Panasonic Sc Htb550 Owners Manual

Getting started
RQT966011
Connect the speaker cables.
≥Use the “Panasonic” logo to identify the left and right speakers, then connect the cables (as illustrated).
≥Insert the wire fully, taking care not to insert beyond the wire insulation.
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥Leave at least 20 mm (25/32q) of space above and on each side of the speaker to allow enough space for fitting the 
speaker.
≥The position on the wall...

12RQT9660
Fit the speaker securely onto the screw(s).
≥For a safety measure to prevent the s peakers from falling, refer to page 17.
≥ To prevent damage or scratches, lay down a so ft cloth and perform the assembly on it.
Attach the front ornaments.
≥The two speakers are interchangeable.
≥ Keep the screws out of reach of children to prevent swallowing.
DODO NOT
≥Move the speaker so 
that the screw is in this 
position.≥In this position, the 
speaker will likely fall if 
moved to the left or right.
Place...

Getting started
RQT966013
Connect the speaker cables.
≥Insert the wire fully, taking care not to insert beyond the wire insulation.
Drive a screw into the wall.
≥Use the measurements indicated below to identify the screwing positions on the wall.
≥Leave at least 20 mm (25/32q) of space above and on each side of the speaker to allow enough space for fitting the 
speaker.
≥The position in the wall where the screw is to be attached as well as the screw should be capable of supporting over 33 kg 
(72.8...

14RQT9660
≥For a safety measure to prevent the speakers from falling, refer to page 17.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers 
horizontally” (>10).
Attach the stands. 
≥Use the “Panasonic” logo to identify the top and bottom of the speaker.
≥Keep the screws out of reach of children to prevent swallowing.
When placing the speakers on a table
Place the speakers using the stands
∏2...

Getting started
RQT966015
≥For a safety measure to prevent the speakers from falling, refer to page 17.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following steps 1 and 2 of “Place the speakers 
horizontally” (>10).
Attach the support legs and speaker feet.
≥Use the “Panasonic” logo to identify the top and bottom of the speaker.
≥Keep the screws and the speaker feet out of reach of children to prevent swallowing.
Place the speakers using...

16RQT9660
≥For a safety measure to prevent the speakers from falling, refer to page 17.
≥To prevent damage or scratches, lay down a soft cloth and perform the assembly on it.
Assemble the speakers following step 1 of “Place the speakers 
vertically” (>12).
Insert the speaker cable through the base.
≥Be sure to insert the speaker cable through the threading hole as indicated in the illustration. (If the speaker cable is 
twisted, it might not fit through the opening. Straighten the speaker cable before...

Getting started
RQT966017
Connect the speaker cables. 
≥Insert the wire fully, taking care not to insert beyond the wire insulation.
≥ Place the speaker that is connected with the speaker cable with a red connector on the observers’ right, and connect with 
the speaker cable with a white connector on the observers’ left.
To prevent the speakers from falling, it is recommended, as an additional 
protection measure, to attach the speakers to the wall or table with a fall 
prevention cord (hereafter...

18RQT9660
When placing the speakers on a table
Horizontal placement
Vertical placement
ACord§
BScrew eye≥Depending on the placement of the speakers, the 
screwing position of the screw eye may differ.
C Wall
D Approx. 150 mm (529/32q)
§  If the cord cannot be threaded through the holes, try bending the cord in 2 locations, about 
10 mm (
13/32q ) apart from the tip, at an angle of 45o (as illustrated above).






SC-HTB550_RQT9660-1P_mst.book  Page 18  Monday, March 5, 2012  11:03 AM 

Getting started
RQT966019
Step 3  Connections
≥Turn off all equipment before connection and read the appropriate owner’s manual.
Do not connect the AC power supply cord until all other connections are complete.
∫HDMI
The HDMI connection supports VIERA Link “HDAVI Control” (>25) when used with a compatible Panasonic TV.
≥Use the High Speed HDMI Cables. It is recommended that you use Panasonic’s HDMI cable.
Recommended part number (High Speed HDMI cable):
RP-CDHS15 (1.5 m/4.9 ft), RP-CDHS30 (3.0 m/9.8 ft),...

20RQT9660
You can direct the audio signal from the connected Blu-ray Disc playerTM, DVD player, Set Top Box, etc. 
to this system.
Preparation≥Connect the main unit to the TV (>19).
∫HDMI standby pass-through
Even if the main unit is in standby mode, the audio and/or video signal from the device connected to the BD/DVD or AUX1 
terminal will be sent to the TV connected to the HDMI OUT terminal (the sound will not be output from this system). When 
devices are connected to both BD/DVD and AUX1 terminals,...