Panasonic Raid Board Wj Ndb301 Operating Instructions

RAID Board
Instructions
Model No.WJ-NDB301
Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.
THIS PUBLICATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR
NON-INFRINGEMENT OF THE THIRD PARTY’S RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS....

2
Unplug the power cord from the WJ-ND300 before
installing the board.
This board is exclusively designed for the WJ-ND300
(sold separately).
Do not install this board in other devices or use this board
independently.
Keep unused board in an antistatic bag.
The board is shipped in an antistatic bag. Discharge static
electricity from your body by touching a metal object such
as a metal locker before opening the bag to protect the
board from static electricity.
Do not touch the parts (circuits) on the...

3. Connect between the main and RAID boards with 2
cables that belong to the main board.
4. Detach the cable from the cable clamp to unbind it, and
pass the cable through the cable clamp as shown in
the illustration below.
3
INSTALLATIONS
1. Unscrew WJ-ND300 (2 screws from top, 4 screws from
sides, and 5 screws from rear) and remove the top
cover.
2. Disconnect all of the HDD cables.
HDD cables
To main board
To RAID board
Hold the 
cables using 
the cable 
clamp. 

(1) Use the HDD cable holding clamps attached to the
RAID board to bundle two of the HDD cables each
disconnected in Step 2.
(2) Connect all of the HDD cables and 3 cables to the
RAID board.
7. Put the top cover back and secure it with the screws
removed in Step 1. 5. Mount the RAID board.
(1) Mount the RAID board so that the mounting holes
(qto r) of the RAID board are aligned with the
mounting holes (qto r) of the main unit (WJ-
ND300) respectively by referring the illustration.
(2) Secure the RAID...

5
SETUP
• The settings relating to the RAID function can be performed on the setup menu displayed on the LCD on the front panel of
the unit. Refer to the Installation Guide for further information.
• Refer to the operating instructions of the Network Disk Recorder WJ-ND300 for descriptions of the connections.
TROUBLESHOOTING
Problem
The hard disk drive is not rec-
ognized.
The unit runs in the SINGLE
mode.
MIX ERROR occurs. (The
SYS-2 SINGLERAID MIX
ERROR indication appears.)
• Is the HDD cable connected...

6
STANDARD ACCESSORIES
Instructions (this document)  ............................................ 1 pc.
Board Fixing Screws  ........................................................ 8 pcs
Board Fixing Screw (flat-head) ........................................ 1 pc.
Cable ................................................................................ 2 pcs.
SPECIFICATIONS
Required Power: +5 V DC (Supplied from WJ-ND300)
Power Consumption: 1.2 A at +5 V DC
Operating Temperature: From +5°C (41°F) to +45°C...

7
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products
should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where
they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your
products to your local...

For U.S., Canadian and Puerto Rican fields:
Panasonic System Solutions Company, 
Unit Company of Panasonic Corporation of North America
Security Systems 
www.panasonic.com/security
For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
Zone Office
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094 
Central: 1707 N. Randal Road, Elgin, IL 60123 
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024 
Western: 6550 Katella Ave., Cypress, CA...