Panasonic Pv Gs83 Operating Instructions Manual

							Record mode
31LSQT1181
MagicPix function
This function allows you to record color subjects 
in dark locations to stand out against the 
background.
Attach the Camcorder to a tripod and you can 
record images free from vibration.
≥Recorded scene is seen as if frames were 
missed.
≥Set to Tape Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick up to select the MagicPix 
icon [ ].
≥The [MAGICPIX ON] indication appears on 
the screen of the Camcorder.
≥If it is difficult to focus, adjust the focus 
manually. (
-36-)
ªTo cancel the MagicPix functionSelect the [ ] icon again.
≥The [MAGICPIX OFF] indication appears on the 
screen of the Camcorder.
≥If set in a bright place, the screen may become 
whitish for a while.
≥The MagicPix function makes the signal 
charging time of the CCD up to approximately 
30k longer than usual, so that dark scenes (a 
minimum of 2 lx) can be recorded brightly. For 
this reason, bright dots that are usually invisible 
may be seen, but this is not a malfunction.
≥The MagicPix function is canceled when you 
turn off the power or operate the mode dial.
Soft skin mode
This allows the skin color to be recorded in a 
softer tone. This is more effective if you record a 
person closely from the torso up.
≥Set to Tape/Card Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick left to select the soft skin 
icon [ ].
≥The [SOFT SKIN MODE ON] indication 
appears on the screen of the Camcorder.
ª
To cancel the soft skin modeSelect the [ ] icon again.
≥The [SOFT SKIN MODE OFF] indication 
appears on the screen of the Camcorder.
≥If the background or anything else in the scene 
has colors similar to the skin color, they will also 
be smoothed.
≥If the brightness is insufficient, the effect may 
not be clear.
1
1
S5650.book  31 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
32LSQT1181
Fade in/fade out function
Fade inThe image and audio gradually appear.Fade outThe image and audio gradually disappear.
≥Set to Tape Recording Mode.1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.2Move the joystick left to select the fade icon 
[].
≥The [FADE ON] indication appears on the 
screen of the Camcorder.
3Press the recording start/stop button.
Start recording. (fade in) 
When you start recording, the image/audio 
disappears completely and the image/audio 
gradually appears.
Pause recording. (fade out) The image/audio gradually disappears. After the 
image/audio completely disappears, recording 
stops.
ª
To cancel fadingSelect the [ ] icon again.
≥The [FADE OFF] indication appears on the 
screen of the Camcorder.ª
To select the color for fade in/fade outThe color which appears in fading pictures can be 
selected.
1Set [ADVANCED] >> [FADE COLOR] >> 
[BLACK] or [WHITE].
≥While the fade in/fade out function is selected, it 
takes several seconds to display the image 
when you start recording images. Besides, it 
also takes several seconds to pause recording.
Wind noise reduction function
This reduces the wind noise coming into the 
microphone when recording.
≥
Set to Tape Recording Mode.1Set [BASIC] >> [WIND CUT] >> [ON].
ªTo cancel the wind noise reduction 
function
Set [BASIC] >> [WIND CUT] >> [OFF].
≥The default setting is [ON].
≥Reduces the wind noise depending on the wind 
strength. (If this function is activated in strong 
winds, the stereo effect may be reduced. When 
the wind weakens, the stereo effect will be 
restored.) 
1B
S5650.book  32 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
33LSQT1181
Self-timer recording 
You can record still pictures on a card using the 
timer.
≥Set to Card Recording Mode.
1Press the joystick to display the icon. Move 
the joystick down until icon 1 appears.
2Move the joystick left to select the self-timer 
recording icon [ ].
≥The [SELF-TIMER ON] indication appears on 
the screen of the Camcorder.
3Press the Photoshot button [ ].
≥After the [ ] indication flashes for approx. 
10 seconds, recording will start. After 
recording, the self-timer will be canceled.
ª
To stop the timer midway throughPress the [MENU] button.
≥The self-timer standby mode is canceled when 
you turn off the power or operate the mode dial.
Wide/4:3 function
This allows you to record images compatible with 
wide-screen TVs.
Wide Function
Images are recorded with a 16:9 aspect ratio.
4:3 Function
Images are recorded with a 4:3 aspect ratio.
≥Set to Tape/Card Recording Mode.
1Wide Function
Set [BASIC] >> [ASPECT] >> [16:9].
4:3 Function
Set [BASIC] >> [ASPECT] >> [4:3].
ª
To Cancel the Wide/4:3 FunctionWide Function
Set [BASIC] >> [ASPECT] >> [4:3].
4:3 Function
Set [BASIC] >> [ASPECT] >> [16:9].
≥The default setting is [16:9].
≥In the wide-screen mode, the menu screens, 
operation icons and other screen displays 
appear horizontally oriented.
≥When images are played back on a TV screen, 
the date/time indication may be erased in some 
cases.
≥Depending on the TV, the picture quality may 
deteriorate.
≥If still pictures recorded with a 4:3 aspect ratio 
are played back when [TV ASPECT] is set to 
[16:9], part of the operation icons and other 
displays will appear on the black bands on the 
left and right of the picture. 
≥Concerning the TV to be connected and TV 
used for playback
≥When playing back images taken by this unit 
on a TV screen, change the setting 
established by Tape/Card playback mode 
[SETUP] >> [TV ASPECT] to match the 
aspect ratio (4:3 or 16:9) of the TV monitor to 
be connected. (
-39-)≥Depending on the settings of the TV 
connected, the images may not be displayed 
properly. For more information, please read 
the operating instructions for the TV.
1
S5650.book  33 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
34LSQT1181
Optical image stabilizer function
This feature reduces the jitter caused by hand 
movement when recording.
≥Set to Tape/Card Recording Mode.
1Set [ADVANCED] >> [O.I.S.] >> [ON].
ª
To cancel the optical image stabilizer 
function
Set [ADVANCED] >> [O.I.S.] >> [OFF].
≥In the following cases, the optical image 
stabilizer function may not work effectively.
≥When the digital zoom is used
≥When the Camcorder is shaken greatly
≥When you record a moving subject while 
tracking it
Guideline function
View the slope and the balance of the image 
while recording.
You can check if the image is level while 
recording motion pictures. The function can also 
be used to estimate the balance of the 
composition.
≥Set to Tape/Card Recording Mode.
1Set [ADVANCED] >> [GUIDE LINES] >> 
[ON].
ª
To cancel the guideline functionSet [ADVANCED] >> [GUIDE LINES] >> [OFF].
≥The guide lines do not appear on the images 
actually recorded.
Recording in various situations 
(Scene mode)
When you record images in different situations, 
this mode automatically sets optimum shutter 
speeds and apertures.
≥Set to Tape/Card Recording Mode.
1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Set [BASIC] >> [SCENE MODE] >> select the 
desired mode.
1) [5] Sports mode
≥To record sports scenes or scenes where 
there are quick motions
2) [ ] Portrait mode
≥To make people stand out against the 
background
3) [ ] Low light mode
≥To make the scene brighter in dark 
conditions
4) [ ] Spotlight mode
≥To make the subject under a spotlight look 
more attractive
5) [ ] Surf & snow mode
≥To record images in bright places such as 
ski slopes and beaches
3)
1)
5)
2)
4)
S5650.book  34 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
35LSQT1181
ªTo cancel the scene mode functionSet [BASIC] >> [SCENE MODE] >> [OFF] or set 
the [AUTO/MANUAL/FOCUS] switch to [AUTO].
Sports mode
≥This mode reduces Camcorder shakes for the 
playback pause of recorded pictures.
≥During normal playback, the image 
movement may not look smooth.
≥Avoid recording under fluorescent light, 
mercury light or sodium light because the 
color and brightness of the playback image 
may change.
≥If you record a subject illuminated with strong 
light or a highly reflective subject, vertical 
lines of light may appear.
≥If the brightness is insufficient, the sports 
mode does not function. The [5] indication 
flashes.
≥If this mode is used indoors, the screen may 
flicker.
Portrait mode
≥If this mode is used indoors, the screen may 
flicker. If so, change the scene mode setting 
to [OFF].
Low light mode
≥Extremely dark scenes may not be able to be 
recorded finely.
Spotlight mode
≥If the recording subject is extremely bright, 
the recorded image may become whitish and 
the periphery of the recorded image 
extremely dark.
Surf & snow mode
≥If the recording subject is extremely bright, 
the recorded image may become whitish.
Recording in natural colors 
(White balance) 
The automatic white balance function may not 
reproduce natural colors depending on the 
scenes or lighting conditions. If so, you can adjust 
the white balance manually.
≥Set to Tape/Card Recording Mode.
1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Move the joystick up to select the white 
balance icon [ ].
3Move the joystick left or right in order to 
select the white balance mode.
1) Auto white balance adjustment [ ]
2) Indoor mode (for recording under 
incandescent lamps) [ ]
3) Outdoor mode [ ]
4) Manual adjustment mode [ ]
ª
To restore to the automatic 
adjustment
Move the joystick left or right until the [ ] 
indication appears. Or, set the [AUTO/MANUAL/
FOCUS] switch to [AUTO].
≥When the Camcorder is turned on with the lens 
cap attached, the automatic white balance 
adjustment may not function properly. Please turn 
the Camcorder on after removing the lens cap.
≥When setting both the white balance and the 
iris/gain, set the white balance first.
≥Whenever recording conditions change, re-set 
the white balance for correct adjustment.
MNL
11
11AW B
3) 1)
2)
4)
AWB
AWB
S5650.book  35 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
36LSQT1181
ªTo set the white balance manuallySelect [ ] in Step 3. Then, while viewing a white 
subject on the entire screen, move the joystick up 
to select the [ ] indication.
≥The white balance is set when the [ ] 
indication stops flashing.
ª
About flashing of the [ ] indicationWhen the manual adjustment mode is 
selected
≥Flashing indicates that the white balance 
previously adjusted is stored. This setting is 
stored until the white balance is adjusted again.
When white balance cannot be set in the 
manual adjustment mode
≥White balance may not be adjusted properly in 
the manual adjustment mode in dark places. If 
required, use the auto white balance mode.
Setting in the manual adjustment mode
≥When the setting is completed, it will keep lit.
ª
About the white balance sensorThe white balance sensor detects the type of light 
source during recording.
≥Do not cover the white balance sensor during 
recording or it may not function properly.
Manual focus adjustment
If auto focusing is difficult due to the conditions, 
then manual focusing is available.
≥Set to Tape/Card Recording Mode.
1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Set the [AUTO/MANUAL/FOCUS] switch to 
[FOCUS].
≥The [ ] indication and the manual focus [MF] 
indication appears.
3Move the joystick left or right in order to 
adjust the focus.
≥When focused with a wide angle, the subject 
may not be in focus when zoomed in. First, 
zoom in on the subject and then focus on it.
ª
To restore to the automatic 
adjustment
Set the [AUTO/MANUAL/FOCUS] switch to 
[AUTO] or [FOCUS].
MFMFMNL
MNL
MFMFMNL
S5650.book  36 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Record mode
37LSQT1181
Manual shutter speed/aperture 
adjustment
Shutter SpeedAdjust it when recording fast-moving subjects. ApertureAdjust it when the screen is too bright or too dark.
≥Set to Tape/Card Recording Mode.1Set the [AUTO/MANUAL/FOCUS] switch to 
[MANUAL].
2Move the joystick left or right to select 
aperture icon [ ] or shutter speed icon 
[] .
3Move the joystick left or right in order to 
adjust the shutter speed or aperture.
1) Shutter speed
2) (Aperture) Iris/gain value
ª
To restore to automatic adjustmentSet the [AUTO/MANUAL/FOCUS] switch to 
[AUTO].
Manual shutter speed adjustment≥Avoid recording under fluorescent light, mercury 
light or sodium light because the color and 
brightness of the playback image may change.
≥If you increase the shutter speed manually, the 
sensitivity lowers and accordingly the gain value 
increases automatically, which may increase 
the noise on the screen.
≥You may see vertical lines of light in the 
playback image of a brightly shining subject or 
highly reflective subject, but this is not a 
malfunction.≥During normal playback, image movement may 
not look smooth.
≥When recording in an extremely bright place, 
the color of the screen may change or flicker. If 
this happens adjust the shutter speed manually 
to 1/60 or 1/100.
Manual iris/gain adjustment≥Set the shutter speed before setting the 
aperture (iris/gain) when manually adjusting 
both settings.
≥If the value does not become “OPEN”, you 
cannot adjust the gain value.
≥If the gain value is increased, the noise on the 
screen increases.
≥Depending on the zoom magnification, there are 
iris values that are not displayed.
ª
Shutter speed range1/60 to 1/8000 seconds: Tape Recording Mode
1/60 to 1/500 seconds: Card Recording Mode
The shutter speed closer to 1/8000 is faster.
ª
Iris/gain value rangeCLOSE (Closed), F16, ..., F2.0,
OPEN (Opened: F1.8) 0dB, ..., 18dB
Value closer to [CLOSE] darkens the image. 
Value closer to [18dB] brightens the image.
Values with dB are gain values.
MNL
1/1000
MNL1)
1/60OPEN
OdB
MNL
1/60
F2.0
0dB
MNL2)
S5650.book  37 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Playback mode
38LSQT1181
Playback mode
Playing back tape
≥Set to Tape Playback Mode.
(An operation icon automatically appears on 
the LCD monitor.)
1Operate with joystick.
1/;: Playback/Pause
6: Rewind/Review playback (Reverts to 
playback with the 1/; icon.) 
5: Fast forward/Cue playback (Reverts to 
playback with the 1/; icon.) 
∫:Stop
≥The power will not turn off when the LCD 
monitor and the viewfinder are closed and 
retracted during Tape playback mode.
≥During cue/review playback, fast-moving 
images may show noise as a mosaic.
≥Before and after cue/review playback, the 
screen may become blue for a moment or 
images may be disturbed.ª
To adjust volumeAdjust the speaker volume for playback.1Move the [s/VOLr] lever to adjust the 
volume.
Towards [r]: increases the volume
Towards [`]: decreases the volume
(The nearer the bar is to [r], the higher the 
volume.) 
≥When the adjustment is completed, the volume 
indication will disappear.
≥If you do not hear the sound, check the settings 
of [SETUP] >> [12bit AUDIO].
ª
Repeat playbackWhen the tape end is reached, the tape will be 
rewound and played back again.
1Set [ADVANCED] >> [REPEAT PLAY] >> 
[ON]. 
≥The [ ] indication appears. (In order to 
cancel the repeat playback mode, set 
[REPEAT PLAY] >> [OFF] or turn off the 
power.)
ª
Settings on the audio≥If you cannot listen to the desired audio when 
playing back a tape, check the settings in 
[SETUP] >> [12bit AUDIO].
≥When you record the audio in [12bit] and set 
[SETUP] >> [12bit AUDIO] >> [MIX], the audio 
will be played back in stereo sound regardless 
of the settings in [AUDIO OUT].
PCVOL
S5650.book  38 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Playback mode
39LSQT1181
Frame-by-frame playback
≥Set to Tape Playback Mode.1During playback, move the joystick up to 
select the [1/;] icon to pause playback.
2Push the [s/VOLr] lever.
Towards [T]: normal direction
Towards [W]: reversed direction
≥If you keep pushing the lever, then the images 
will continuously be played back frame by 
frame.
≥The pause icon appears for an instant. 
Continuous frame-by-frame playback will start 
after the pause icon disappears.
ª
To return to normal playbackMove the joystick up to select the [1/;] icon to 
start playback.
Playback on TV
Images recorded by this Camcorder can be 
played back on a TV.
≥Insert a recorded tape or card into this 
Camcorder.
≥Be sure that the power of the unit is turned off 
before connecting it to a TV.
1Connect the Camcorder and a TV.
≥Connect the Camcorder and a TV by using 
the AV cable 1.
2Turn on this Camcorder and set the mode 
dial to the Tape Playback Mode (or Card 
Playback Mode).
3Select the input channel on the TV.
≥If the images are not played back correctly on 
the TV (e.g. they are displayed vertically), 
perform the menu operations in accordance 
with the aspect ratio of the TV monitor.
Set [SETUP] >> [TV ASPECT] >> [16:9] or 
[4:3].
4Move the joystick up to select the [1/;] 
icon to start playback.
≥The image and audio are output on the TV.
5Move the joystick down to select the [∫] 
icon to stop playback.
≥Use the AC adaptor to free you from worrying 
about the battery running down.
ª
If the image or audio from this 
Camcorder is not output on the TV
≥Check that the plugs are inserted as far as they 
go.
≥Check the [12bit AUDIO] settings. (
-56-)
≥Check the connected terminal.
≥Check the TV’s input setting (input switch). 
(For more information, please read the 
operating instructions for the TV.) 
VOL1
[VIDEO IN]
[AUDIO IN]
A/V
S5650.book  39 ページ  ２００６年１２月５日　火曜日　午前１０時５２分 
						

							Playback mode
40LSQT1181
Playing back card 
≥Set to Card Playback Mode.
(An operation icon automatically appears on 
the LCD monitor.)
1Operate with joystick.
E: Plays back the previous pictureD: Plays back the next picture
1/∫: Slide show (Plays back the still pictures 
on the card in order) start/pause
≥The power will not turn off when the LCD 
monitor and the viewfinder are closed and 
retracted during Card playback mode.
≥Even if the operation icon does not appear, the 
previous or next picture can be displayed.
≥While the data on a card are played back, do 
not operate the mode dial.
≥When the access lamp is lit, do not remove the 
card.
≥Depending on the picture size, it may take time 
to display the file.
≥If you attempt to play back file recorded in a 
different format or file data is defective, the 
whole display becomes bluish and the 
“UNPLAYABLE CARD’’ indication may appear 
as warning.
≥When playing back still pictures recorded in 4:3 
mode ( ) on a wide-screen TV, the picture 
quality may deteriorate.
≥When playing back a file recorded on other 
equipment, the date and time display is different 
from when it was recorded.ª
To display multiple playback filesMultiple files on the card (6 files on 1 screen) are 
displayed.
1Move the [s/VOLr] lever to switch the 
images.
Towards [r]: Full-screen display 
(Displays 1 image.) 
Towards [`]: Multi-screen display 
(Displays 6 files on 1 screen.) 
≥In the multi-screen display,
≥Move the joystick to select a file (The 
selected file will be encircled by an orange 
frame) and press to determine it. The 
selected file is full-screen displayed.
≥If there are 7 files or more, then move the 
joystick. The next or previous multi-screen 
will be displayed.
ª
About the compatibility of still 
pictures
≥The Camcorder is compliant with the unified 
standard DCF (Design rule for Camera File 
system) established by JEITA (Japan 
Electronics and Information Technology 
Industries Association).
≥The file format supported by this Camcorder is 
JPEG. (Not all JPEG formatted files will be 
played back.) 
≥If an out-of-specs file is played back, the folder/
file name may not be displayed.
≥The Camcorder may degrade or not play back 
data recorded or created on another brand of 
Camcorder and vice versa.
PC
0.3M
ø÷÷ô÷÷÷ø
S5650.book  40 ページ  ２００６年１２月５日　火曜日　午前１０時５２分