Panasonic Pv L751 Operating Instructions Manual

							11
Getting Started
Cassette Information
1Turn Tape Wheel in direction of arrow
until there is no slack.
2Attach Battery (page 9).
3Slide TAPE EJECT to open door.
4Insert cassette as shown.
5Press here to close door.
1
2 3
4
• To remove the cassette, slide the TAPEEJECT switch.5
1To prevent accidental erasing,
break off tab with screwdriver.
(Or, slide tab open.)
2To record again,
cover hole with adhesive tape.
(Or, slide tab closed.)
Protects tapes from being accidentally
erased.
Erase Protection Tab
Cassette Insertion/Removal
Slide tab type
12
• SLP playback may contain more picture noise.SLP
(Super Long Play)
SP
(Standard Play)
Cassette type
Tape Speed
Selector Position
TC-20
20 minutes
1 hour30 minutesTC-30 TC-40
40 minutes
1 hour
30 minutes2 hours
Use tapes with the  mark in this unit.
Record/Playback Time 
						

							12For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Using MENU Mode
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA or VCR.
1Press MENU for MENU mode.
The CAMERA or VCR MENU screen (see
below left) appears when Menu mode is
entered.
2Press UP 
 or DOWN  to highlight the
desired menu item.
3Press DISPLAY to set selection.
4Press MENU to exit.
Note:
• The Menu mode is canceled if 
UP/DOWN(
/),DISPLAY, or MENU are not pressed within 5
minutes when Self Demo mode is off.
• The Menu mode is canceled if 
UP/DOWN(
/),DISPLAY, or MENU are not pressed within 30
seconds when Self Demo mode is on.
SELECT:  PUSH  /
  KEY
SET:  PUSH  DISPLAY  KEY
END:  PUSH  MENU  KEY
PROGRAMMED  REC
PROGRAMMED  REC
TI TITLE
TLE;  AUTO/MANUAL
AUTO/MANUAL
SHUTTER SHUTTER;  AUTO
AUTO
STAND-BY  RELEASE  ;  OFF STAND-BY  RELEASE  ;  OFF
CLOCK  SET CLOCK  SET

---  MENU  
  MENU  ---   PAGE  
   PAGE  1/2
1/21
2
3
4
5
6
7
8
9DISPLAY;  ON
SELF  DEMO;  OFF
SECURITY;  OFF
VIDEO  EFFECTS  ;FADE
BLACK
SELECT:  PUSH  
:  PUSH  /
  KEY
  KEY
SET SET:  PUSH  
:  PUSH  DI
DISPLAY  KEY
SPLAY  KEY
END END:  PUSH  MENU  KEY
:  PUSH  MENU  KEY
PAGE  2/2
MENU Mode (VCR) Screen
MENU Mode (CAMERA) Screen1PROGRAMMED REC (page 18).
Camcorder starts and stops recording at a
preset time.
2TITLE (pages 32, 33).
AUTO/MANUAL : 16 items
PHRASE            : 10 items
3SHUTTER (page 25).
Select desired shutter speed.
4STAND-BY RELEASE (page 17).
ON : Enables quick resumption of recording
from Stand-by mode.
5CLOCK SET (pages 13, 14).
Select to set clock.
6DISPLAY (page 47).
ON : On-screen Display (OSD) screens are
displayed.
7SELF DEMO (page 7).
ON : SELF DEMO screen is displayed.
8SECURITY (page 31).
ON : Enables Motion Security recording.
9VIDEO EFFECTS (pages 26~28).
AUTO FADE : BLACK or WHITE
DIGITAL FADE : TYPE
7 types
COLOR8 colors
DIGITAL FILTER : COLOR5 colors
 5
 6---  MENU  ---
CLOCK  SET
DISPLAY;  ON
SELECTSELECT:  PUSH  :  PUSH  /
  KEY  KEYSETSET:  PUSH  :  PUSH  DIDISPLAY  KEYSPLAY  KEYENDEND:  PUSH  MENU  KEY:  PUSH  MENU  KEY
MENU
MENU
UP
UP
DOWN
DOWN
DISPLAY
DISPLAY
FOCUSFAR
NEAR
1, 432 
						

							13
Getting Started
Setting the Clock
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA or VCR.
Set the following items in order: Time
Zone, Daylight Saving Time, Date,
and Time.
           - - -  CLOCK SET  - - -         - - -  CLOCK SET  - - -            
SELECT :  PUSH  /
 KEY
SET        :  PUSH  DISPLAY  KEY
END       :  PUSH  MENU  KEY
TI TIME  ZONE
ME  ZONE;  EASTERN
;  EASTERN
D. S. T. D. S. T.;  AUTO
;  AUTO
DATE /  DATE / TI
TIME
ME;  12 : 00 : 00AM
;  12 : 00 : 00AM
       JAN  1   2001         JAN  1   2001 
SELECT
SELECT:  PUSH  
:  PUSH  /
  KEY
  KEY
SET SET:  PUSH  
:  PUSH  DI
DISPLAY  KEY
SPLAY  KEY
END END:  PUSH  MENU  KEY
:  PUSH  MENU  KEY
          - - -  MENU  - - -         
          - - -  MENU  - - -             
    CLOCK  SET
CLOCK  SET
DI DISPLAY          ;  ON
SPLAY          ;  ON
 
1Press MENU for MENU mode.
Press 
UP 
 or DOWN  to select
CLOCK SET .
2Press DISPLAY for
CLOCK SET menu.
Press 
UP 
 or DOWN 
to select TIME ZONE,
DST, or DATE/TIME.
3Press DISPLAY for menu of item selected in
step 2.
To change the setting:
TIME ZONEGo to step 3a on page 14.
D.S.T.Go to step 3b on page 14.
DATE/TIMEGo to step 3c on page 14.
4Press MENU twice to exit.
SELECT
SELECT:  PUSH  
:  PUSH  /
  KEY
  KEY
SET SET:  PUSH  
:  PUSH  DI
DISPLAY  KEY
SPLAY  KEY
END END:  PUSH  MENU  KEY
:  PUSH  MENU  KEY
---  MENU  
  MENU  ---   PAGE  
   PAGE  1/2
1/2PROGRAMMED  REC
PROGRAMMED  REC
TI TITLE
TLE;  
;  AUTO/MANUAL
AUTO/MANUAL
SHUTTER SHUTTER;  
;  AUTO
AUTO
STAND-BY  RELEASE STAND-BY  RELEASE  ;  OFF
  ;  OFF
CLOCK  SET CLOCK  SET
[ VCR  MODE ] [ CAMERA  MODE ]
1, 2, 3, 4MENU
UP
UP
DOWN
DOWN
DISPLAY
FOCUSFAR
NEAR
(continued on next page) 
						

							14For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Date and time including leap year are
calculated up to DEC 31, 2099.
Spring (First Sunday in April) :
ahead one hour.
Autumn (Last Sunday in October) :
back one hour. Clock will auto-adjust to daylight saving
time (DST).
- - DAYLIGHT SAVING TIME - -
SELECT :  PUSH  /
 KEY
SET        :  PUSH  DISPLAY  KEY
AUTO
OFF
ATLANTIC ATLANTIC EASTERN EASTERN CENTRAL CENTRAL MOUNTAIN MOUNTAIN
PACIFIC PACIFIC ALASKA ALASKA
HAWAII HAWAII
SAMOA SAMOA
11:00
10:00 7:00 8:00 9:00 2:0012:00
6:00 1:00
Setting the Time Zone
•When traveling, repeat this operation and
select one of the 8 listed time zones to
set the clock to local time.
Press 
UP 
 or
DOWN  to select
OFF or AUTO.
Press 
DISPLAY to
confirm entry. Press 
UP 
 or
DOWN  to select
local time zone.
Press 
DISPLAY to
confirm entry.
DST: AUTO
Press or hold down 
UP 
 orDOWN  to select hour, then
press DISPLAY to fix.
Repeat for minute, month, day,
and year.
Clock starts when year is
entered and 
DISPLAY is
pressed.
EXAMPLE :DISPLAY DISPLAY
FOCUS
FOCUSFAR
NEAR NEARUP
UP
DOWN
DOWN
- - - SELECT TIME ZONE  - - -
SELECT :  PUSH  /
 KEY
SET        :  PUSH  DISPLAY  KEY
ATLANT I CCPACIFICC
EASTERNALASKA
CENTRAL HAWA I I
MOUNTA I NNSAMOA 
Note:
•Auto DST does not function if time zone
is set to Hawaii or Samoa (see “Setting
the Time Zone” above). Note :
•Clock may lose or gain up to 2 minutes
per month.
• When traveling outside the listed time
zones, set clock to local time manually.
• To adjust or set clock, see “Setting Date
and Time” bottom of page.
The Camcorder is preset to DST: AUTO .
If DST is not observed in your area, set
to OFF by doing the following.
[ Time Zone chart ]
The Camcorder is preset to Eastern time.
Auto Daylight Saving Time
Setting Date and Time- - - DATE/TIME SETTING - - -
SELECT :  PUSH  /
 KEY
SET        :  PUSH  DISPLAY  KEY
1 2 : 0 0 : 0 0 A M
J A N     1   2 0 0 1
Setting the Clock (continued)
3a
3b
3c 
						

							15
Basic Operation
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
appears in EVF or
LCD monitor when
Light is on. Set 
LIGHT to AUTO.
Light turns on/off automatically according
to lighting conditions.
Or, set 
LIGHT to ON/OFF manually.
Caution:
Light becomes hot. Never cover Light
while on.
Note:
• Using Light reduces battery operating time.
• Provide proper ventilation when using
Light extensively in a hot environment.
• Using Light when the Camcorder is
powered by a car battery may shorten bulb
life.
• Set Light to OFF when not in use.For recording in dim lighting.
Using the Light
LIGHT LIGHTOFFAUTO
ON
12:00:00AM
JAN 1 2001SP
REC
1x
Replacing the Bulb
Note:
• Handle bulb gently. Excessive force may
cause bulb to crack.
1Press in on both sides of lens cover
and pull straight out and off.
2Using Tweezers or needle-nose
pliers, carefully remove bulb.
•Take unit to service center if you need
assistance.
3Replace bulb using a clean cloth or
tissue. (Do not touch with fingers.)
4Replace lens cover.
Before you begin...
• Order Part No. VULS0001 (VLLW0015 and
cushions) for replacement bulb unit.
• Set POWER to OFF.
1
4
2
3
DANGER:
Use only replacement bulb (PART NO. VLLW0015) supplied by Panasonic to reduce
risk of fire.
Handle new bulb with cloth or tissue as skin oils will decrease bulb life.
Remove lens cover and allow bulb to cool before replacing to avoid possible burn
hazard.
Built-in Auto Light 
						

							16For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Camera Recording
PAUSE
RECORD
SP
Before you begin...
• Connect Camcorder to power source.
• Insert cassette with record tab (page 11).
View recording scene on EVF or LCD
(Liquid Crystal Display) monitor.
Recording via EVF or LCD
Monitor
1Press LCD-OPEN to unlock the LCD
monitor. Swing LCD monitor fully open
and adjust viewing angle.
• If you want to record using EVF, close
and lock LCD monitor.
2Set POWER toCAMERA.
Lens Cover opens.
Power Lamp lights.
• Be sure POWER
is fully turned to
CAMERA position.
• EVF or LCD monitor turns on/off by the
POWER switch.
• EVF shuts off when LCD monitor is
opened and turns back on when LCD is
closed.
• Both EVF and LCD monitor turn on
when LCD is at 180 (see above left).
This allows both you and the subject to
view the recording.
3LCD : Turn BRIGHT control to
monitoradjust LCD monitor
brightness level.
EVF : Look into EVF and adjust
VISION ADJUSTMENT to
your eyesight.
4Hold down TAPE SPEED for about 1
second to change tape speed to SP/SLP
(page 11).
5Press RECORD/PAUSE to start or
pause recording.
6Set POWER toOFF when finished.
• To remove the cassette, slide the
TAPE EJECT switch (page 11). Built-in Twin
Capsule 2-Way
Microphone
System
CAUTION :Rotating partially open LCD
monitor may block cassette door
and damage Camcorder body.
Note:• When Camcorder is aimed at excessively bright
objects, or bright lights, a vertical bar may
appear in the picture. This is normal for the
CCD pick-up. Try to avoid this when possible.
• Using LCD monitor reduces battery operation
time. Return LCD monitor to locked position
when not in use.
• To hear sound while recording, connect
earphone (M3 type: not supplied) to PHONE
jack. Earphone volume cannot be changed
while in CAMERA mode.
EVF or LCD Monitor
(Record/Pause mode)
EVF or LCD Monitor
(Record mode)
Tape speed
WARNING:• Do not leave the camcorder with the EVF
aimed directly at the sun. This may cause
damage to the internal parts of the EVF.
LCD-OPEN
BRIGHT
3
1
PHONE
(earphone)
jack
4
SPEED
SP/SLP
POWER  POWER 
REC REC
CAMERA
CAMERA
OFF OFF VCR VCRPHOTO PHOTO
6
Power
Lamp
2
5
VISION
ADJUSTMENT3 
						

							17
Basic Operation
Before you begin...• Connect Camcorder to power source.
• Insert cassette with record tab (page 11).
Camera Recording
SELECT SELECT:  PUSH
:  PUSH     
  /     KEY
KEY
SET SET:  PUSH  
:  PUSH  DI
DISPLAY  KEY
SPLAY  KEY
END END:  PUSH  MENU  KEY
:  PUSH  MENU  KEY
---  MENU  
  MENU  ---   PAGE  
   PAGE  1/2
1/2PROGRAMMED  REC
PROGRAMMED  REC
TI TITLE
TLE;  
;  AUTO/MANUAL
AUTO/MANUAL
SHUTTER SHUTTER;  
;  AUTO
AUTO
STAND-BY  RELEASE STAND-BY  RELEASE  ;  OFF
  ;  OFF
CLOCK  SET CLOCK  SET
1Set POWER to CAMERA.
2Press MENU for
MENU mode.
Press 
UP  or
DOWN  to
select
STAND-BY RELEASE .
3Press DISPLAY to select ON/OFF.
ON :From Stand-by mode, press
RECORD/PAUSE two times
to resume recording.
OFF :From Stand-by mode,
set 
POWER to OFF, then toCAMERA. Press RECORD/PAUSE to record.
4Press MENU to exit.
Stand-by Quick Release
If left in RECORD/PAUSE mode for 5
minutes, Camcorder switches to Stand-
by mode to conserve battery. When set
to ON, Stand-by Quick Release lets
you resume recording by pressing
RECORD/PAUSE two times. Stand-by
Quick Release is set to OFF at the
factory.
aPress RECORD/PAUSE to stop
recording.
bSet POWER to OFF and leave cassette
in Camcorder.
cTo resume recording, set POWER to
CAMERA.
dPress RECORD/PAUSE to resume
recording.
Note:
• Use Manual Easy Edit (left) if more than
24 hours before recording is resumed.
Manual Easy Editing
For a smooth transition between scenes if
recording is stopped, and then started
within 24 hours. For proper continuity when taping from Stop
mode or after attaching a new Battery.
Easy Edit Stand-by
ASet POWER to VCR.
BaPress REWIND/SEARCH to rewind
a few seconds of tape.
BbPress PLAY to review recording.
CcPress STILL where you want to
continue recording.
CSet POWER to CAMERA.
DPress RECORD/PAUSE to resume
recording.
B
2, 3, 4MENU
UP
DOWN
DOWN
DISPLAY
FOCUSFAR
NEAR
CAMERA CAMERA
OFF OFF VCRPHOTO PHOTO
STOP
STILL
PLAY
REWFF
+
DELc
b
aa, d,
D
1,
b, c,
A, C 
						

							18For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Before you begin...
• Connect Camcorder to power source.
Use AC Adaptor for longer recordings.
• Insert cassette with record tab (page 11).
• Set POWER to CAMERA.
Camera Recording
1Press MENU for MENU
mode. Press 
UP 
 or
DOWN to select
PROGRAMMED REC .
2Press DISPLAY.
(Current time is
displayed.)
Each additional press
of 
DISPLAY increases
start time by 30 minutes.
3Press DOWN to
select  REC TIME .
Press 
DISPLAY
repeatedly to select one
of the options shown at
left.
To cancel the setup, press 
MENU twice.
4Press RECORD/PAUSE
to place Camcorder in
stand-by mode.
Recording will be done as scheduled.
Note:
• Start time may not be set over 24 hours from
current time.
• Camcorder shuts off at tape end, or 12 hours
after Interval Recording starts.
• To cancel, set 
POWER to OFF.
       START ; 10:20PMREC TIME ;  10MIN.  
10:20:00PM
JUN 1 2001
STAND-BY
Set a recording start and stop time. Or,
set a 5 or 10 second interval recording
to be done each minute.
*1Record 5 seconds each minute.
*2Record 10 seconds each minute.
       
       
           START 
    START    ;
   ;   10 : 20PM
   10 : 20PMREC
REC TIME    ;   10MIN.
TIME    ;   10MIN.
10:20:00
10:20:00PM
PM
SELECT :  PUSH  
SELECT :  PUSH  /
 KEY
 KEY
SET        :  PUSH  DISPLAY  KEY SET        :  PUSH  DISPLAY  KEY
START   :  PUSH  RECORD  KEY START   :  PUSH  RECORD  KEY
CANCEL:  PUSH  MENU  KEY CANCEL:  PUSH  MENU  KEY
       
       
       START    ;        START    ;   10 : 20PM
   10 : 20PMREC
REC TIME
TIME    ;   10MIN.
    ;   10MIN.
10:20:00
10:20:00PM
PM
SELECT :  PUSH  
SELECT :  PUSH  /
 KEY
 KEY
SET        :  PUSH  DISPLAY  KEY SET        :  PUSH  DISPLAY  KEY
START   :  PUSH  RECORD  KEY START   :  PUSH  RECORD  KEY
CANCEL:  PUSH  MENU  KEY CANCEL:  PUSH  MENU  KEYREC TIME :
Programmed Recording
SELECT
SELECT:  PUSH  
:  PUSH  /
  KEY
  KEY
SET SET:  PUSH  
:  PUSH  DI
DISPLAY  KEY
SPLAY  KEY
END END:  PUSH  MENU  KEY
:  PUSH  MENU  KEY
---  MENU  
  MENU  ---   PAGE  
   PAGE  1/2
1/2PROGRAMMED  REC
PROGRAMMED  REC
TI TITLE
TLE;  
;  AUTO/MANUAL
AUTO/MANUAL
SHUTTER SHUTTER;  
;  AUTO
AUTO
STAND-BY  RELEASE  ;  OFF STAND-BY  RELEASE  ;  OFF
CLOCK  SET CLOCK  SET1, 2, 3MENU
UP
DOWN
DISPLAY
FOCUS
FOCUSFAR FAR
NEAR NEAR
CAMERACAMERAOFFOFFVCRVCRPHOTOPHOTO
4 
						

							19
Basic Operation
T
W
REW      SEARCH      FF
PLAY
STOPSTILLREC/
PAUSE
Remote Sensor
8-Function Remote Control
Controlled Functions
 1 POWER ZOOM
page 23.
 2 REWIND/SEARCH
page 20.
 3 PLAY
page 20.
 4STOP
page 20.
 5 RECORD/PAUSE
page 16.
 6 FAST FORWARD/SEARCH
page 20.
 7 STILL
page 20.
Important Note:
• After 5 minutes in Record/Pause mode,
the camcorder will shut off to conserve
battery power. If recording is resumed
within 30 minutes, press 
REC/PAUSE
once.
If over 30 minutes, set 
POWER to OFF,
then CAMERA, then press REC/PAUSE.
Remote Control Operation
Operate Camcorder’s main functions up to about 5 m (16 feet) away.
Aim remote at sensor on Camcorder.
1
2
3
45
6
7
Note:
• If you press REC/PAUSE on the remote
control with the LCD monitor rotated 180

to face the same direction as the lens/
subject, “RECORD” or “PAUSE” is
displayed on-screen in extra large
characters for confirmation. 
						

							20For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
Playing Back Recordings
Before you begin...
• Connect Camcorder to power source.
• Insert recorded tape.
Tracking Control
Quick Visual Search
Search Speed• SP   (Standard Play)     : 3 times normal.
• SLP (Super Long Play) : 9 times normal.
During playback, press:•FF     : fast forward search
•REW : rewind search
Press again or press PLAY for normal play.
Still Picture
Press STILL to freeze picture.
Press again for normal play.
This feature works best in SLP mode (page 11).
Special Effects
Note:• During search, horizontal noise bars will appear.
Audio is muted.
• To protect video heads and tape, operating
modes will revert as follows after 5 minutes:
Still Stand-by
Stand-by Power off (when Battery Pack is
used).
• Tape auto-rewinds if played or fast forwarded to end.
Note:• Using LCD monitor reduces battery operating
time. Return LCD monitor to locked position
when not in use.
• When earphone (M3 type: not supplied) is
connected to PHONE jack, speaker is muted.
           
    
1
1Press LCD-OPEN and swing LCD
monitor fully open.
• If you want to playback on EVF, close
and lock LCD monitor.
2Set POWER to VCR.
Power Lamp lights.
• If tape has no record tab, auto
playback begins.
• EVF or LCD monitor turns on/off by
the POWER switch.
• EVF shuts off when LCD monitor is
opened and turns back on when LCD
is closed.
3Playback function buttons.
AREW: Rewind tape.
BPLAY: Play tape.
CSTOP: Stop tape.
DBRIGHT:Adjust LCD monitor brightness.EVOLUME: Adjust volume of speaker, or
earphone
if connected.
Press “T” : Volume
up (+).
Press “W” :Volume
down (-).
3
Playback on EVF or LCD Monitor
Auto Tracking
Continuously analyzes each recording for
optimum picture quality.
Manual Tracking
Some recordings require manual
adjustment to reduce noise.
Press 
UP  or DOWN until Playback
picture clears up.
Press 
DISPLAY to return to Auto Tracking.
Speaker
MENU
UP
DOWN
DISPLAY
FOCUSFAR
NEAR
LCD-OPEN
BRIGHTD
PHONE
(earphone)
jack
T W
 VOLUME  +  VOLUME  + 
STOP
STILL
PLAY
REWFF
+
DEL
C
A
B
E
POWER  POWER 
REC REC
CAMERA
CAMERA
OFF OFF VCR VCRPHOTO PHOTO
Power Lamp
2