Panasonic Pv Gs36 Operating Instructions Manual

							Playback Mode
41
703-0809
12:34:56AM
JAN  2 2006      NO.  11
1Folder File Number
2Picture Size (p. 56)
3File Number
12
3
1  Push the [–  / VOL +] Lever to switch the 
images.
To Select a Desired File and Playing 
Back
Multiple files on the card (6 files on 1 screen) are 
displayed.
Towards [+] : Full-screen display
(Displays 1 image.)
Towards [–] : Multi-screen display
(Displays 6 files on 1 screen.)
NO.5     100-0012
1File Number
2Folder File Number
12
2  Move the Joystick Control [▲, ▼, ◄, or ►] 
to select a desired fi le.
•  In the Multi-screen display,
-  Move the Joystick Control [▲, ▼, ◄, or ►] to 
select a file (The selected file will be encircled by 
a yellow frame) and press to determine it. The 
selected file is full-screen displayed.
-  If there are 7 files or more, then move the 
Joystick Control. The next, or previous 
Multi-Screen will be displayed.
„ About the compatibility of still pictures•  The Camcorder is compliant with the unified 
standard DCF (Design rule for Camera File 
system) established by JEITA (Japan Electronics 
and Information Technology Industries 
Association).
•  The file format supported by this Camcorder 
is JPEG. (Not all JPEG formatted files will be 
played back.)
•  If an out-of specs file is played back, the folder/
file name may not be displayed.
•  The Camcorder may degrade or not play back 
data recorded or created on another product and 
another product may degrade or not play back 
data recorded on the Camcorder.
Notes:•  While the data on a card are played back, do not 
operate the Mode Dial.
•  If a blank (nothing recorded) Card is played, the 
screen becomes white.
•  If you attempt to play back file recorded in a 
different format or file data is defective, the whole 
display becomes bluish and the [UNPLAYABLE 
CARD] Indication may appear as warning.
•  When the Access Lamp is lit, do not insert or 
remove a card.
•  When playing back a picture recorded on other 
equipment, its size and that of this Camcorder may 
appear differently.
•  It takes time to display the file depending on the 
number of pixels of the file.
•  When playing back a file recorded on other 
equipment, the date and time display is different 
from when it was recorded.
•  When playing back a picture recorded on other 
equipment, the picture may not be played back or 
the quality of pictures may be deteriorated.
•  When playing back a non standardized file, the 
Folder File Number may not be displayed.
  Slide Show
The recorded still pictures in the Card can be played 
back like a Slide Show.
•  Set to Picture Playback Mode.•  The One-Touch Navigation icon is displayed on the 
lower right of the screen.
1  Move the Joystick Control [▲] to select 
[  ].[One-Touch Navigation icon] 
						

							42For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
3  Move the Joystick Control [▲] or [▼] to 
select [DELETE 1 FILE] and press the 
Joystick Control.
To Select and Delete All Files
•  The selected file is deleted from the Card.
•  If [NO] is selected, the file selection is 
canceled.
4  Move the Joystick Control [▲] or [▼] 
to select [YES] and press the Joystick 
Control.
1  Move the Joystick Control [▼] to select 
[  ].
2  Move the Joystick Control [▲] or [▼] to 
select [ALL FILES] and press the Joystick 
Control.
2  Move the Joystick Control [▼] to select 
[  ].
•  All files of Picture Playback Mode are erased.
•  A locked file cannot be erased.
3  Move the Joystick Control [▲] or [▼] 
to select [YES] and press the Joystick 
Control.
[One-Touch Navigation icon]
DELETE
SETUP   ENTER    EXIT
ALL FILES
DELETE 1 FILE
NOOK TO DELETE IMAGE?
DELETE
SETUP   ENTER    EXIT
YES
NO
DELETE THIS IMAGE?
[One-Touch Navigation icon]
DELETE
SETUP   ENTER    EXIT
ALL FILES
DELETE 1 FILE
NOOK TO DELETE IMAGE?
DELETE
SETUP   ENTER    EXIT
YES
NO
DELETE ALL IMAGES?
703-0809
12:34:56AM
JAN  2 2006      NO.  11
• The [  ] Indication is displayed.
•  Each of the pictures are played back for 
several seconds.
„ To Stop the Slide ShowMove the Joystick Control [▲] to select [  ] 
again.
Deleting the Files Recorded on a 
Card
Using the Camcorder, you can delete the files 
recorded on a Card. After the file is deleted, it cannot 
be restored.
•  Set to Picture Playback Mode.•  The One-Touch Navigation icon is displayed on the 
lower right of the screen.
To Select and Delete Files
1  Move the Joystick Control [◄] or [►] to 
select the fi le to be deleted.
Note:•  Playback time may take longer than usual 
depending on the picture.
[One-Touch Navigation icon]
„ Deleting still picture files recorded on a 
card by other equipment
•  A still picture file (other than JPEG) that cannot 
be played back on the Camcorder may be 
erased.
•  To delete multiple files on the SD Card (selected 
files) connect to a PC and use the SD Drive 
feature. 
						

							Playback Mode
43
Writing Printing Data on a Card 
( DPOF Setting)
DPOF Setting Printing data (DPOF Settings), such 
as the number of images to be printed, can be written 
to the Card. “DPOF” means Digital Print Order 
Format.
•  Set to Picture Playback Mode.•  The One-Touch Navigation icon is displayed on the 
lower right of the screen.
1 Set [  ADVANCED] >> [  DPOF SET] >> 
[SET].
•  When all images are not printed, select 
[CANCEL ALL].
DPOF SET
SETUP   ENTER    EXIT
DPOF SET
SETUP   ENTER    EXIT2
2
„ About the DPOFDPOF stands for Digital Print Order Format. This 
enables the printing information to be added to the 
pictures on the card so that it can be used on a 
system supporting DPOF.
4  Repeat Steps 2 and 3 and press the 
[MENU] Button when the setup is 
completed.
Notes:
•  DPOF setting made on another camera may not 
be recognized by Camcorder. Perform the DPOF 
Settings on your Camcorder.
•  Verifying the DPOF Settings may take a little time. 
Wait until the Card Access Lamp goes out.
•  The number of prints 
2 is displayed in the 
picture set.
•  You can select from 0 to 999. (Selected 
number of pictures can be printed as you set 
the number of prints with the printer supporting 
DPOF.)
•  2 or more files can be set in succession.
2  Move the Joystick Control [▲, ▼, ◄, or ►] 
to select a desired picture and press the 
Joystick Control.
•  The selected picture is marked with a frame.
•  The number of prints 1 set to be in DPOF is 
displayed.
3  Move the Joystick Control [▲] or [▼] to 
select the number of prints, and press the 
Joystick Control.
1
2
Protecting the Files on a Card 
( Lock Setting) 
Precious files recorded on a Card can be locked to 
prevent accidental erasure. (Even if files are locked, 
the files will be deleted if the Card is formatted.)
•  Set to Picture Playback Mode.•  The One-Touch Navigation icon is displayed on the 
lower right of the screen.
1 Set [  BASIC] >> [  PROTECT] >> [YES].
•  The selected file is locked and the [  ] 
Indication 1 appears. Repeat this procedure to 
lock 2 or more files.
•  Press the Joystick Control again to cancel.
2  Move the Joystick Control [▲, ▼, ◄, or ►] 
to select the fi le to be locked, and press 
the Joystick Control.
3  Repeat Step 2 and press the [MENU] 
Button when the setup is completed.
Notes:•  The Lock Setting carried out by this Camcorder is 
only effective for this Camcorder.
•  The SD Memory Card has a write protection switch 
on it. If the switch is moved to the [LOCK] side, you 
cannot write to or format the Card. If it is moved 
back, you can.
PROTECT
SETUP   ENTER    EXIT
PROTECT
SETUP   ENTER    EXIT
1
Notes:•  Do not turn off the power while deleting.
•  To delete files, use the AC Adapter or a sufficiently 
charged battery.
•  In case of [ALL FILES], the deletion may take time 
if there are many files on the card.
•  When [CARD FULL] is shown during recording, 
switch to the Picture Playback Mode and then 
delete unnecessary files.
•  If files conforming to DCF standard are deleted, all 
the data related to the files will be deleted. 
						

							44For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
A/V
Playing Back on Your TV
By connecting your Camcorder with your TV, the 
recorded scenes can be viewed on your TV screen.
•  Before connecting them, turn off the power of both 
the Camcorder and TV.
1  Insert a recorded tape into this 
Camcorder.
2  Connect the [AV OUT] Jack of the 
Camcorder and the Video and Audio Input 
Jacks of the TV.
•  Connect to the TV with the AV Cable 1.
[VIDEO IN]
[AUDIO IN]
1
3  Turn on this Camcorder and set the Mode 
Dial to the Tape Playback Mode.
4  Select the input channel on the TV.
5  Move the Joystick Control [▲] to 
select the [  ] to start playback.•  The image and audio are output on 
the TV.
6  Move the Joystick Control [▼] to select 
the [  ] to stop playback.
„ If the image or audio from this 
Camcorder is not output on the TV
•  Check that the plugs are inserted as far as they 
go.
•  Check the [12bit AUDIO] settings.
•  Check the connected terminal.
•  Check the TV’s input setting (input switch). (For 
more information, please read the operating 
instructions for the TV.)
Note:•  Use the AC adaptor to avoid battery depletion. •  When the formatting is completed, the screen 
becomes gray.
Notes:•  Normally, it is not necessary to format the card. If 
a message appears even though you insert and 
remove the card several times, format it.
•  In order to maintain full compatibility, you must 
format the SD Memory Card using the Camcorder.
•  PC formatted SD Memory Cards are not compatible 
with the Camcorder.
•  The Camcorder supports SD Memory Cards 
formatted in FAT12 system (for SD Memory Card 
of 8, 16, 32 and 64 MB) and FAT16 system (for 
SD Memory Card of 128, 256, 512 MB, 1 GB and 
2 GB).
  Formatting a Card
If a Card becomes unreadable by the Camcorder, 
format it for reuse. Formatting erases all the data 
recorded on a Card.
•  When formatting the card all protected files 
(lock) are also deleted.
•  Set to Picture Playback Mode.•  The One-Touch Navigation icon is displayed on the 
lower right of the screen.
1 Set [  ADVANCED] >> [  FORMAT 
CARD] >> [YES].
•  A confirmation message appears, select [YES] 
and formatting will be carried out.
FORMAT CARD
SETUP   ENTER    EXIT
YES
NODELETES ALL DATA 
						

							Editing Mode
45
Editing Mode
A/V
[VIDEO IN]
[AUDIO IN]
1
Copying onto a DVD Recorder or 
a VCR ( Dubbing)
Pictures recorded by the Camcorder can be stored on a DVD-RAM or other such media. Refer to the 
instructions for the recorder.
•  Place a recorded cassette in the Camcorder, 
and an unrecorded DVD-RAM or cassette in 
the DVD Recorder or VCR.
1  Connect the Camcorder and the Recorder.
„ Connecting with the AV Cable
•  Connect the Camcorder and the Recorder by 
using the AV Cable 1.
„ Connecting with the optional DV 
cable (Only for equipment with a DV 
terminal)
2  Turn on the Camcorder and set to Tape 
Playback Mode.
3  Select the input channel on the TV set and 
recorder.
4  Move the Joystick Control 
[▲] to start playback.
•  The image and sound are 
reproduced.
[One-Touch Navigation icon]
5 Start recording.
6  Move the Joystick Control [▼] to stop 
playback.
7 Stop recording.
•  For more information, refer to the operating 
instructions for your TV set and recorder.
„ When neither image nor sound from 
the Camcorder is output to the TV set
•  Check that the plugs are inserted as far as they 
go.
•  Check the [12bit AUDIO] settings.
•  Check the connected terminal.
     SP 3h59m59s29f
                  R 2:00
12:34:56AM
JAN  2 2006  100
Using the DV Cable for Recording 
(Digital  Dubbing)
Player/Recorder:
2  Insert the Cassette and set to Tape 
Playback Mode.
Player:
3  Move the Joystick Control [▲] to start 
playback.
Recorder:
4 Set [  ADVANCED] >> [  REC STDBY] 
>> [YES], then move the Joystick Control 
[▲] to select [ 
 ].• Recording starts. By connecting this Camcorder with other digital video 
equipment (such as another Camcorder of the same 
format/model) that has a DV input/output Terminal, 
and using a 4-pin to 4-pin DV Interface Cable 
PV-DDC9 (optional) 
1, high quality images and 
sounds can be dubbed in the digital mode.
•  Set to Tape Playback Mode (Player/Recorder)
1  Connect the Camcorder and digital video 
equipment with the DV cable.
1 
						

							46For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at: http://www.panasonic.com/contactinfo
CAUTION:
Unauthorized exchanging and/or copying 
of copyrighted recordings may be copyright 
infringement.
„ To Stop DubbingMove the Joystick Control [▲] to select [  ] 
again.
„ To Cancel the Standby for RecordingWhen the Camcorder is on standby for recording, 
move the Joystick Control [▼] and select the [  ].
Notes:•  Do not plug or unplug the DV Cable during 
dubbing, or the dubbing may not be completed 
properly.
•  If a picture (bilingual video, etc.) containing main 
sound and sub sound has been dubbed, select the 
desired sound by [ 
 SETUP] >> [  AUDIO OUT] 
on playback.
•  Regardless of the menu settings on the recorder, 
digital dubbing is carried out in the same mode as 
the [ 
 AUDIO REC] mode of the playback tape.
•  The images on the recorder monitor may be 
disturbed, but it does not affect the recorded 
images.
•  Even if you use a device equipped with DV 
Terminals such as IEEE1394, you may not be able 
to perform Digital Dubbing in some cases. For more 
information, see the instructions for equipment 
connected.
•  Date or other information to be displayed cannot 
be displayed if the software of the connected 
equipment does not support the display function.
•  While pictures are input from the DV terminal, the 
One-Touch Navigation icon blinks on instead of 
appearing from the side of the screen when you 
press the center of the Joystick Control.
PC Connection With DV Interface 
Cable
A video clip can be transferred directly to your PC 
(Personal Computer) via a DV Interface Cable 
(Optional) using products and software from a 
number of video editing software companies.
Using products from video editing software 
companies allows you to capture and edit video clips 
using the DV Interface.
Our DVC being OHCI compliant should 
have no problem working with any OHCI 
compliant Firewire Card/video - Editing 
software package.
•  Personal Computer must be equipped with an DV 
Terminal.
•  During Camcorder playback, do not disconnect the 
DV Interface Cable or turn the Camcorder off as 
this may cause a PC hang-up error.
•  1394 (i.LINK) Interface must conform to OHCI 
(Open Host Controller Interface Specification).
Recording from a Tape onto a Card
Still pictures can be recorded on the Memory Card 
from scenes that have already been recorded on a 
cassette.
1  Set the Mode Dial to Tape Playback Mode.•  The One-Touch Navigation icon is displayed 
on the lower right of the screen.
3  Move the Joystick Control [▲] to start 
playback and set the Camcorder to Still 
Playback Mode at the scene you wish 
to record, and press the [PHOTO SHOT] 
Button.
Note:•  If you press the [PHOTO SHOT] Button without 
pausing, blurred pictures may be recorded.
[One-Touch Navigation icon]
2  Insert a tape which already has recorded 
contents and a card.
•  Audio will not be recorded. 
						

							With a PC
47
Using Camcorder with a PC
An image stored on the DV Cassette or Memory 
Card can be transferred to your personal computer.
Software Installation (For Windows)
•  If you have Internet access, please download the 
USB Driver.
With a PC
1  To download and install the Driver, go to:http://www.panasonic.com/consumerdownloads
„ USB Driver (pp. 47~48)When the Camcorder is connected to your PC, 
you can send video from your Camcorder to other 
parties via a network or the Internet.
2  Click the software to be downloaded.
Using the USB Function 
The USB connection can be used in one of the 
following two ways.
1  In PC Mode, with the PC connected, the SD drive can be used (p. 48).2  In Tape Recording or Tape Playback Mode, with 
the PC connected, a motion image can be used 
(pp. 50~53).
•  Check your OS in the Operating Environment 
section on page 47 and if necessary, install the 
USB Driver before using the USB function.
Operating environment
•  Despite having the Operating environment 
indicated, it may not be possible to use the program 
with some types of personal computers.
•  When you connect to an USB 2.0 interface 
board, use a certified board with the USB 2.0 
(FULL-SPEED USB) logo.
„ For  WindowsOS:1 Function:
IBM PC/AT compatible personal computer with 
pre-installed:
Microsoft Windows XP Professional/Home Edition
Microsoft Windows 2000
•  The USB equipment operates with the driver 
installed standard on your OS.
2 Function:
•  This is the Operating environment for the USB 
Driver which can be installed from the Web Site.IBM PC/AT compatible personal computer with 
pre-installed:
Microsoft Windows XP Professional/Home Edition 
SP2 or later
Microsoft Windows 2000 SP4 or later
•  For Windows 2000 users:
Please download and install the USB Driver from 
the Web Site.
•  For Windows XP SP2 users:
The USB equipment operates with the driver 
installed standard on your OS.
CPU:Intel Pentium ll 300 MHz or higher 
(including compatible CPU)
RAM:32 MB or more (64 MB or more recommended)Free hard disk space:At least 30 MB or moreInterface:USB 1.1 or more - A Type
„ For  MacintoshOS:Mac OS X v 10.1 – X v 10.4
(Function 1 Only)CPU:Power PC G3 (400 MHz or higher), G4, G5RAM:64 MB or more
•  The USB equipment operates with the driver 
installed standard on your OS.
•  For Windows XP users, the USB equipment 
operates with the driver installed standard on your 
OS.
•  If you have Internet access, please download the 
USB Driver.
1  To download and install the Driver, go to:http://www.panasonic.com/consumerdownloads
Installing the USB Driver
2  Click [Camcorder] on the screen.
3  Click [USB Driver (for Web Camera)].
4  Decompress the downloaded data.
5 Double click  icon.•  The set up program starts running.
6  Finish installation by following the 
on-screen instructions.
•  Click [Next] and proceed with installation.
•  After completing the installation, click [Finish]. 
						

							48
By connecting the Camcorder and Personal 
Computer with the USB Cable, you can transfer still 
images saved on a Memory Card directly to your 
Personal Computer.
1  Insert the Memory Card into the 
Camcorder.
2  Set the Camcorder to PC Mode.
3  Connect the Camcorder to your personal 
computer with USB Cable and turn the 
Camcorder to “ON”.
•  It enters PC Connecting Mode.
•  Appropriate driver to recognize Camcorder is 
automatically installed by Windows Plug and 
Play when connected for the first time.
Using Built-in SD Drive
• Never connect the USB Cable until the USB 
Driver is installed.
•  Before making these connections, turn off all 
devices, which are to be connected.
•  It is recommended that you use the AC Adaptor as 
the power supply of the Camcorder.
Connecting the Personal Computer and
Camcorder
7  After the USB Driver is installed, please 
restart your computer.
„ For  WindowsOS:Microsoft Windows XP Professional/Home Edition
Microsoft Windows 2000
1
2
[Windows 2000] [Windows XP]
4  Open [My Computer] and click [Removable 
Disk] 1 (For Windows 2000 users).
5  Click [Open folder to view fi les using 
Windows Explorer] 2 and then [OK] (For 
Windows XP users).
•  After the USB Connection Cable is connected to 
the Camcorder, open [My Computer] or [Windows 
Explorer] to check that the drive is displayed as a 
removable disk drive (only when card is inserted 
into the Camcorder). It enables you to operate it in 
the same way as a floppy disk drive, and you can 
use the same drag and drop or copy methods.
•  You can view images stored on the Memory Card 
and also save them to your hard disk.
•  Please do not change file or folder names on the 
Personal Computer. The images on the Memory 
Card may not be able to be viewed on the 
Camcorder.
1  Insert the Memory Card into the 
Camcorder.
2  Set the Camcorder to PC Mode.
3  Connect the Camcorder to your Macintosh 
with USB Cable.
„ For  MacintoshOS:Mac OS X v 10.1 – X v 10.4
4  Double click the “NO_NAME” icon.•  You can view images stored on the Memory 
Card and also save them to your hard disk.
•  Please do not change file or folder names on 
the Personal Computer. The images on the 
Memory Card may not be able to be viewed on 
the Camcorder. 
						

							With a PC
49
To disconnect USB cable safely
„ For  WindowsIf USB Cable is disconnected while computer is 
on, error dialog may appear. In such case click 
[OK] and close the dialog box. By following the 
steps below you can disconnect the cable safely.
1  Double click the  icon in task tray.•  Hardware disconnect dialog appears.
Note on the driver name displayedThe driver name displayed will differ depending on 
your OS, operating environment and the mode of the 
Camcorder.
Windows XP/2000:•  When the Camcorder is in PC Mode:
[USB Mass Storage Device] or [Matshita DVC USB 
Device]
•  Make sure Camcorder’s Card Access lamp is off 
and disconnect the cable.
•  You can safely disconnect the cable.
3  Verify [Matshita DVC USB Device] is 
selected and click [OK].
2  Select [USB Mass Storage Device] and 
click [Stop].
CAUTION:
If you disconnect the USB Cable while the 
Card Access Lamp is on, it may damage the 
Card data.
Even when the following operations are performed, 
the same results will occur as when the USB Cable is 
removed (above). Therefore, it is imperative that the 
above operation 
1 is completed before proceeding.
•  When Camcorder power is turned OFF.
•  When SD Memory Card is removed.
•  When Mode Dial is turned to change modes.
Removing the USB Cable safely for 
Macintosh
1 Drop the [NO_NAME] icon which appeared 
when you connected the Camcorder with 
the USB Cable into the recycle bin, then 
disconnect the USB Cable.
„ For  Macintosh
If the above operation is not performed correctly, 
when data is copied from the personal computer 
to an SD Memory Card, the copied data may be 
damaged. 
						

							50
Using as a  Web Camera
If the Camcorder is connected to your personal 
computer, you can send video and sound from the 
Camcorder to the other parties via the network.
• Do not connect the USB Cable until the USB 
Driver is installed. (pp. 47~48)
OS:IBM PC/AT compatible personal computer with 
preinstalled;
Microsoft Windows XP Home Edition/Professional 
SP2*
1 or later
Microsoft Windows 2000 Professional SP4 or later
CPU:Intel Pentium lll 450 MHz or higher
(including compatible CPU)
RAM:128 MB or more (256 MB or more recommended)Free hard disk space:At least 250 MB or moreInterface:USB 1.1 or more - A TypeTo use the Camcorder as a Web Camera, the 
additional minimum requirements must be 
met.
Graphic display:
High Color (16 bit or more)
Desktop resolution of 800 × 600 pixels or more
Communication Speed:56 kbps or faster is recommended.Necessary software:Windows Messenger 5.0/5.1 (Windows XP)
MSN Messenger 7.0/7.5 (Windows XP/2000)
*1  When your OS is Windows XP SP2, the USB 
Driver is not needed.
Other requirements (to send/receive audio):Sound card
Speaker or headphones
To use the Camcorder as a Web Camera, the 
following conditions must be met.
•  To upgrade Windows XP to SP2 or later, click 
[Start] >> [All Programs] >> [Windows Update]. 
(Requires Internet connection.)
•  To upgrade Windows 2000 to SP4 or later, click 
[Start] >> [All Programs] >> [Windows Update]. 
(Requires Internet connection.)
Operating environment
•  You have direct dial-up connection capability to the 
Internet. Also, you and the other person(s) are in 
the same Network (LAN).
•  Install Windows Messenger (Windows XP). If you 
have a version older than 5.0/5.1, download the 
latest version (5.0/5.1) from the Microsoft Home 
Page.
The latest version of MSN Messenger can also be 
downloaded from the Microsoft Home Page.
http://www.microsoft.com/
(For download and installation instructions, please 
refer to Help on the Home Page.)
•  If you are connected to the Internet through a 
firewall or a router, proper communication will not 
be possible.
1  Install the USB Driver. (pp. 47~48)
2  Set the Camcorder to Tape Recording 
Mode or Tape Playback Mode.
•  To send the live camera picture to a PC, set 
the Camcorder to Tape Recording mode.
•  To send pictures recorded on a tape to a PC, 
set the Camcorder to Tape Playback mode.
Connecting the Camcorder to Personal
Computer (For Using as a Web Camera)
• When the Camcorder and personal computer 
(with Windows 2000) are connected via 
USB Cable, a message, such as the one 
below, is displayed. However, testing by the 
manufacturer has confirmed functionality of 
this Camcorder with Windows 2000. Click [Yes] 
and proceed.
3  Connect the Camcorder to your personal 
computer with USB Cable.
• The [  ] is displayed on the screen.
[Send] [Receive] [Software]
Windows XP← OK →Windows XPWindows 
Messenger/
MSN 
Messenger
Windows XP← OK →Windows 2000MSN 
Messenger
Windows 
2000← OK →Windows 2000MSN 
Messenger Please see chart below.