIOUS INJURY, INCLUDING 
DEATH RESULTING FROM IMPROPER INSTALLATION OR INCORRECT HANDLING.
≥Be sure to install the main unit as indicated within this Owner’s Manual.
≥Attach using techniques suited to the structure and materials of the installation location.
Caution
≥This system is to be used only as indicated in these instructions. Failure to do so may 
lead to damage to the amplifier and/or the speaker, and may result in the risk of fire. 
Consult a qualified service person if damage has occurred or if you experience a 
sudden change in performance.
≥Do not attempt to attach the main unit to a wall using methods other than those 
described in this manual.
The active subwoofer
ADo not hold the active subwoofer from this 
opening.
The parts inside may get damaged.
BAlways hold the bottom of the active subwoofer when 
moving it.
Wireless interference
CMain unit/active subwoofer
DWireless router, cordless phone and 
other electronic devices: approx. 2 m 
(6
1/2 ft)
A
B
D
C
SC-HTB580P_RQT9922-Y.book  13 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							14RQT9922
Choose a placement method that suits you best.
∫When placing the main unit in front of the TV
The main unit may block or interfere with the TV’s various sensors (C.A.T.S. (Contrast Automatic 
Tracking System) sensor, remote control sensor, etc.) and the 3D Eyewear transmitters on a 3D 
compatible TV.
≥If interference occurs, move the main unit further away from the TV. If the TV still does not function 
correctly, try using it in a rack or in the wall mount position.
∫If the TV’s remote control sensor is blocked by the main unit
Try using the TV’s remote control from a different angle. If the problem persists, you can use the supplied 
IR Blaster to relay the signal to the TV. (>p. 11, 12)
	≥Place the active subwoofer within a few meters of the main unit and in a horizontal position with the top panel facing upward.
≥Do not use the main unit or the active subwoofer in a metal cabinet.
≥Placing the active subwoofer too close to the walls and corners can result in excessive bass. Cover walls and windows with 
thick curtains.
≥If irregular coloring occurs on your TV, turn the TV off for about 30 minutes. If it persists, move the main unit and active 
subwoofer further away from the TV.
≥Keep magnetized items away. Magnetized cards, watches, etc., can be damaged if placed too close to the main unit and active 
subwoofer.
Selecting the placement method
When placing the main unit 
on a rack or on a table
≥Place the main unit on a flat 
and horizontal surface.
When attaching the main 
unit to a wall
≥Place the main unit on a 
flat and vertical surface.Page 15
Page 16
SC-HTB580P_RQT9922-Y.book  14 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							Getting started
Precautions
RQT992215
Additionally required accessories (commercially available)
≥Fall prevention cord  ......................................................................................................................  k 2
≥Screw eyes (to attach the fall prevention cord) .............................................................................  k 2
	≥Use commercially available screws that are capable of supporting over 26 kg (57.3 lbs).
≥Use a cord that is capable of supporting over 26 kg (57.3 lbs) (with a diameter of about 1.5 mm (1/16q)).
Attach the cord to the main unit.
ACord§
§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations, 
about 5 mm (3/16q) apart from the tip, at an angle of 45o (as illustrated above).
Place the main unit in the desired position and attach each cord onto the 
rack or table.
≥Make sure that the slack of the cord is minimal.
≥Do not lean the main unit against the TV or wall.
BScrew eye≥Attach at a position capable of supporting over 26 kg (57.3 lbs).
≥Depending on the placement of the main unit, the screwing position of the screw eye may differ.
When placing the main unit on a rack or on a table



SC-HTB580P_RQT9922-Y.book  15 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							16RQT9922
The main unit can be wall mounted using the supplied wall mount brackets, etc. Make sure that the 
screw used and the wall are strong enough to support the weight of at least 26 kg (57.3 lbs).
The screws and other items are not supplied as the type and size will vary with each installation.
≥Refer to step 3 for details about the required screws.
≥Be sure to attach the fall prevention cord as a secondary safety measure.
Supplied accessories
Additionally required accessories (commercially available)
≥Screws for wall mounting .............................................................................................................  k 2
≥Fall prevention cord .....................................................................................................................  k 2
≥Screw eyes (to attach the fall prevention cord) ............................................................................  k 2
	≥Use a cord that is capable of supporting over 26 kg (57.3 lbs) (with a diameter of about 1.5 mm (1/16q)).
Attach the cord to the main unit.
ACord§
§ If the cord cannot be threaded through the holes, try bending the cord in 2 locations, 
about 5 mm (3/16q) apart from the tip, at an angle of 45o (as illustrated above).
When attaching the main unit to a wall
∏2Screws∏2 Wall mount brackets


SC-HTB580P_RQT9922-Y.book  16 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							Getting started
Precautions
RQT992217
Attach the wall mount brackets to the main unit.
AWall mount bracket (supplied)
BScrew (supplied)
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥Leave at least 100 mm (315/16q) of space above of the main unit to allow enough space for fitting the main unit.
≥Position the main unit with at least 50 mm (2q) of free space to its right. If not, it may not be possible to access the buttons.
≥Be sure to use a level to insure that both mounting holes are level to each other.
Front view (semi-transparent image)CAt least 30 mm (1
3/16q)
D‰4.0 mm (5/32q)
E‰7.0 mm to ‰9.4 mm (9/32q to 3/8q)
FWall or pillar
G1.6 mm to 2.5 mm (
1/16q to 3/32q)
H400 mm (15
3/4q)I275 mm (1013/16q)J275 mm (1013/16q)
K27 mm (11/16q)L11 0 m m  ( 411/32q)MWall mounting hole






 





SC-HTB580P_RQT9922-Y.book  17 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							18RQT9922
Fit the main unit securely onto the screw(s).
Secure the cord to the wall.
≥Make sure that the slack of the cord is minimal.
AScrew eye
BCord
DODO NOT
≥Move the speaker so 
that the screw is in 
this position.≥In this position, the 
speaker will likely fall 
if moved to the left or 
right.


SC-HTB580P_RQT9922-Y.book  18 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							Getting started
Precautions
RQT992219
Step 3  Wireless connections
Preparation
≥Turn on the main unit.
Press [BÍ CI].
Active subwoofer on/off button [B Í C I]
Use this button to turn the active subwoofer on 
and off.
C I:
The active subwoofer is on.
B Í:
The active subwoofer is off.
The active subwoofer will still consume a small 
amount of power even when it is turned off (
B, Í).
Check that the wireless link is 
activated.
WIRELESS LINK indicator
Lights red:
The wireless link is not activated.
Lights green:
The wireless link is activated.
Blinks green:
The active subwoofer is trying to activate the 
wireless link with the main unit.
	The wireless link will be activated when the main unit and the 
active subwoofer are both turned on.
By using the Bluetooth® connection, you can listen 
to the sound from the Bluetooth® audio device 
from this system wirelessly.
≥Refer t o the operating instructions of  t he Bluetooth® device for 
further instruction on how to connect a Bluetooth® device.
Preparation
≥Turn on the Bluetooth® feature of the device and 
place the device near the main unit.
Press [ ] to select “BLUETOOTH”.
≥If “PAIRING” is indicated on the display, go to step 3.
Press and hold [ ] until “PAIRING” 
is indicated on the display.
Select “SC-HTB580” from the 
Bluetooth® device’s Bluetooth® menu.
≥If prompted for the passkey on the Bluetooth® device, enter “0000”.≥Once the Bluetooth® device is connected, the name of the 
connected device will be indicated on the display for a few 
seconds.
	≥You can register up to 8 devices with this system. If a 9th 
device is paired, the device that has not been used the 
longest will be replaced.
Press [ ] to enter Bluetooth® mode.
“BLUETOOTH READY” is indicated on the display.
Select “SC-HTB580” from the 
Bluetooth® device’s Bluetooth® menu.
∫Disconnecting a Bluetooth® device
Press and hold [ ] until the “BLUETOOTH 
READY” is indicated on the display.
	≥When “BLUETOOTH” is selected as the source, this 
system will automatically try and connect to the last 
connected Bluetooth
® device.
≥The Bluetooth® device will be disconnected if a different 
audio source (e.g. “TV”) is selected.
≥
This system can only be connect ed to one device at a time.≥To change the sound quality, refer to page 24 “LINK MODE”.
Active subwoofer 
wireless connectionBluetooth® connection
Bluetooth® pairing
Connecting a paired 
Bluetooth® device
SC-HTB580P_RQT9922-Y.book  19 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分 
						

							20RQT9922
For NFC-compatible AndroidTM devices only
Simply by touching an NFC (Near Field 
Communication)-compatible Bluetooth
® device on 
the main unit, you can complete all preparations, 
from registering a Bluetooth
® device to 
establishing a connection.
≥Android device version lower than 4.1 requires 
the installation of the app “Panasonic Music 
Streaming” (Free of charge). Download the app 
to your Bluetooth
® device.– Enter “Panasonic Music Streaming” in the search 
box of Google PlayTM to search, and then select 
“Panasonic Music Streaming”.
Preparation
≥Turn on the NFC feature of the device.
Press [ ] to select “BLUETOOTH”.
Touch and hold your device on the 
NFC touch area of the main unit [ ]. 
(>p. 6)
– Once the registration and connection of the 
Bluetooth® device is complete, the name of the 
connected device is indicated on the display for a 
few seconds. Move the device away from the main 
unit.
≥When the connection is not established even if your 
device has touched the NFC touch area, move the 
device so it can be detected.
Start playback on the Bluetooth® 
device.
	≥If you touch another device to the main unit, you can 
update the Bluetooth® connection. The previously 
connected device will be disconnected automatically.
≥If the image and sound are out of sync during playback, 
restart the playback app you are using.
≥The One-Touch Connection may not work properly 
depending on the type of device being used.
Remote control code
When other Panasonic devices respond to this 
system’s remote control, change the remote 
control code on this system and the remote 
control.
Preparation
≥Turn off all other Panasonic products.
≥Turn on the main unit.
∫To set the code to “REMOTE 2”
Press and hold [MUTE] and [OK] for more than 
4sec.
“REMOTE 2” is indicated on the display.
∫To set the code to “REMOTE 1”
Press and hold [MUTE] and [4] for more than 
4sec.
“REMOTE 1” is indicated on the display.
One-Touch Connection 
(Connecting by NFC)
SC-HTB580P_RQT9922-Y.book  20 ページ  ２０１３年１２月１９日　木曜日　午前１１時０分