Panasonic Sc Bft800 Operating Instructions

							Getting started 
11
VQT2Z56
∫Discs that cannot be played in this unit
Any other disc that is not specifically supported or 
previously described.
≥2.6 GB and 5.2 GB DVD-RAM
≥ DVD-RAM that cannot be removed from cartridge
≥ Super Audio CD
≥ Photo CD
≥ DVD-Audio
≥ Video CD and Super Video CD
≥ WMA discs
≥ HD DVD
∫ Region management information
BD-Video
This unit plays BD-Video marked with labels containing the 
region code “ B”.
Example:
DVD-Video
[For[the[United[Kingdom[and[Republic[of[Ireland[
This unit plays DVD-Video marked with labels containing the 
region number “ 2” or “ALL ”.
Example:
[For[Australia[and[New[Zealand]
This unit plays DVD-Video marked with labels containing the 
region number “ 4” or “ALL ”.
Example:
∫ Finalize
DVD-R/RW/R DL, +R/+RW/+R DL and CD-R/RW recorded by 
a recorder, etc. needs to be finalized by the recorder to play on 
this unit. Please refer to the recorder ’s instructions.
∫BD-Video
≥3D videos can be played back when this unit is connected to 
a 3D compatible TV using a High Speed HDMI Cable.
≥ This unit supports high bit rate audio (Dolby Digital Plus, 
Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD 
Master Audio) adopted in BD-Video. In order to enjoy these 
audio formats, refer to page 39.
∫ Music CD
Operation and sound quality of CDs that do not conform to 
CD-DA specifications (copy control CDs, etc.) cannot be 
guaranteed.
∫SD card
≥miniSD Cards, microSD Cards, microSDHC 
Cards and microSDXC Cards can be used, but 
must be used with an adaptor card. These are 
usually supplied with such cards, or otherwise 
customer provided.
≥ Keep the Memory Card out of reach of children to 
prevent swallowing.
≥ To protect the card’s contents, move the record prevention 
tab (on the SD card) to “LOCK”.
≥ This unit is compatible with SD Memory Cards that meet SD 
Card Specifications FAT12 and FAT16 formats, as well as 
SDHC Memory Cards in FAT32 format (Does not support 
long file name.) and SDXC Memory Cards in exFAT.
≥ If the SD card is used with incompatible computers or 
devices, recorded contents may be erased due to the card 
being formatted etc.
≥ Useable memory may be slightly less than the card capacity.
∫ USB device
≥This unit does not guarantee connection with all USB 
devices.
≥ This unit does not support USB device charging.
≥ FAT12, FAT16 and FAT32 file systems are supported.
≥ This unit supports USB 2.0 High Speed.
	≥ It may not be possible to play the above media in some cases due to the type of media, the condition of the recording, the recording method and how the files 
were created.
≥ The producers of the disc can control how discs are played. So you may not always be able to control play as described in these operating instructions. Read 
the disc’s instructions carefully.
2
4
1ALL2
4ALL3
4
2
SCBFT800_VQT2Z56_eng.book  11 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							12
VQT2Z56
STEP 1: Placement
How you place the main unit and the active subwoofer can affect the bass and the sound field.
Place the main unit near the TV.
The main unit should be placed parallel to the seating position.
e.g.
*1 Place the main unit on a flat secure base.
*2 Secure the main unit to prevent it from falling.
*3 Do not place the main unit in front of a 3D compatible TV. The unit may block the transmitter for the 3D eyewear. 
*4 Do not place the main unit too close to the TV. The unit may interfere with the TV’s various sensors (ambient light, etc.).
	≥You can damage the speakers and shorten their useful life if you play sound at high levels over extended periods.
≥ Placing the main unit too close to the floor, walls, and corners can result in excessive bass. Cover walls and windows with thick curtains.
≥ Do not use the active subwoofer or this unit in a metal cabinet or bookshelf.
≥ Remove the wall mount brackets from the main unit when using to place this unit.
Place to the right or left of the TV, on the floor or on a 
sturdy shelf so that it will not cause vibration. Leave about 
30 cm from the TV.
To avoid interference, maintain the following distances 
between the active subwoofer and other electronic 
devices that use the same radio frequency (2.4 GHz band). The active subwoofer will automatically seek a clear channel if 
any of these other devices interfere with its communication.
When this happens there is a brief interruption to the audio 
coming from the subwoofer.
This is the normal operation of the product working to assure 
the best possible performance of your home theatre audio 
system.
If the interference persists, try moving the other devices to 
another location outside the range of the active subwoofer or 
move the active subwoofer nearer to this unit.
≥
Place the active subwoofer within approximately 10 m of this unit, and in a 
horizontal position with the top panel faced upward.
≥ To allow for proper ventilation and to maintain good airflow around the 
active subwoofer, position it with at least 5 cm of space on all sides.
Caution
≥The main unit and the active subwoofer are to be used only as indicated in this setup. Failure to do so may 
lead to damage to the amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified 
service person if damage has occurred or if you experience a sudden change in performance.
≥ Do not attempt to attach the main unit to a wall using methods other than those described in this manual.
The main unit
The active subwoofer
On the wall*2On a table*1, 2, 3, 4
e.g.,
Wireless router, etc.:
approx. 2 m
Cordless phone and 
other electronic devices:
approx. 2 m
Active subwoofer
SCBFT800_VQT2Z56_eng.book  12 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							Getting started 
13
VQT2Z56
Never use any other method than spacified to install.
Preparation
≥To prevent damage or scratches, lay down a soft cloth and perform the 
assembly on it.
≥ Keep the screws out of reach of children to prevent swallowing.
1At the bottom of the main unit:
Detach the stand after removing the screws.
2On the rear of the main unit:
Place the wall mount bracket by aligning 
the holes in the wall mount bracket with the 
projecting parts  A.
3Screw the wall mount bracket firmly into 
place.
≥ Screw tightening torque: 100 N 0cm to 120 N 0cm.
≥ Repeat the steps above when installing the second wall mount 
bracket.
4Complete all the necessary connections to 
this unit. 
≥Connect the AC mains lead to this unit, but do not connect it to the 
household mains socket until the installation is completed.
5Use the measurements indicated below to 
identify the screwing positions on the wall.
≥Position the unit with at least 100 mm of space above the unit and 
100 mm on either side of the unit. If not, it will not be possible to attach 
the unit to the wall.
≥ Be sure that there is enough space above the unit and that the screw 
hole positions are level with each other before drilling into the wall.
≥ Be sure to use a spirit level to ensure that both screwing positions are 
horizontal to each other.
6Check the strength of the installation 
location.
≥Check the wall strength at the 2 screwing positions. If the strength at 
any of these positions is lacking, provide sufficient reinforcement.
– The position in the wall where the screw is to be attached should be 
capable of supporting over 20 k g.
7Drive 2 screws (not supplied) into the 
screwing positions identified in step 5.
≥ Take care when fixing this unit to the wall. Always ensure that there 
are no electrical cables or pipes in the wall before hanging this unit.
≥ Be sure to use commercially available screws with nominal diameter 
of  ‰4.0 mm suited to the wall surface material (wood, steel frame, 
concrete, etc.) and also capable of supporting over 20 k g each for 
attaching this unit to the wall.
≥ Improper attachment may result in damage to the wall and this unit.
8Mount the unit securely onto the screws.
≥Be sure that both the wall mount brackets are securely attached to the 
screws.
≥ If this unit is tilting forward, remove this unit from the screws and 
adjust by tightening the screws.
9Attach the cord to a wall with a screw (not 
supplied).
≥Check the strength of the installation location. If the strength at any of 
these positions is lacking, provide sufficient reinforcement.
Attaching the main unit to a wall
To attach this unit to the wall, refer to the following instructions.
Installation work should never be done by any other than a qualified installation specialist.




A 62 mm
B 126 mm
C 103 mm D
803 mm
E 128.5 mm

 

A
At least 30 mm
B ‰ 4.0 mm
C ‰ 7.8 mm to ‰  9.4 mm
D Wa ll
E 4.5 mm to 5.5 mm


AMove the main unit so that the screw is in this position.
B Wal l
 

A
Rear of the main unit
B Fall prevention cord (not supplied)
C Screw eye (not supplied)
SCBFT800_VQT2Z56_eng.book  13 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							14
VQT2Z56
STEP 2: Connections
Turn off all equipment before connection and read the appropriate operating instructions.
Do not connect the AC mains lead until all other connections are complete.
≥This system supports the PCM and the Dolby Digital bitstream input audio. However, for example the system does not support 
the DTS bitstream input audio.
	
≥ Do not make the video connections through the VCR.
Due to copy guard protection, the picture may not be 
displayed properly.
≥ Turn off all equipment before connection.
∫ OPTICAL IN
≥After making the digital audio connection, make settings to 
suit the type of audio from your digital equipment ( >31).
∫ HDMI
The HDMI connection supports VIERA Link “HDAVI Control” 
(> 31) when used with a compatible Panasonic TV. ≥
Please use High Speed HDMI Cables that have the HDMI 
logo (as shown on the cover). It is recommended that you 
use Panasonic’s HDMI cable. When outputting 1080p signal, 
please use HDMI cables 5.0 meters or less.
Recommended part number (High Speed HDMI Cable):
RP-CDHS15 (1.5 m), RP-CDHS30 (3.0 m), 
RP-CDHS50 (5.0 m), etc.
≥ Audio will be output through the system’s speakers when 
“Off” is selected in “HDMI Audio Output”. ( >40)
Connection to a TV
Basic connection
OPTICAL
OUT
L
VIDEO IN
R 
AUDIO IN

VIDEO OUT
OPTICAL
TV
A
Video cable  (not supplied)
B Optical digital audio cable  (not supplied)
To enjoy TV audio from this home theatre 
system’s speakers
1 Connect the TV and the main unit with the 
Optical digital audio cable (not supplied). 
2 Select “DIGITAL IN ” or “D-IN” as a source  (> 23).
AV1
VIDEO IN


If the TV does not have a VIDEO IN terminal, connect using 
a Scart adaptor (Scart—VIDEO IN).
A Scart adaptor  (not supplied)
B Video cable  (not supplied)
[For[the[United[Kingdom[and[Republic[of[Ireland[
e.g.,
SCBFT800_VQT2Z56_eng.book  14 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							Getting started 
15
VQT2Z56
≥It is possible to playback 3D videos by connecting this unit with a 3D compatible TV.
ARC (Audio Return Channel)
(Available when using an ARC compatible TV)
With this function it is possible to receive the digital audio signal from the TV without connecting the optical digital audio cable (B). 
Be sure to connect to the TV’s ARC compatible terminal.
≥ Select “ARC” as the audio input source ( >23).
≥ Refer to the operating instructions of the TV for the settings to output digital audio.
Connection for the best picture and audio
OPTICAL
OUTAV IN
 HDMI AV OUT (ARC)
OPTICAL
TV
A
HDMI cable (not supplied)
B Optical digital audio cable  (not supplied)
To enjoy TV audio from this home theatre 
system’s speakers
1 Connect the TV and the main unit with the 
Optical digital audio cable (not supplied).
2 Select “DIGITAL IN” or “D-IN” as a source 
(> 23).
Connection with Set Top Box, etc.
OPTICAL
OUT


OPTICAL
TV Refer to the operating instructions of the respective 
devices for the optimal connections.
A
Optical digital audio cable  (not supplied)
B Set Top Box (Cable/Satellite), etc.
To enjoy TV audio from this home theatre 
system’s speakers
1 Connect the STB and the main unit with the 
Optical digital audio cable (not supplied). 
2 Select “DIGITAL IN” or “D-IN” as a source  (> 23).e.g.,
SCBFT800_VQT2Z56_eng.book  15 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							16
VQT2Z56
Use outdoor antenna if FM radio reception is poor.
Radio antenna connection
Using an indoor antenna
Using an outdoor antenna

Main unit
AFM indoor antenna  (supplied)
B Adhesive  tap e
Affix this end of the antenna where reception is best.
Digital transmitter connection

 Main unit AFM outdoor antenna  [Using a TV antenna (not supplied)]
The antenna should be installed by a competent technician.
B 75 ≠ coaxial cable  (not supplied)
C Antenna plug adaptor  (United Kingdom and Republic of Ireland 
only)
≥ Keep the adaptor out of reach of children to prevent swallowing.
e.g.,
Insert fully until you 
hear a click.
Do not insert or remove while the home theatre unit is on.
Make sure that the digital transmitter is fully inserted.
If the digital transmitter is not fully inserted, the sound may 
not be available from the active subwoofer. DO
DO NOT
Rear of the main unit
SCBFT800_VQT2Z56_eng.book  16 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							Getting started 
17
VQT2Z56
The following services can be used when this unit is connected 
to broadband.
≥Firmware can be updated  (>21)
≥ You can enjoy the BD-Live ( >26)
≥ You can enjoy the VIERA CAST ( >35)
≥ DLNA feature ( >36) For details about connection method, refer to the instructions 
supplied with the connected equipment.
Connection to a broadband network
∫
Using LAN (ethernet) cable ∫Using Wireless LAN Adaptor DY-WL10 
(optional)
A LAN Cable [Straight]
(not supplied)
B Broadband router, etc.
C Internet A
Wireless LAN Adaptor
B Wireless router (Access point), etc.
C Internet
≥ Use shielded LAN cables when connecting to peripheral 
devices.
≥ Inserting any cable other than a LAN cable in the LAN 
terminal can damage the unit. ≥
Only the Wireless LAN Adaptor DY-WL10 (optional) can 
be used.
≥ Read the operating instructions for the Wireless LAN 
Adaptor DY-WL10 (optional) thoroughly when using it.
≥ For up to date compatibility information on your Wireless 
router (Access Point) refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
≥ The unit is not compatible with public wireless LAN 
services (Hotspot etc.) provided in airports, stations, cafes 
etc.



DC OUT5VLAN
WIRELESS500mA MAX



SCBFT800_VQT2Z56_eng.book  17 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							18
VQT2Z56
STEP 3: AC mains lead connection
AAC mains lead  (supplied)
B To a household mains socket A
AC mains lead  (supplied)
B To a household mains socket
≥ Connect only after all other connections are complete.
≥ The main unit consumes a small amount of AC power, even when it is turned off (When the “Quick Start” setting is “Off”: approx.  
0.1 W, the active subwoofer: approx. 0.4 W). In the interest of power conservation, if you will not be using this unit for a lon g 
time, unplug it from the household mains socket.
≥ Do not use any other AC mains lead except the supplied one.
STEP 4:
Active subwoofer wireless connection
Turn on the active subwoofer after all connections are complete.
∫ When “  [W] ” is not displayed on the main unit’s display (Making the active subwoofer link)
If you should change the digital transmitter, repeat the pairing 
steps using the new digital transmitter.
Preparation
≥Make sure to connect the AC mains lead of the active 
subwoofer.
≥ Insert the digital transmitter into the main unit.
≥ Turn on the main unit and reduce the volume.
1 Turn on the active subwoofer.
2 While pressing [ ∫] on the main unit, press the number 
button [2] on the remote control until “P” lights in the main 
unit’s display. 3
While “P” is displayed, press [I/D SET] on the bottom of the 
active subwoofer.
≥The indicator on the active subwoofer turns green.
≥ If “P” goes off before you press [I/D SET], repeat step  2 
and then continue the procedure.
4 While pressing [ ∫] on the main unit, press the number 
button [2] on the remote control.
5 Turn off and on the active subwoofer.
≥Make sure the indicator on the active subwoofer lights up 
green. (“ [W] ” is also displayed on the main unit’s 
display.)
\For\the\United\Kingdom\and\Republic\of\Ireland\only\
BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 3 BEFORE CONNECTION.




Main unit Rear of the active subwoofer
≥
AC mains lead with a ferrite 
core is for the active 
subwoofer. Do not use any 
other AC mains lead except 
the supplied one.
WIRELESS LINK indicator
Red:  The active subwoofer is on and the wireless link is deactivated.
Green:  The active subwoofer is on and the wireless link is activated.
(“  [W]  ” is also displayed on the main unit’s display.)
Press [ CI,BÍ ] on the active subwoofer.
Unit on/off button [ CI,BÍ ]
C I:  The active subwoofer is on.
BÍ : The active subwoofer is off.
Active subwoofer
AUse a pointed object.
0ê0Ð0å0Á0ô0æ0õ

SCBFT800_VQT2Z56_eng.book  18 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							Getting started 
19
VQT2Z56
STEP 5: Easy setup
The Easy setup assists you to make necessary 
settings.
Follow the on-screen prompts to make basic settings for the 
system.
Preparation
≥Turn on your TV and select the appropriate video input mode 
(e.g., VIDEO 1, AV 1, HDMI, etc.) to suit the connections to 
this unit.
≥ Confirm the digital transmitter connection. ( >16)
1Press [ Í] to turn on this unit.
2Press [ CI,BÍ ] on the active subwoofer 
to turn it on.
≥ Make sure the wireless link indicator lights green. ( >18 )
3Follow the on-screen instructions and 
make the settings with [ 3,4 ,2 ,1 ] and 
press [OK].
Language
Select the language used on menu screen.
TV Aspect Select the aspect to suit your TV and preference.
Speaker check Check if the connection to each speaker is valid.
TV Audio Select the audio input connection from your TV,
[item with “(TV)”].
Quick Start Speed of startup from standby mode is increased.
4Press [OK] several times to finish the “Easy 
setup”.
After completing “Easy setup”, you can perform “Network Easy 
Setting”.
	≥You can perform this setup anytime by selecting “Easy setup” in the Setup 
men u. ( >41)
≥ Language and TV Aspect settings are automatically retrieved if this unit is 
connected to a Panasonic TV (VIERA) supporting HDAVI Control 2 or later 
via an HDMI cable.
When “BD/DVD” is selected as the source
Select “Wired” or “Wireless” and press [OK].
∫ “Wired” connection
Follow the on-screen instructions to make your connection settings.
≥When you experience problems ( >20)
∫ “Wireless” connection
If you select “Wireless” and “Wireless LAN Adaptor is not 
connected.” is displayed, check that the Wireless LAN Adaptor is 
fully inserted. Alternatively, disconnect and reconnect it. If there is 
still no c hange in the display, consult your dealer for advice.
Select “WPS (PUSH button)” or “Search for 
access point” and then follow the on-screen 
instructions and make the settings.
WPS (PUSH button):
If your Wireless router (Access point) 
supports WPS (PUSH button), you can 
easily perform the settings by pressing 
WPS button on it.
WPS (Wi-Fi Protected Setup) is a 
standard that facilitates settings relating 
to the connection and security of 
wireless LAN devices.
1Press WPS button or corresponding button of Wireless 
router (Access point) until the lamp starts flashing.
≥For details, refer to the operating instruction of Wireless 
router (Access point).
2 Press [OK].
Search for access point:
Available Wireless routers (Access points) are searched and 
listed. You can select the one to use from the list.
1 Press [ 3,4] to select SSID*
2 of Wireless router (Access 
point) you want to connect with. Then press [OPTION] to 
show information of the selected router, make a note of the 
authentication and encryption type.
(Continued on the next page)
OKOK
Network Easy Setting
OKRETURN
Network Easy Setting (Connection Test)
Wired
Wireless
Select a connection mode. 
 Current setting  :  Wired
 
LAN cable connection:
 Connect a LAN cable to the unit and select “Wired”.
Wireless LAN connection:
 Connect the Wireless LAN Adaptor (DY-WL10) to the USB
 port and select “Wireless”.
Access Point Connection SettingSelect a connection method for access to 
Wireless LAN.
Please refer to the operating instructions of 
the access point about connection methods.
WPS (PUSH button)
Search for access point
1
e.g.,
OK
Access Point Connection Setting
ReceptionSelect an access point to connect with.
To search for access point again, please 
select Search again below.
SSIDXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXSearch again
SSID
Wireless type
Authentication type
Encryption type:XXXXXXXXXXXXXXX
:802.11n/g/b (2.4GHz)
:WPA-PSK
:AES
SCBFT800_VQT2Z56_eng.book  19 ページ  ２０１０年８月４日　水曜日　午後５時１０分
 
						

							20
VQT2Z56
≥If you can not find the SSID*2, select “Search again”.
2 Press [RETURN] and then press [OK].
Then select an item on the following screen which 
corresponds to the authentication type noted down in step 
1 (>19).
Follow the on-screen instructions to make the settings.
≥ Input your encryption key code in “Encryption Key” 
supplied with your Wireless router (Access point).
	*1 Wi-Fi Protected Setup-compatible Wireless router (Access point) may 
have the mark.
*2 An SSID (Service Set IDentification) is a name used by wireless LAN to  identify a particular network. Transmission is possible if the SSID 
matches for both devices.
Access Point Connection Setting Network Easy Setting (Connection Test)
Network Easy Setting (Internet Connection Test)
When you experience 
problems with settings
DisplayCheck the following
A conflict with other 
devices occurred. ≥
Please wait a few moments, 
and then try again.
A time out error occurred. ≥
Setting of the Wireless 
router (Access point) for 
MAC Address etc.
≥ The signal may be weak. 
Using the USB extension 
cable supplied with the 
Wireless LAN Adaptor, 
adjust the position of the 
Wireless LAN Adaptor.
≥ The SSID and the 
encryption key of the 
Wireless router (Access 
point).
≥ Please wait a few moments, 
and then try again.
An authentication error or a 
time out error occurred.
A device error occurred.
≥
Connection of Wireless LAN 
Adaptor
If there is no improvement in 
symptom, consult your 
dealer.
Access Point Connection Setting
WPA2-PSK (AES/TKIP)
WPA-PSK (AES/TKIP)
Open/Shared Key (WEP)
Open system
Select authentication type.
 
OK
Access Point Connection Setting
Yes No
Failed to connect to the access point.
A conflict with other devices occurred.
Do you wish to setup Access Point 
Connection Setting again ?
DisplayCheck the 
following
1. LAN cable connection or 
Connection to access point :Fail
≥
Connection of 
the LAN 
cables ( >17)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or 
Connection to access point :Pass≥
Connection 
and settings 
of the hub 
and router
≥ Settings of 
“IP Address / 
DNS 
Settings” 
(> 41)
2. IP address setting :Fail
3. Connection to gateway :Fail
1. LAN cable connection or 
Connection to access point
:Pass
2. IP address setting :Home 
network 
available
3. Connection to gateway :Fail
1. LAN cable connection or 
Connection to access point :Pass
2. IP address setting :Pass
3. Connection to gateway :Fail
DisplayCheck the following
Cannot find the server.
(B019) ≥
“Primary DNS” and “Secondary 
DNS” settings of “IP Address / 
DNS Settings” ( >41)
Failed to connect to 
the server.
(B020) ≥
The server may be busy or the 
service may have been 
suspended. Please wait a few 
moments, and then try again.
≥ Settings of “Proxy Server 
Settings” (> 41) and the router
OK
Network Easy Setting (Connection Test)
YesNo
Complete.
1. LAN cable connection         
2. IP address setting
3. Connection to gateway
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. 
Select “No” and press [OK] to finish Network 
Easy Setting.
: Fail
: Fail
: Fail
OK
Network Easy Setting (Internet Connection Test)Complete.
- Connection to the Internet       :   Fail(B019)
Failed the connection test.
Cannot find the server.(B019)
Please refer to the operating instructions for the cause
of the error and the countermeasure for it.
Press [OK].
SCBFT800_VQT2Z56_eng.book  20 ページ  ２０１０年８月４日　水曜日　午後５時１０分