Panasonic Sc Btt790 Operating Instructions

							Advanced 
operations 
41VQT3Z79
A Volume (Channel balance)
B Delay time for the Centre speaker
C Delay time for the Surround and Surround 
back speakers*
* Surround back speakers: optional ( >10)
∫ Adjusting speaker level
(Effective when playing multi-channel audio)1Select “Test” and press [OK].
A test signal is output.
2While listening to the test signal
Press [ 3,4] to adjust the volume of each 
speaker ( ). 
The volume can be adjusted between  r6 dB 
to  s6 dB.
≥ Set each speaker level according to the 
volume of the Front (L) and Front (R) 
speaker volume respectively.
3Press [OK].
The test signal stops.
∫ Delay time
For optimum listening with 5.1-channel sound, all 
the speakers, except for the subwoofer, should be 
the same distance from the seating position.
If either distance  1 or 2  is less than  3, measure 
the distance and adjust the time to make up for 
the difference (see the table below).
1  2  3: Primary listening distance
A Actual speaker position
B Ideal speaker position
1Press [ 3,4 ,2 ,1] to select the distance 
box ( ) and press [OK].
2Press [ 3,4 ] to select the setting and 
press [OK].
Delay time for the Centre speaker Subtract the distance  1 from  3
Delay time for the Surround and Surround 
back speakers Subtract the distance  2 from  3
To finish the speaker setting
Press [ 3,4 ,2, 1] to select “Complete” and 
press [OK].
Speaker settings
0
00
0.0
0.0ms
CompleteTe s t
LS R
L
RS
dB
dB
dB
msC
0dBSW



dB0
Distance (Approx.)Setting
34 cm1.0 ms
68 cm2.0 ms
102 cm3.0 ms
136 cm4.0 ms
170 cm5.0 ms
Distance (Approx.)Setting
170 cm5.0 ms
340 cm10.0 ms
510 cm15.0 ms
: 
: L
LS
R
SW
C
RS
C
RSLS
1
2
3
A
B
0.0ms
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  41 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							42VQT3Z79
Enjoying sound effects 
from all speakers
For more details on each setting, refer to “Sound 
Settings” on the Option menu. (> 34)
1 Press [SURROUND].
2 Press [ 3,4] to select “MULTI CH SOURCE” 
or “2CH SOURCE”, and then press [OK].
e.g.,
3 While the selected mode is displayed
Press [ 3,4 ] to select the desired setting. 
(>34)
∫ Adjusting speaker level during play
1 Press [CH SELECT] to activate the speaker 
setting mode.
2 Press [CH SELECT] several times to select 
the speaker.
≥Press [ 2,1 ] to adjust the balance of the 
front speakers.
3 Press [ 3] (increase) or [ 4] (decrease) to 
adjust the speaker level for each speaker.
s6 dB to  r6 dB
1 Press [SOUND].
2 Press [ 3,4 ] to select “2CH SOURCE” or 
“ALL SOURCE”, and then press [OK].
e.g.,
3 While the selected mode is displayed
Press [ 3,4] to select the desired setting and 
press [OK]. 
Repeat this procedure if necessary. ( >34)
	≥The sound effects/modes may not be available or have no 
effect with some sources.
≥ You may experience a reduction in sound quality when 
these sound effects/modes are used with some sources. If 
this occurs, turn the sound effects/modes off.
Speaker installation 
option
Consult a qualified building contractor when 
attaching the speakers to a wall. Improper 
attachment may result in damage to the wall and 
speakers and personal injury.
You can attach all of the speakers (except 
subwoofer) to a wall.
≥The wall or pillar on which the speakers are to 
be attached should be capable of supporting 
10 k g per screw.
1Drive a screw (not supplied) into the wall.
A At least 30 mm
B ‰ 4.0 mm
C ‰ 7.0 mm to
‰ 9.4 mm
D Wall or pillar
E 5.5 mm to 7.5 mm
2Fit the speaker securely onto the screw(s) 
with the hole(s).
Use the measurements indicated below to identify 
the screwing positions on the wall.
≥ Leave at least 20 mm of space above the 
speaker and 10 mm on each side to allow 
enough space for fitting the speaker.
Centre speaker
A 18 mm
B 25 mm
C 230.5 mm
Surround Effects
Sound Effects
Attaching to a wall
e.g.,  [BTT790]  Front speaker
DO NOTDO
≥In this position, the 
speaker will likely fall if 
moved to the left or right.≥Move the speaker so 
that the screw is in this 
position.

 




SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  42 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							Advanced 
operations 
43VQT3Z79
[BTT790]
Front speaker, Surround speaker
[BTT490]
Front speaker
Attach to a wall without the base and the stand.
D 51 mm
E 64 mm
F 350 mm
[BTT583]
Front speaker
Attach to a wall without the base. ( >11 )
G 45 mm
H 78 mm
[BTT583]  [BTT490]
Surround speaker
I 40 mm
J 24 mm Preventing from falling
[BTT790]
 Front speaker, Surround speaker
[BTT583]  [BTT490]  Front speaker
Preventing from dropping
Front speaker, Surround speaker, Centre speaker
1Thread a string to the speaker.
≥ Use a string of less than  ‰ 2.0 mm, which is 
capable of supporting over 10 k g.
e.g.,  [BTT790]  Front speaker
A String (not supplied)
B Rear of the speaker
2Thread a string from the wall to the 
speaker and tie tightly.
C Screw eye (not supplied)
D Wall
E Approx.150 mm
F Less than 100 mm



\b


Preventing the speakers from 
falling or dropping


 




When mounted on a wall
When placed on the floor
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  43 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							44VQT3Z79
It is possible to shorten the height of the front 
speaker and the surround speaker by directly 
connecting the speaker to the base without using 
the stand.
Preparation
Detach the speaker cable from the stand.
1Thread the detached cable through the 
base.
2Attach the speaker to the base and tighten 
the screw (supplied) securely.
3Connect the speaker cable to the speaker 
and to the terminal of the main unit. (>12)
∫ Reattaching the speaker cable to the 
stand
ReferenceTroubleshooting guide
Before requesting service, please perform the 
following checks.
If the problem remains unresolved, consult 
your dealer for instructions.
The following do not indicate a problem with 
this unit:
– Regular disc rotating sounds.
– Image disturbance during search.
– Image disturbance when replacing 3D discs.
∫Unit doesn’t respond to remote 
control or front panel buttons.
Press and hold [Í/I] on the main unit for 3 seconds.– If still unable to turn the unit off, disconnect the 
AC mains lead, wait 1 minute, then reconnect 
the AC mains lead.
∫ Cannot eject disc.
The unit may have a problem.1While the unit is off, press and hold [OK], the 
yellow button and the blue button on the remote 
control at the same time for more than 5 seconds.
j“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “06 FTO” is 
displayed on the unit’s display.
3 Press [OK] on the remote control or 
[< OPEN/CLOSE] on the unit.
To return to the factory preset.
¾ Select “Yes” in “Default Settings” in the Setup 
menu. ( >40)
To return all settings to the factory preset.
¾ Reset the unit as follows:
1While the unit is off, press and hold [OK], the 
yellow button and the blue button on the remote 
control at the same time for more than 5 seconds.
j“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “08 FIN” is 
displayed on the unit’s display.
3 Press and hold [OK] on the remote control or 
[< OPEN/CLOSE] on the unit for at least 
3 seconds.
[BTT790] [BTT490] Front and surround 
speaker assembly option
Straighten the 
cable and run 
through the stand. Pull out the 
cable through 
the hole.
Do you have the latest firmware installed?
Firmware updates may be released to correct 
operating irregularities that are discovered with 
certain movies. (
>19)
General operation
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  44 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							ReferenceAdvanced 
operations 
45VQT3Z79
This unit is turned off when the input for the 
TV is switched.
¾ This is a normal phenomenon when using 
VIERA Link (HDAVI Control 4 or later). For 
details please read the operating instructions 
for the TV.
The remote control doesn’t work properly.
¾Change the batteries in the remote control. 
(>8)
¾ The remote control and main unit are using 
different codes. If “SET  ” is displayed on the 
unit’s display when a button is pressed on the 
remote control, change the code on the 
remote control. ( >40, 49)
The TV tuner mode is not displayed when the 
TV is switched on.
¾
This phenomenon may occur, depending on the 
TV setting, when “Quick Start” is set to “On”.
¾ Depending on the TV, this phenomenon may 
be prevented by reconnec ting the HDMI cable 
to a different HDMI input terminal or by 
changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾ The ratings level returns to the factory preset.
1While the unit is on, press and hold [OK], the 
yellow button and the blue button on the remote 
control at the same time for more than 5 seconds.
j“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “03 VL” is 
displayed on the unit’s display.
3 Press [OK] on the remote control or 
[< OPEN/CLOSE] on the unit.
This unit does not recognize the USB 
connection correctly.
¾ Disconnect and reconnect the USB cable. If it 
still does not recognize the connection, turn 
this unit off and on again.
¾ USB devices may not be recognized by this 
unit when connected using the following :
ja USB hub
ja USB extension cable other than the 
supplied with the Wireless LAN Adaptor 
DY-WL5 (optional)
¾ If you connect USB HDD to this unit, use the 
USB cable that is supplied with the HDD.
The unit switches to standby mode.
¾This unit will automatically turn to standby 
mode after 30 minutes if it is inactive. ( >21)
¾
When the time set for the sleep timer has 
passed, the main unit will be turned off. (>8)
¾One of the unit’s safety devices is activated. 
Press [Í/I] on the main unit to turn the unit on.
The unit does not turn off.
1 Press and hold [ Í/I] on the main unit for 5 
seconds. (If still unable to turn the unit off, 
disconnect the AC mains lead, wait 1 minute, 
then reconnect the AC mains lead.)
2 Reset the unit as follows:
While the unit is off, press and hold 
[+ VOLUME], [ 36)
jWhen Dolby Digital Plus, Dolby TrueHD,  and DTS-HD audio are not output in 
bitstream, select “Yes” in “Default Settings” 
and make proper settings. ( >40)
¾ The unit and television are using different 
video systems.
1 While the unit is on, press and hold [OK], the 
yellow button and the blue button on the 
remote control at the same time for more than 
5 seconds.
–“00 RET” is displayed on the unit’s display.
2 Repeatedly press [ 1] (right) on the remote 
control or [ Í/I] on the unit until “05 P/N” is 
displayed on the unit’s display.
(Continued on the next page)
Picture
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  45 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							46VQT3Z79
3Press and hold [OK] on the remote control or 
[< OPEN/CLOSE] on the unit for at least 
3 seconds.
The system switches from PAL to 
NTSC or 
vice versa.
¾ The system used on the disc doesn’t match 
your television.
jPAL discs cannot be correctly viewed on an  NTSC television.
jThis unit can convert NTSC signals to 
PAL60 for viewing on a PAL television 
(> 36, “NTSC Contents Output”).
¾ When “3D BD-Video Playback” in the Setup 
menu is set to “Automatic”, images may not 
be output depending on the connection 
method. After removing the disc from this unit, 
select “Set before play” in the Setup menu, 
and select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >37)
¾ If irregular colouring occurs on your TV, turn 
the TV off for about 30 minutes.
If it persists, move the speakers further away 
from the TV.
Video is not output.
¾Set “High Clarity Sound” in the Setup menu to 
“Disable” to use the VIDEO OUT terminal. (>37)
Video is not output in high-definition.
¾Confirm that “HDMI Video Format” in the 
Setup menu is set properly. ( >36)
3D video is not output.
¾ Change the settings as required by the 
connected TV format. ( >37, “3D Type”)
¾ Are the settings on this unit and the TV 
correct? ( >24)
¾ Depending on the connected TV, the video 
being played back might switch to 2D video 
due to changes in resolution etc. Check the 
3D setting on the TV.
¾ Check that proper HDMI video input is 
selected on the TV.
3D video is not output correctly as 2D.
¾Select “Set before play” in the Setup menu, 
and select “2D Playback” in the setup screen 
displayed when playing 3D discs. ( >37, “3D 
BD-Video Playback”)
¾ Discs that have recorded titles with Side by 
side (2 screen structure) and that can be 
enjoyed in 3D are played back in accordance 
with the settings of the TV.
A black band is displayed around the edge of 
the screen.
The aspect ratio of the screen is abnormal.
¾
Confirm the “TV Aspect” is set properly. (>39)¾Adjust the aspect setting on the television.
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
¾Check connections to speakers and other 
equipment. ( >11s17)
¾ Ensure the speaker settings for your 
speakers are correct. ( >41)
¾ To output audio from a device connected with 
an HDMI cable, set “HDMI Audio Output” to 
“On” in the Setup menu. ( >37)
¾ When “BD-Video Secondary Audio” is set to 
“On”, Dolby TrueHD, Dolby Digital Plus, 
DTS-HD Master Audio and DTS-HD High 
Resolution Audio are output as Dolby Digital 
or DTS Digital Surround.
¾ Re-master will not work when the bitstream 
signal is output from the HDMI AV OUT 
terminal. ( >34)
¾ Depending on the connected equipment, the 
sound may be distorted if this unit is 
connected with an HDMI cable.
¾ The multi-channel audio from a device 
connected to the TV is not output in it’s 
original multi-channel form.
jIf the device has an optical audio output 
terminal, connect the device to this unit’s 
DIGITAL AUDIO IN terminal. ( >15)
No surround sound.
¾ Press [SURROUND] to select a surround 
effect. ( >42)
¾ [BTT790]
Ensure that the surround selector switch of 
the wireless system is set in the centre 
position. Then, turn the wireless system off 
and then back on.
¾ (When using the 7.1ch speaker system)
Audio is not available from the surround back 
speakers (optional) even though Dolby Pro 
Logic II turns on.
Sound
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  46 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							Reference
47VQT3Z79
Cannot switch audio.
¾When audio is output from the HDMI AV OUT 
terminal, set “Dolby D/Dolby D +/Dolby 
TrueHD”, “DTS/DTS-HD” or “MPEG Audio” to 
“PCM”. ( >36)
No sound from the TV.
¾ Press [EXT-IN] to select the corresponding 
source. ( >20)
¾ When connecting the unit to a TV using an 
HDMI cable, check whether the HDMI 
terminal on the TV is labelled “HDMI (ARC)”. 
If not labelled in this way, connect using the 
HDMI cable in combination with an optical 
digital audio cable. ( >13)
¾ If there is no sound from the equipment 
connected to this unit’s DIGITAL AUDIO IN 
terminal, please make sure that the optical 
audio output of the equipment is set to PCM.
Disc cannot be played.
¾The disc is dirty. ( >5)
Still pictures (JPEG) do not play back 
normally.
¾ The images that were edited on the PC, such 
as Progressive JPEG, etc., may not be played 
back.
I can’t play back BD-Live.
¾The SD card is write-protected. ( >7)
¾ Confirm that this unit is connected to the 
broadband Internet. ( >16)
¾ Confirm the “BD-Live Internet Access” 
settings. ( >39)
¾ Confirm an SD card is inserted into the SD 
card slot. ( >20)
Alternative soundtrack and subtitles cannot 
be selected.
¾ The languages are not recorded on the disc.
¾ You may not be able to use the Option menu 
to change the soundtrack and subtitles on 
some discs. Use the disc’s menus to make 
changes. ( >24)
Cannot charge or operate.
¾ Check that the iPod/ iPhone is connected 
firmly. ( >26)
¾ The battery of the iPod/iPhone is depleted. 
Charge the iPod/iPhone, and then operate 
again.
¾ When unexpected operation occurs while 
using the iPod/iPhone, connect the iPod/
iPhone again or try to restart the iPod/iPhone.
Cannot display iPod/iPhone videos/photos on 
the TV.
¾Make sure that TV is connected to the VIDEO 
OUT terminal on this unit. ( >14)
¾ Operate the iPod/iPhone menu to make the 
appropriate video/photo output settings for 
your TV. (Refer to operating instructions for 
your iPod/iPhone.)
The TV input channel unintentionally changes 
to HDMI input.
¾When the main unit is connected with an 
“HDAVI Control” compatible TV and VIDEO 
IN is selected for iPod/iPhone video or photo 
playback, the TV input channel will 
automatically change to the HDMI input 
channel when [HOME] is pressed.
jRe-select the TV’s VIDEO IN input channel.
Distorted sound or noise is heard.
¾ Adjust the position of the antenna.
A beat sound is heard.
¾Try to keep a certain amount of distance 
between the antenna and the TV.
Noise is excessive.
¾Change the audio to be output as monaural.
Press [AUDIO] to select “MONO”.
The sound becomes monaural.
≥To cancel, press the button again or change 
the frequency.
In normal circumstances, select “AUTO STEREO”.
Playback
iPod/iPhone operation
Radio
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  47 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							48VQT3Z79
The wireless link indicator is flashing.
¾There is no link between the main unit and the 
wireless system. Turn the wireless system off 
and then back on. Alternatively, turn the 
wireless system off, disconnect the AC mains 
lead and then reconnect it.
The wireless link indicator does not light.
¾Check that the main unit is turned on, and the 
wireless system is turned on.
¾ Ensure that the digital transmitter is fully 
inserted into the slot of the main unit. ( >15)
The wireless link indicator keeps flashing 
between red and green.
¾ There is a power supply problem. Consult the 
dealer.
I can’t connect to the network.
¾Confirm the network connection and settings. 
(>16, 18, 38)
¾ Check the operating instructions for each 
device and connect accordingly.
When using wireless LAN connection, video 
from the DLNA Certified media server is not 
played back or video frames are dropped 
during playback.
¾Higher transfer rate router such as 802.11n 
(2.4 GHz) wireless router may solve the 
problem. If you use 802.11n (2.4 GHz) 
wireless router, it is necessary to set the 
encryption type to “AES”.
Simultaneous use with a microwave, cordless 
telephone etc. at 2.4 GHz may result in 
connection interruptions  or other problems.
Messages
The following messages or service numbers may 
appear on the TV or unit’s display.
Cannot play.
¾You inserted an incompatible disc.
Cannot play on this unit.
¾You tried to play a non-compatible image.
¾ Confirm “SD” on the unit’s display is not 
displayed and re-insert the card.
No disc inserted.
¾The disc may be upside down.
$ This operation is not available.
¾ Some operations are uns upported by the unit. 
For example; jBD-Video: During playback, reverse 
slow-motion or reverse frame-by-frame is 
not possible.
IP address is not set.
¾ The “IP Address” in “IP Address / DNS 
Settings” is “---. ---. ---. ---”. Set the “IP 
Address”, “Subnet Mask”, and “Gateway 
Address”. (Select the automatic address 
acquisition if necessary.)
The wireless access point currently has a low 
network security setting. It is recommended to 
change to a higher setting.
¾Authentication type for the wireless LAN is set 
to “Open system”, or the encryption type is 
set to “No encryption”. It is recommended to 
encrypt for safety reasons. For details, refer 
to the instructions of the wireless router being 
used. Encryption is required when playing 
back video, etc., from DLNA compatible 
devices.
No Video
¾Depending on the connected iPod/iPhone, 
video menu may not be available on the TV. 
Select “ALL” on the unit’s display and operate 
video playback from y our iPod/iPhone menu. 
(> 26)
[BTT790] Wireless system 
(SH-FX71)
Network
¾ On the “Wireless Settings” screen ( >38), the 
continuous lighting of at least 4 “Reception” 
indicators is the target for a stable 
connection. If 3 or fewer indicators are lit or 
the connection is being interrupted, change 
the position or angle of your wireless router 
and see if the connection state improves. If 
there is no improvement, connect to a wired 
network and perform the “Easy Network 
Setting” ( >18) again.
On the television
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  48 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							Reference
49VQT3Z79
F99
¾The unit fails to operate properly. Press [ Í/I] 
on the main unit for 3 seconds to switch the 
unit to standby, then switch back on.
HDMI ONLY
¾ Some BD-Video discs can only be output with 
HDMI.
NET
¾While connecting to a network.
No PLAY
¾There is a viewing restriction on a BD-Video 
or DVD-Video. ( >39)
No READ
¾ The media is dirty or badly scratched. The 
unit cannot play.
PLEASE WAIT
¾The unit is carrying out internal process. This 
is not a malfunction. You cannot operate the 
unit while “PLEASE WAIT” is displayed.
REMOVE
¾The USB device is drawing too much power. 
Remove the USB device.
SET  
(“  ” stands for a number.)
¾ The remote control and main unit are using 
different codes. Change the code on the 
remote control.
Press and hold [OK] 
and the indicated 
number button at the 
same time for more 
than 5 seconds.
U59
¾The unit is hot.
The unit switches to standby for safety 
reasons. Wait for about 30 minutes until the 
message disappears.
Select a position with good ventilation when 
installing the unit.
H or F 
(“    ” stands for a number.)
¾ Check and correct the speaker cable 
connections.
¾ There is something unusual.
¾ Check the unit using the troubleshooting 
guide. If the service number remains 
displayed, do the following.
If the service number remains displayed despite 
doing the above, request service from the dealer. 
Inform the dealer of the service number when 
requesting service.
IPOD OVER CURRENT ERROR
¾ The iPod/iPhone is drawing too much power. 
Remove the iPod/iPhone, and turn the unit off 
and on again.
START
¾The system is being restarted during the 
firmware update. Please do not turn off the unit.
UPD /
(“    ” stands for a number.)
¾ The firmware is being updated. Please do not 
turn off the unit.
FINISH
¾The firmware update is complete.
NOT CONDITIONAL
¾The requested operation cannot be 
conducted.
SET OK
¾The stations are set, and the radio tunes to 
the last preset station.
ERROR
¾Automatic presetting is unsuccessful. Preset 
the stations manually.
TUNED/STEREO
¾Stereo broadcasting or  stereo sound is 
selected.
TUNED
¾ Monaural broadcasting or  monaural sound is 
selected.
On the unit’s display
1 Disconnect the plug from the household 
mains socket, wait a few seconds, then 
reconnect it.
2 Press [ Í/I] to turn the unit on.
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  49 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分
 
						

							50VQT3Z79
Specifications
* The impedance of all the speakers is 3≠.
GENERAL
Power consumption:89 W
Power consumption in 
standby mode: Approx. 0.1 W
Power supply
[For[Australia[and[New[Zealand]: AC 220 V to 240 V, 50 Hz
[Except[Australia[and[New[Zealand]:AC 110 V to 127 V, 
AC 220 V to 240 V, 50 Hz/60 Hz
iPod/iPhone Connector: DC OUT 5 V 1.0 A MAX
Dimensions (W kHk D):
[BTT790]430 mm k 40 mm k 279 mm
[BTT583] [BTT490]430 mm k 38 mm k 279 mm
Mass:
[BTT790]Approx. 3.0 k g
[BTT583] [BTT490]Approx. 2.7 kg
Operating temperature 
range: 0oC to 40 oC
Operating humidity range: 35 % to 80 % RH 
(no condensation)
AMPLIFIER SECTION
RMS TTL POWER OUTPUT:1000 W (with WIRELESS 
SYSTEM)
1 kHz, 10 % total harmonic distortion FRONT: 185 W per ch (3≠)
CENTRE: 180 W per ch (3≠)
[BTT583] [BTT490]SURROUND: 125 W per ch (3
≠)
100 Hz, 10 % total harmonic distortion SUBWOOFER: 200 W per ch (3≠)
Audio Input AUX  k1
Digital Audio Input Optical  k1
HDMI AV input  k2
Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
Audio Format: PCM, Dolby Digital, DTS
FM TUNER SECTION
Frequency range:87.50 MHz to 108.00 MHz (50 kHz 
step)
Antenna terminals:75≠ (unbalanced)
SPEAKER SECTION
WooferCONE TYPE (cm)
Full rangeCONE TYPE (cm)
Tw e e t e rSEMI-DOME 
TYPE (cm)
[BTT790]
Front j6.5j
Centre6.5 6.5j
Surround j6.5j
Subwoofer16jj
[BTT583]
Front8j2.5
Centre6.5 6.5j
Surround j6.5j
Subwoofer16jj
[BTT490]
Front j6.5j
Centre6.5 6.5j
Surround j6.5j
Subwoofer16jj
Dimensions(W (mm)kH (mm)kD (mm))Mass(Approx. kg)
[BTT790]
Front 292 k1185  k292 2.6
Centre 280 k84  k78 0.91
Surround 292 k1185  k292 2.6
Subwoofer 180 k408  k300 4.3
[BTT583]
Front 127 k403  k121 1.05
Centre 280 k84  k78 0.91
Surround 80 k139  k 70 0.47
Subwoofer 180 k408  k300 4.3
[BTT490]
Front 292 k1185  k292 2.6
Centre 280 k84  k78 0.91
Surround 80 k139  k 70 0.47
Subwoofer 180 k408  k300 4.3
TERMINAL SECTION
USB slot: USB2.0: 2 system
SD card slot: Connector: 1 system
Ethernet: 10BASE-T/100BASE-TX 1 system
[For[Australia[and[New[Zealand]
Wireless LAN:
Standard Compliance: IEEE802.11 b/g/nFrequency range:  2.4 GHz band
Security:  WPATM/WPA2TM (Encryption 
Type: TKIP/AES, Authentication Type: 
PSK), WEP (64 bit/128 bit)
SC-BTT790&583&490GNGSGA-VQT3Z79_mst.book  50 ページ  ２０１２年１月１９日　木曜日　午前１０時３４分