Panasonic Rear View Camera Cy Rc50u Operating Instructions

 Consult your dealer if any item is missing.
O   Figures in (  ) are quantities.
 Rear view camera 
control unit
(1)
 Power  cord
(2)
 RCA  cord
(1)
Q  Accessories
 Operating  instructions 
(this manual)
(1)
 Owners  information 
card
(1)
 Camera  bracket
(1)
 Cord  rail
 Rear view camera(with Rubber water seal)
 4 m cord
 Bolts with washer
(1)
 Hexagon  wrench
 M3 × 6 mm
 Velcro  tape
(4) (1) 38 × 70 mm
(1)(1)
 Tie  band
(2)
 Cord  clamp
 18  cm
 Double-sided  tape
(7)
(1)  30 × 70 mm
 Clip  connector...

O   Route the camera cord so that it does not allow rainwater etc. to penetrate.O   Allow enough slack in the cord so that it is not pulled when the door is opened and closed.
 Rear view camera
 Rear view camera 
control unit Cord  clamp
 Harness  cover Route the cord above the back door 
(outside).
 Do not route the cord under the back 
door (inside). Fasten with cord clamps at 
key points, then bring the 
cord in where the clearance 
from the edge of the door 
is wider.
 The cord will be damaged if...

 Note:O   Open and close the back door or trunk lid slowly to check that the camera cord is not 
pinched or abraded by the door/lid. Moisture or water can enter through the damaged area 
of the cord and penetrate to the interior of the camera, causing breakdowns.
O   Route the camera cord as far as possible from the antenna cord.
(It could cause noise in TV and radio signals.)
O   If AM radio broadcasts are affected by noise, move the camera cord further from the vehicle 
wiring harness. Rear view camera...

 Note:O   The camera cannot be affi xed to painted or glass surfaces which have been treated 
with fl uoroplastics (treatments which shed water droplets, mud etc.), or to re-painted 
surfaces.  Make connections and placement tentatively at fi rst, to check positions. Repeated 
affi xing weakens the adhesive.
O   The screw holes to use, and the possible angle adjustment, vary according to the 
mounting position. Adjust the angle and check that the required fi eld of view is 
visible. (It is not possible to...

 Wipe away all oil and dirt etc. from the mounting surface.
 Note:
Do not mount the control unit in the following locations, which could cause breakdowns.
OPlaces exposed to waterOPlaces which could be stepped onODusty placesOClose to heater ducts or heat-emitting objectsOPlaces exposed to direct sunlightOUnder the carpet, or any other position that gets hot
Before mounting
 Rear view camera control unit Rear view camera control unit
 Velcro  tape  Double-sided  tape
 Rear view camera control unit...

3&7&34&
(/%
1 A
108&3$.&3
*/7*%&0
065
 Camera  input (CAMERA IN)
 Video  output (VIDEO OUT)
 When connected to a Panasonic Car Monitor etc., the image from the camera is automatically 
displayed in the screen when the shift lever is moved to reverse (R).
O   For some combinations of vehicle type and device, additional cords (option) may be 
required, or connection may not be possible.
   Consult your dealer or service center.
O   For connection with products from other companies, consult the manufacturer...

ording to the installation instructions for the connected devices.
P
R
N
D
2 L
1A
´µ Clip  connector
 (supplied  with 
CN-NVD905U)
 Reverse  lead
 (Violet/white  stripe) Ground  lead
 (Black)Battery
Car chassis
 Rear  view  camera 
 (4  m)
 RCA  cord 
 (6  m)  (Yellow) (Yellow)  Car Navigation System
 (CN-NVD905U:  option)
 Rear view camera – RCA conversion cable
  (supplied  with  CN-NVD905U)Clip connector
 Cut off the end terminal 
and connect to the clip 
connector.
P
R
N
D
2 L
1A
´µ
CAMERA-IN...

P
RND
2 L
1 A3&7&34&(/%


´µ
 Car  MonitorVideo input
 How to disconnect locked cords
 Power cord  Rear view camera 
cord
 How to attach a clip connector

  Insert the cord into the 
clip connector.
 Vehicle-side  wiring  cord
 Reverse lead of this unit
  Press the element into 
place.

  Close the cover.
 Reverse  lead
 (Violet/white  stripe) Ground  lead
 (Black)Car chassis
 Rear view camera 
 (4  m)
 RCA  cord 
 (6  m)  (Yellow)Clip connector  Reverse  lampTransmission
 Rear  view  camera...


  Adjust the camera angle so that the fender or the rear edge of the vehicle 
appears at the bottom of the monitor.

  Attach the camera bracket to a glass or painted surface on the vehicle 
body.
Side view 
  Mount the camera body onto the camera bracket. Bolt with washer
 Hexagon  wrench
 Rear view camera
 Side with logo 
uppermost The screw holes to use, and the possible angle 
adjustment, vary according to the mounting 
position.
 Mount on the screw holes 
on the side opposite 
the direction of...

Memorandum