Panasonic Recordable Dvd Home Theater System Sc Ht1000 Operating Instructions

							31
RQT7061
EDITING
[RAM]
5Press [ENTER] at the start point of the 
section you want to erase.
6Press [ENTER] at the end point of the 
section you want to erase.
To continue using Shorten Segment
1 Press [3, 4] to select “Next” and press [ENTER], then press [2] 
to select “Erase” and press [ENTER].
2 Repeat steps 5 and 6.
3Press [3, 4] to select “Exit” and 
press [ENTER]. 
4Press [2] to select “Erase” and press 
[ENTER]. 
Segments are erased from the start to end point.
[Note]
≥You can use basic functions like fast forwarding and slow play 
(➡page 18).
≥Play pauses if the end of the program is reached during this 
procedure.
≥You cannot specify an end point before a start point. 
≥You may not be able to specify points within 3 seconds of each 
other.
≥You cannot specify points on still pictures in the program.
≥The disc’s available recording time may not increase after erasing 
short segments.[RAM]
Select a point at which to divide the program into two.
5Press [ENTER] at the point you want 
to divide the program.
To confirm the division point
Press [3, 4] to select “Preview” and press [ENTER]. (Play 
will begin from a point 10 seconds prior to and after the 
division point.)
To change the division point
Restart play and press [3, 4] to select “Divide”, then press 
[ENTER] at the point you want to change.
6Press [3, 4] to select “Exit” and 
press [ENTER].
7Press [2] to select “Divide” and press 
[ENTER].
The program is divided.
[Note]
≥The divided programs retain the title and CPRM property 
(➡page 51) of the original program.
≥A very small portion of the recording preceding the division point 
may be lost.
≥It is not possible to carry out Divide Program in the following cases:
–when the program is extremely short.
–when the total number of programs is more than 99.
Shorten Segment
Shorten
     Segment
0 : 00 . 01Start– : – – . – –End3
StartEndNextExit
0 : 00 . 01
PLAY03
RETURN ENTERSELECT
N
S
0 : 00 . 01StartEnd3
StartEndNextExit
0 : 10 . 15
RETURN ENTERSELECT
0 : 10 . 15
N
SShorten
     Segment03
3
Divide Program
Divide
     Program
Divide3
PreviewDivide
Exit
0 : 00 . 01
0 : 00 . 01
03
RETURN ENTERSELECT
N
S
7061en.book  31 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							32
RQT7061
EDITING
Disc setting
[RAM] [DVD-R]
Entering text (➡page 26)
[RAM]
If set, this will protect the disc from accidental erasure.
4Press [2] to set disc protection and 
press [ENTER]. 
The lock symbol appears closed when the disc is write-
protected.
[RAM]
4Press [2] to select “Yes” and press 
[ENTER].
5Press [2] to select “Start” and press 
[ENTER].
All programs and play lists are erased.
[Note]
≥Computer data cannot be erased.
≥Erase does not work if one or more programs are protected.
Common procedures
Preparation
Release protection before proceeding with “Enter Title”, “Disc 
Protection”, “Erase all programs” or “Format”. [RAM]
(Cartridge ➡page 8, disc➡right, program➡page 30)
1While stopped
Press [FUNCTIONS].
2Press [3, 4, 2, 1] to select “DISC 
SETTING” and press [ENTER].
e.g., DVD-RAM
3Press [3, 4] to select the item and 
press [ENTER].
To stop set up process
Press [RETURN].
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3SLOW/SEARCH CANCEL
123
4
56
789
0
100
HOME THEATER TV
STATUSMULTI REARMARKERS.POSITIONF. R e cC.FOCUSREC MODE
CH SELECTRETURN
P.MEMORY
EQ/SFCERASE ADD/DLT
PROG/CHECK
L1/OPT
FUNCTIONSTOP MENU
ENTER
DIRECT NAVIGATOR
MENU PLAY LIST
MIX
2CHFRAME
REC
TEST
CM SKIP
SETUP
MUTING AUDIO
S W. LEVEL
FM/AM
TV/VIDEO
INPUT SELECT OPEN/CLOSEDISPLAY
DV DVCR Plus+POWERPOWER
PRO LOGIC  
TIME SLIP
SHIFTSHIFT
FUNCTIONSRETURN 3, 4, 2, 1
ENTER
Prog #
Disc Protection
DISC SETTING
Enter Title
Off
FormatRETURNENTERSELECT
7
Used Total MarkFree
10 0 : 580 : 42 (SP)
Erase all programs
[Note]
Once all programming has been erased or the disc has 
been formatted, the contents cannot be restored. Check 
carefully before proceeding.
≥Once a program is erased the play list which was created 
from that program is also erased.
Enter Title
Disc Protection
Erase all programs
DISC SETTING
RETURNENTERSELECT
Prog # 7
Used Total MarkFree
10 0 : 580 : 42 (SP)
Disc ProtectionEnter Title
On
FormatErase all programs
7061en.book  32 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							33
RQT7061
EDITING
[RAM]
Some DVD-RAM are unformatted. Format them before using them in 
this unit. Formatting also allows you to erase the entire contents of a 
disc.
Preparation
If the disc is dirty, clean it with the recommended cleaner 
(➡page 53) before formatting.
4Press [2] to select “Yes” and press 
[ENTER].
5Press [2] to select “Start” and press 
[ENTER].
Formatting starts.
≥A message appears when formatting is finished.
6Press [ENTER] to complete the 
procedure.
To stop formatting
Press [RETURN].
≥You can cancel formatting if it takes more than 2 minutes. The disc 
must be reformatted if you do this.
[Note]
≥Do not disconnect the AC power supply cord while the 
message “Formatting the disc” is on the television. This can 
render the disc unusable.
≥Formatting normally takes a few minutes, however it may take up to 
a maximum of 70 minutes.
≥The contents on the disc are erased when you format it even if you 
have set program or disc protection.
≥It may not be possible to use a disc on this unit if you cannot format 
it.
≥Formatting cannot be performed on DVD-R or CD-R/RW.
≥Formatting erases all contents on the disc, including computer 
data.[DVD-R] (DVD-R recorded on this unit only)
You can play DVD-R on compatible DVD players by finalizing them 
on this unit, effectively making them into DVD-Video that complies 
with DVD-Video standards.
4Press [2] to select “Yes” and press 
[ENTER].
5Press [2] to select “Start” and press 
[ENTER].
Finalizing starts.
≥A message appears when finalizing is finished.
6Press [ENTER] to complete the 
procedure.
[Note]
≥Do not disconnect the AC power supply cord while the 
message “Finalizing the disc” is on the television. This will 
render the disc unusable.
≥Finalizing takes up to 15 minutes.
After finalizing..
≥You cannot record or perform editing such as giving titles and 
erasing programs.
≥Programs longer than 5 minutes are divided into about five-minute 
chapters.
≥There is a pause of several seconds between program segments.
≥These DVD-R can be played on other Panasonic DVD players, but 
this is not guaranteed. Play may not be possible due to the player 
you are using, the DVD-R, or the condition of the recording. Play 
the disc using this unit if you experience problems with other 
equipment.
Visit Panasonic’s homepage for more information about DVDs. 
http://www.panasonic.com/playDVD-R
For your reference
The markers you entered (➡pages 18 and 23) will be lost.
FormatFinalize
7061en.book  33 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							34
RQT7061
RADIO & 
SOUND
The radio
Preparation
≥Switch [HOME THEATER, TV] to “HOME THEATER”.
≥Press [FM/AM] to select “FM” or “AM” as the source.
1Press [X TUNING] or [TUNING W] to 
select the frequency of the required 
station.
Remote control: Press [6] or [5].
TUNED: Displayed when a radio station is 
tuned.
ST: Displayed when a stereo FM 
broadcast is being received.
Press and hold [X TUNING] or [TUNING W] ([6] or [5] 
on the remote control) until the frequency starts scrolling to 
start automatic tuning. Tuning stops when a station is found.
2Adjust the volume.
[Main\unit\only]
∫If noise is excessive
Press [FM MODE].
Each time you press the button:
FM: Changes between stereo and forced monaural.
AM: BP1()BP2 (BPlBeat Proof)
Select either BP1 or BP2, whichever receives better reception.
The FM mode is canceled when you change the frequency.
∫FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive 
broadcasts allocated 0.1-MHz steps.
1 Press [FM/AM] to select “FM”.
2 Press and hold [FM/AM].
After a few seconds the display changes to show the current 
minimum frequency. Continue to hold the button down. The 
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM and AM frequencies preset in channels will be initialized by 
this procedure. Preset them again.Preset channels to make selection simple.
Up to 12 stations can each be set in the FM and AM bands.
[Main\unit\only]
1Tune to “FM 87.9” MHz or “FM 
87.5” MHz (➡left).
2Press and hold [MEMORY].
Release the button when “AUTO” is displayed.
The tuner presets all the stations it can receive into the 
channels in ascending order.
“SET OK” is displayed when the stations are set. The last 
station to be set is then played.
3Tune to “AM 520” kHz.
Repeat step 2 for AM automatic presetting. 
“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
[Main\unit\only]
1Tune to the station (➡left).
2Press [MEMORY].
3While “MEMO” is flashing
Press [X, W CHANNEL] to select a 
channel and press [MEMORY].
The station occupying a channel is erased if another station is preset 
in that channel.
1Press [FM/AM] to select “FM” or 
“AM”.
2Press the numbered buttons or
[W X CH] to select the channel.
e.g., “2”: [0] ➡ [2]
“12”: [1] ➡ [2]
[Note]
If there is nearby electrical interference during auto tuning the 
frequency may come to a halt without locating a channel. Turn off the 
power of the nearby electrical equipment.
Manual tuning
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3SLOW/SEARCH CANCEL
123
4
56
789
0
100
HOME THEATER TV
CH SELECTRETURN
L1/OPT
FUNCTIONSTOP MENU
ENTER
DIRECT NAVIGATOR
MENU PLAY LIST
MIX
2CHTESTFM/AM
TV/VIDEO
INPUT SELECT OPEN/CLOSEDISPLAY
DV DVCR Plus+POWERPOWER
PRO LOGIC
6, 5 HOME  
THEATER,TV
W X CH
r s VOLUME
FM/AM
DOWNTIME SLIP
RECERASEMEMORYFM/AMDV DREC MODEFM MODEUP
VOLUMEOPEN/CLOSETUNING
TIME SLIP
CHANNEL
PHONES
X, W CHANNEL
FM/AMMEMORYFM MODE
VOLUME DOWN, UPX TUNING W
Numbered 
buttons
STTUNEDFM
Preset tuning
Automatic presetting
Manual presetting
Selecting channels
CHSTMEMOTUNEDFM
CHSTTUNEDFM
7061en.book  34 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							35
RQT7061
RADIO &
SOUND
Use FM outdoor antenna if radio reception is poor.
[Note]
≥Disconnect the outdoor antenna when the unit is not in use.
≥Do not use the outdoor antenna during an electrical storm.
Optional FM antenna connection
A
AC INVHF/UHF
RF IN
RF OUT
R-AUDIO-L
COMPONENT
VIDEO OUT(480P/480I)Y
P
B
PR
EXT LOOP75
VIDEO S-VIDEO
IN1
IN3
R-AUDIO-L R-AUDIO-L
VIDEO
OPTICAL
IN
AM ANT FM ANT
(L1)
(L3)S-VIDEO
LOOP
ANT
GND
VIDEO S-VIDEO
OUT
11 2
FM outdoor antenna (Using a television antenna)
≥Disconnect the FM indoor antenna.
≥The antenna should be installed by a competent technician.
Rework your outdoor antenna’s 75 ≠ coaxial cable as follows.75 ≠ coaxial cable
(not included)
Antenna plug
(included)
1Remove a piece of the 
outer vinyl insulator.
10 mm (
13/32z)
10 mm (
13/32z)
Peel back2Carefully pull the tabs apart to 
remove the cover.3Install the coaxial cable.
Clamp the cable conductor, 
and wind it on so that it does 
not contact anything else. 4Attach the cover.
Clamp with pliers
7 mm (
9/32z)
7061en.book  35 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							36
RQT7061
RADIO & 
SOUND
Sound
≥Dolby Digital and DTS are digital encoding systems used on DVD 
to carry surround sound. Both were originally developed for use in 
cinemas.
≥This unit automatically recognizes and decodes these systems.
Play a Dolby Digital or DTS source.
The Dolby Digital or DTS indicator lights.
∫To down-mix Dolby Digital or DTS (multiple-
channel) signals to 2 channels
Press [SHIFT]i[MIX 2CH].
To cancel, press [SHIFT]i[MIX 2CH] 
again.
When “D.MIX” flashes on the display [DVD-A]
The DVD-Audio contains multiple-channel signals that cannot be 
down-mixed.≥When connected with headphones, the following sound field 
systems cannot be used. (Excluding Sound Field Control)
≥You may experience a reduction in sound quality when these 
sound field systems are used with some sources. If this occurs, 
turn the sound field system off.
The Dolby Pro Logic II processor works not only on sources 
recorded with Dolby Surround, but also on any stereo source.
1Press [SHIFT]r
[ÎPRO LOGIC II].
Each time you do this:
OFF>MOVIE>MUSIC>PANORAMA
^---------------------------------------------------}
MOVIE:Use this mode when playing movie software, 
especially videotapes, recorded in Dolby Surround.
MUSIC:Adds surround effects to stereo sources.
PANORAMA:Sound is spread out more so you feel like you 
are surrounded by music.
2Play a Dolby Surround or stereo 
source.
To cancel
Select “Dolby PLII OFF”.
[Note]
This does not work when playing multi-channel Dolby Digital.
Press [EQ/SFC] to select a setting.
Each time you press the button:
FLAT:Canceled (no effect is added) (factory preset).
HEAVY:Adds punch to rock.
CLEAR:Clarifies higher sounds.
SOFT:For background music.
DISCO:Reverberates sound to make you feel like you were in a 
disco.
LIVE:Makes vocals more alive.
HALL:Expands sound to make you feel like you were in a hall.
To check the current setting
Press [EQ/SFC].
You can make the sound of the center speaker seem 
like it is coming from within the television.
Press [SHIFT]r[C.FOCUS].
Each time you do this:
CENTER FOCUS ON>CENTER FOCUS OFF
 ^------------"-------------""-"""""---=}
≥This will have less effect when Dolby Pro Logic II 
is turned on.
Dolby Digital and DTS
Software encoded with Dolby 
Digital can be identified with 
this mark.Software encoded with DTS can 
be identified with this mark.
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3SLOW/SEARCH CANCEL
123
4
56
789
0
100
HOME THEATER TV
STATUSMULTI REARMARKERS.POSITIONF. R e cC.FOCUSREC MODE
CH SELECTRETURN
P.MEMORY
EQ/SFCERASE ADD/DLT
PROG/CHECK
L1/OPT
FUNCTIONSTOP MENU
ENTER
DIRECT NAVIGATOR
MENU PLAY LIST
MIX
2CHFRAME
REC
TEST
CM SKIP
SETUP
MUTING AUD IO
S W. LEVEL
FM/AM
TV/VIDEO
INPUT SELECT OPEN/CLOSEDISPLAY
DV DVCR Plus+POWERPOWER
PRO LOGIC  
TIME SLIP
SHIFTSHIFT
MIX 2CH
MULTI REAR
SHIFT
EQ/SFC
CH SELECT
ÎPRO LOGIC II
C.FOCUS
S.POSITION
S W.LEVEL TEST
i j VOLUME
3, 4, 2, 1
ENTER
DIGITALDTS
MIX 2CH
Dolby Pro Logic II
Sound Field Control
Center Focus
PL
SFC
CF
7061en.book  36 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							37
RQT7061
RADIO &
SOUND
This mode is useful if you have to place your 
surround speakers near the front speakers due 
to the layout of your room.
This mode makes it seem like the sound from 
the surround speakers is coming from behind 
you.
Press and hold [SHIFT]r[MULTI REAR] for 
more than 5 seconds.
Each time you do this:
V. R . S  O N
!)V. R . S  O F F
This mode makes it seem like sound is coming 
from multiple rear surround speakers virtually 
when connected with surround speakers.
Press [SHIFT]r[MULTI REAR].
Each time you do this:
M.R.S ON
!)M.R.S OFF
Using this function makes you feel like you are 
sitting in the ideal seating position (in the center of 
the circle formed by the speakers), even if you 
cannot due to the layout of your room.
1Press 
[SHIFT]r[S.POSITION].
2While “SEAT POSITION” is displayed
Press [3, 4, 2,  1] to select a 
position.
To cancel
Press [SHIFT]r[S.POSITION] again.
[Note]
While virtual rear surround is on, the seat position is changed in 
three horizontal steps.
Press [S W.LEVEL].
Each time you press the button:
SUB W 1>SUB W 2>SUB W 3>SUB W 4 (factory preset)
 ^-------------------------------------------------------------}
Adjust the level of the speakers so they are the same apparent level 
as the front speakers where you would normally be sitting and 
listening. (L, R ➡below, Balance)
Preparation
≥Dolby Digital and DTS: Turn off the other sound field systems.
≥Dolby Pro Logic II: Press [SHIFT]i[ÎPRO LOGIC II].
1 Press [SHIFT]r[TEST] to output a test signal.
Lch: Front left
Cch: Center
Rch: Front right
RSch: Right surround
LSch: Left surround
2 Press [VOLUMEr] or [s] to set the volume level normally 
used for listening.
3 Press [3] (to increase) or [4] (to decrease).
L, R: (➡below, Balance)
C, RS, LS: j6 dB to i6 dB
To stop the test signal, press [SHIFT]i[TEST] again.
∫To adjust speaker level during play
1 Press [SHIFT]r[CH SELECT] to select the speaker. 
LR>Cch>RSch>LSch>SWch
^---------------------------------------------------}
SW: Subwoofer
≥You can only adjust SW if there is output from the subwoofer 
channel.
2 Press [3] (to increase) or [4] (to decrease).
L, R: (➡below, Balance)
C, RS, LS:j6 dB to i6 dB
SW: j6 dB to i6 dB
You can adjust the balance of the front speakers.
1 Press [SHIFT]r[CH SELECT] to select “L R”.
2 Press [2, 1] to adjust the “L”, “R” balance.
Virtual Rear Surround
Multi Rear Surround
Seat position
Virtual speakers
V.REAR
Virtual speakers
M.V.REAR
Adjusting the bass
Speaker level adjustments
Balance
7061en.book  37 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							38
RQT7061
SETTINGS
Changing the unit’s settings
This chart shows the initial settings for this unit. See pages 40–43 for details on menu operation.
≥Underlined items are the factory presets.
Continued on next page.
Summary of settings
Tabs Menus Options
ChannelAntenna System (➡page 40)≥TV≥CATV
Auto Channel Setting (➡page 40)
Preset Channel Caption (➡page 41)
Manual Channel Caption (➡page 41)
VCR Plusr CH Setting (➡page 10)
Set UpOff Timer
Select how long the unit remains on when it is not being 
used.≥2 hr≥6 hr≥Off
Remote Control Code (➡page 42)≥ Set Code 1
≥Set Code 2≥Set Code 3
Auto Clock Setting (➡page 43)
Manual Clock Setting (➡page 43)
Time Zone Adjust (➡page 43)≥j1≥0
≥i1
Re-initialize Setting
This returns all values in the SETUP menus, except for the 
clock, channel settings, ratings level, and display language, 
to the default settings.≥Ye s≥No
Disc(Playing a 
DVD disc)Audio
Choose the audio language. Some discs start 
in a certain 
language despite 
any changes you 
make here.≥English≥French≥Spanish
≥Original: The original language of each disc will be selected.
≥Other ¢¢¢¢: Input a code (➡page 50).
Subtitle
Choose the subtitle language.≥Automatic
: If the language selected for “Audio” is not available, 
subtitles of that language will automatically appear if 
available on that disc.
≥English≥French≥Spanish≥Other ¢¢¢¢
Menus
Choose the language for disc menus.≥English
≥French≥Spanish≥Other ¢¢¢¢
Ratings
Set a ratings level to limit DVD-Video play. The password 
screen is shown when you select levels 0 to 7.
To enter a password
1 Input a 4-digit password with the numbered buttons.
≥If you enter a wrong number, press [CANCEL] to erase it.
≥Do not forget your password.
2 Press [ENTER]. 
≥The lock symbol appears closed to show the rating is 
locked.
3 Press [ENTER] to confirm the 4 digits.Setting ratings (When level 8 is selected)
8 No Limit
: All DVD-Video can be played.
1 to 7: Prohibits play of DVD-Video with corresponding 
ratings recorded on them.
0 Lock All:  Prohibits play of all DVD-Video.
Changing ratings (When level 0–7 is selected)
≥Unlock Recorder≥Change Password
≥Change Level≥Temporary Unlock
If you insert a DVD-Video that exceeds the ratings limit you set, a message appears on the television.
Follow the on-screen instructions.
DVD-Video mode
Select how to play pictures contained on some DVD-Audio.
The setting returns to “Off ” when you change the disc or turn 
the unit off.≥On: You can play DVD-Video content on DVD-Audio.
≥Off
: DVD-Audio are played as DVD-Audio.
Video3-D Y/C Separation≥On: Reduces noise for recording by separating the luminance 
(Y) and color (C) signals received from the television 
station.
≥Off: Reduces the ghosting that occurs when recording fast 
moving images.
Hybrid VBR Resolution≥Automatic
: Video compression is automated providing efficient 
recording.
≥Fixed: Video compression is fixed when recording providing 
smooth video play.
Still Mode
Select the type of picture shown when you pause play.≥Automatic
≥Field: Less blurred field stills are shown. Select if jittering 
occurs when “Automatic” is selected.
≥Frame: Sharper frame stills are shown. Select if small text or 
fine patterns cannot be seen clearly when “Automatic” is 
selected.
7061en.book  38 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							39
RQT7061
SETTINGS
Tabs Menus Options
VideoSeamless Play
Turn seamless play on or off on discs with play lists.
≥Seamless Play does not work with programs recorded in 
LPCM or when using Quick View.≥On: The scenes in play lists are played seamlessly. This may 
cause shifting of the points where scenes change. Some 
play lists cannot be played seamlessly.
≥Off: The points where scenes in play lists change are played 
accurately, but the picture may freeze for a moment.
Black Level Control
Select normal, lighter or darker for adjusting the black level 
control to the desired setting for picture enhancement.≥Input Level (Lighter/Darker
):
Adjusts the black level of the input signal (e.g., L1, L2, L3)
≥Composite & S Video Output Level (Lighter
/Darker):
When connected to a TV through the VIDEO OUT or S-VIDEO 
OUT terminal
≥Component Video Output Level (Lighter/Normal
/Darker):
When connected to a TV through the COMPONENT VIDEO 
OUT (Y/P
B/PR) terminals
AudioPLAY t1.3 & Audio during Search
[RAM] [DVD-R] [DVD-A] [DVD-V] [VCD]
Choose whether to have sound during the first level of fast-
forward. 
≥You may hear sound regardless of this setting with some 
discs. [DVD-A]≥On
≥Off: Quick View (➡page 20) does not work.
D. Range Compression [DVD-V] (Dolby Digital only)
Change the dynamic range for late night viewing.≥On≥Off
Select MTS
Select whether to record the main or secondary audio type 
(SAP) when recording to DVD-R or when recording using 
LPCM sound (“Audio Mode for XP Recording” ➡below).≥Main≥SAP
–You cannot change secondary audio when recording audio to 
DVD-R from an external source.
Audio Mode for XP Recording
Choose the audio type when recording with XP mode.
≥Sound recordings made using LPCM require more 
information than usual. Consequently the picture quality of 
LPCM recordings may be less than that of normal XP mode 
recordings.≥Dolby Digital
 (➡page 51)≥LPCM (➡page 51)
Speaker
Set the delay time for your center and surround speakers.Multi Channel
Center: 0.0
/1.0/2.0/3.0/4.0/5.0 ms
Surround (L/R): 0.0/5.0
/10.0/15.0 ms
DisplayStatus Messages
Choose whether to show on-screen messages automatically.≥Automatic≥Off
Language of Display Message
Choose the language for these menus and the on-screen 
messages.≥English
≥Español≥Français
Blue Background≥On
≥Off: When you do not want to have the unit show the blue 
background when reception is weak.
FL Display
Changes the brightness of the unit’s display and the volume 
dial LED goes on or off.≥Bright
≥Dim
≥Automatic:The display turns dark during play, and reappears 
momentarily if a button is pressed. When the power is 
turned off all displays disappear. While using this 
mode the standby power consumption can be 
reduced.
TV 
ScreenTV Type (➡page 11)
Choose the setting to suit your television.≥Aspect 4:3 & 480I≥Aspect 4:3 & 480P
≥Aspect 16:9 & 480I≥Aspect 16:9 & 480P
4:3 TV Settings for DVD-Video
Select how DVD-Video widescreen picture is shown on a 4:3 
standard aspect television.≥Pan & Scan
 (➡page 51):
Video recorded for a widescreen is played as Pan & Scan 
(unless prohibited by the producer of the disc).
≥Letterbox (➡page 51):
Video recorded for a widescreen is played in the letterbox style.
4:3 TV Settings for DVD-RAM
Select how DVD-RAM widescreen picture is shown on a 4:3 
standard aspect television.≥4:3: Programs played as recorded.
≥Pan & Scan: Video recorded for a widescreen is played as Pan 
& Scan.
≥Letterbox
: Video recorded for a widescreen is played in the 
letterbox style.
7061en.book  39 ページ  ２００３年７月１日　火曜日　午前１１時４４分 
						

							40
RQT7061
SETTINGS
Changing the unit’s settings
See pages 38 and 39 for menu and option details.
1While stopped
Press [SHIFT]r[SETUP] to show the 
menus.
2Press [3, 4] to select the menu’s tab 
and press [1].
3Press [3, 4] to select the menu and 
press [ENTER].
4Press [3, 4] to select the option and 
press [ENTER].
The screen now shows the menu again.
≥Some items require different operations. Follow the on-screen 
instructions, or read the following explanations.
To return to the previous screen
Press [RETURN].
To exit the SETUP screen
Press [SHIFT]i[SETUP].The unit sets the channels automatically.
First, select to suit the type of antenna you are using. Channels are 
set corresponding to the antenna system you select.
While SETUP menu screen is displayed
1Press [3, 4] to select “Channel” and 
press [1].
2Press [3, 4] to select “Antenna 
System” and press [ENTER].
3Press [3, 4] to select “TV” or “CATV” 
and press [ENTER].
The screen shown in step 1 reappears.
4Press [3, 4] to select “Auto Channel 
Setting” and press [ENTER].
If you have not yet set clock, the “Auto Channel/Clock Setting” 
screen appears.
5Press [ENTER] to start Auto Channel 
Setting.
This takes a few minutes. When finished, press [ENTER].
To cancel partway
Press [RETURN].
Common procedures
CH
VOLUME
SKIP
STOP PAUSE PLAY/x1.3SLOW/SEARCH CANCEL
123
4
56
789
0
100
HOME THEATER TV
STATUSMULTI REARMARKERS.POSITIONF. R e cC.FOCUSREC MODE
CH SELECTRETURN
P.MEMORY
EQ/SFCERASE ADD/DLT
PROG/CHECK
L1/OPT
FUNCTIONSTOP MENU
ENTER
DIRECT NAVIGATOR
MENU PLAY LIST
MIX
2CHFRAME
REC
TEST
CM SKIP
SETUP
MUTING AUDIO
S W. LEVEL
FM/AM
TV/VIDEO
INPUT SELECT OPEN/CLOSEDISPLAY
DV DVCR Plus+POWERPOWER
PRO LOGIC  
TIME SLIP
SHIFTSHIFT
RETURN
SHIFT
CANCEL
SETUP 3, 4, 2, 1
ENTER
TA B
SELECT
Antenna SystemAuto Channel Setting
Channel Caption
Preset Channel CaptionManual Channel Caption
VCR Plusi CH SettingCATV
Channel SETUP
   RETURN
Set UpDiscVideoAudioDisplayTV Screen
Tabs Menus Options
Antenna System and Auto Channel 
Setting
Antenna SystemAuto Channel Setting
Channel Caption
Preset Channel CaptionManual Channel CaptionCATVSet UpDisc Channel SETUP
SETUP
Set UpChannel
Antenna System
TV
CATV
7061en.book  40 ページ  ２００３年７月１日　火曜日　午前１１時４４分