Panasonic Pv Gs29 Operating Instructions Manual
Have a look at the manual Panasonic Pv Gs29 Operating Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
21 Before Using • The power will not turn off if the LCD Monitor is closed and the Viewfinder is retracted. • The [STATUS] Indicator 2 automatically goes off and the power turns off. (If Quick Start is set to [ON] (p. 34), the unit goes into Quick Start standby mode and the [STATUS] Indicator lights Green.) • Even if the LCD Monitor is closed or the Viewfinder is retracted while recording on a tape, the power does not turn off. (The Viewfinder stays lit up.) 3 Open the LCD Monitor or extend the Viewfi nder again. • The [STATUS] Indicator lights Red and turn on the power. Setting Date and Time 1 Set [ BASIC] >> [ CLOCK SET] >> [YES]. CLOCK SET JAN .01.2006 12:00AM SETUP SET ENTER EXIT • Set to Tape/Card Recording Mode. (PV-GS39/ PV-GS59)(PV-GS29) SETUP ENTER EXIT YES NOSET DATE AND TIME When the Camcorder is turned on for the first time, [SET DATE AND TIME] will appear. Select [YES] and set the date and time. • If the screen shows the incorrect Date/Time, then adjust it.• If the built-in battery is weak, the [ ] Indication flashes. In this case, charge the built-in battery. • The clock uses the 12-hour system. 2 Move the Joystick Control [◄] or [►] to select the item to be set. Then move the Joystick Control [▲] or [▼] to set the desired value. • Year will cycle in the order shown below. 2000, 2001, ..., 2089, 2000, ... „ About Date/Time• The Date and Time function are driven by a built-in lithium battery. • Make sure to check the time before recording because the built-in clock is not very accurate. „ Recharging the built-in lithium batteryIf [ ] or [--] is appears when the Camcorder is turned on, then the built-in lithium battery has run down. Use the steps below to charge the battery. When the battery is inserted for the first time after charging, [SET DATE AND TIME] will appear. Select [YES] and set the date and time. Connect the AC adaptor to the Camcorder or place the battery on the Camcorder, and the built-in lithium battery will be recharged. Leave the camera as is for approx. 24 hours, and the battery will drive the date and time for approx. 6 months. (Even if the [OFF/ON] Switch is set to [OFF], the battery is still being recharged.) Using the Viewfinder/ LCD Monitor Before using the Viewfinder, adjust the field of view so that the displays inside the Viewfinder become clear and easy to read. 1 Pull the Viewfi nder. Using the Viewfinder • The Viewfinder will be activated. 2 Adjust by turning the Eyepiece Corrector Knob. • You can adjust the brightness of the Viewfinder from the Menu. 3 Press the Joystick Control to fi nish setting the date and time. • The clock operation starts from [00] second.
22 2 Adjust the LCD Monitor angle according to the desired recording angle. • The LCD Monitor can rotate a maximum of 180° 1 from the vertical position upwards and a maximum of 90° 2 to the downward direction. Forcefully rotating the LCD Monitor beyond these ranges will damage the Camcorder. „ Closing the LCD MonitorPush the LCD Monitor until it is securely locked. • Make sure the Card Slot Cover is closed. 1180°290° • The brightness and color level of the LCD Monitor can be adjusted from the Menu. • If it is forcibly opened or rotated, the Camcorder may be damaged or fail. • Check that the Card Slot Cover is closed before closing the LCD Monitor. • If the LCD Monitor is rotated by 180° towards the lens and the Viewfinder is opened (when recording yourself), the LCD Monitor and the Viewfinder simultaneously light. When [ LCD SET] or [ EVF SET] on the [ SETUP] Sub-Menu is set to [YES], the following items are displayed. [ LCD SET] LCD Brightness [ ]Adjusts the brightness of the image on the LCD screen. [ LCD SET] LCD Color Level [ ]Adjusts the color saturation of the image on the LCD screen and the Viewfinder. [ EVF SET] Brightness of the Viewfinder [ ]Adjusts the brightness of the image in the Viewfinder. „ To AdjustMove the Joystick Control [▲] or [▼] and select the item to be adjusted, and then move the Joystick Control [◄] or [►] to raise or lower the number of vertical bars in the Bar Indication. • More vertical bars indicates stronger brightness or color saturation. • Press the [MENU] Button or the Joystick Control to complete the settings. Adjusting Brightness and Color Level LCD SET SET SETUP ENTER EXITEVF SET SET ENTER EXIT Notes:• In order to adjust the brightness of the Viewfinder, close the LCD Monitor, and the Viewfinder will be activated. • When the LCD Monitor is rotated by 180° towards the lens, the brightness of the LCD Monitor cannot be adjusted. • These settings will not affect the images actually recorded. With the LCD Monitor open, you can also record the picture while watching it. 1 Place your Thumb on the [OPEN] Knob and pull the LCD Monitor out in the direction of the arrow. • The LCD Monitor will be activated. • It can open up to 90°. Using the LCD Monitor
23 Before Using Joystick Control and Screen Display Press the center of the Joystick Control, and the One-Touch Navigation icon will be displayed on the lower right of the screen. • Press the Joystick Control again to turn off the One-Touch Navigation icon. • Pressing the center button of the Joystick Control again to redisplay the One-Touch Navigation icon will display the last page used. Each press of [▼] switches the display as follows depending on the mode. 1/4 NEXT One-Touch Navigation icon OFF Press Center Press ▼ 2/4 NEXT 3/4 NEXT 4/4 NEXT Move the Joystick Control [▲, ▼, ◄, or ►] to select an item. • In the Tape Playback Mode or the Picture Playback Mode, the One-Touch Navigation icon will be automatically on the lower right of the screen. e.g., Tape Recording Mode [AUTO] Easy to Use Mode Dial You can choose a desired mode by rotating the Mode Dial. 1 Rotate the Mode Dial.• Set your desired mode to 1. :Tape Recording ModeUse this mode when recording pictures on a tape. :Tape Playback ModeUse this mode when playing back the recorded scene on a tape. :Card Recording Mode (For PV-GS39/PV-GS59) Use this mode when recording still pictures on a card. :Picture Playback Mode (For PV-GS39/PV-GS59) Use this mode when playing back the recorded still picture on a card. :PC Mode (For PV-GS39/PV-GS59)Use this mode when you want to connect the Camcorder to your Personal Computer. You can view or edit the images recorded on a card on your personal computer. How to Use the Joystick Control Basic Joystick Control Operations Operations on the menu screen and selection of files to be played back on the multi-image display. Move the Joystick Control [▲,▼,◄, or ►] to select an item or file, and then press in the center to set it. 1Select by moving [▲]. 2Select by moving [►]. 3Select by moving [▼]. 4Select by moving [◄]. 5Push the center to select the item. 5 1 2 3 4 Joystick Control (See below) One-Touch Navigation icon (PV-GS39/ PV-GS59)(PV-GS29) 11
24 „ Card Recording Mode (For PV-GS39/PV-GS59) • When the [AUTO/MANUAL/FOCUS] Switch is set to [AUTO]. 1/2◄ Self-timer Mode p. 35 ► Help Mode* p. 25 ▲ Backlight compensation p. 37 ▼Go to next page. – 2/2◄ Soft Skin Mode p. 38 ▼Go to next page. – 1/2 NEXT2/2 NEXT „ Tape Recording Mode• When the [AUTO/MANUAL/FOCUS] Switch is set to [FOCUS]. 5/6 NEXTIRISSHTRWB 2/3 NEXTIRISSHTRWB 1/6 NEXT 1/3 NEXT 2/6 NEXT3/6 NEXT 4/6 NEXT6/6 NEXT MF –MF + 3/3 NEXT MF –MF + 6/6◄ Manual Focus Adjustment Modep. 44 ► Manual Focus Adjustment Modep. 44 ▼Go to next page. – „ Card Recording Mode (For PV-GS39/PV-GS59) • When the [AUTO/MANUAL/FOCUS] Switch is set to [MANUAL]. 1/3 NEXT2/3 NEXT3/3 NEXTIRISSHTRWB 3/3◄ Manual Iris Adjustment Modep. 43 ► Manual Shutter Speed Adjustment Modepp. 42~43 ▲ Manual White Balance Adjustment Modepp. 41~42 ▼Go to next page. – „ Tape Recording Mode• When the [AUTO/MANUAL/FOCUS] Switch is set to [MANUAL]. 5/5 NEXTIRISSHTRWB 1/5 NEXT 2/2 NEXTIRISSHTRWB 1/2 NEXT 2/5 NEXT3/5 NEXT 4/5 NEXT 5/5◄ Manual Iris Adjustment Modep. 43 ► Manual Shutter Speed Adjustment Modepp. 42~43 ▲ Manual White Balance Adjustment Modepp. 41~42 ▼Go to next page. – „ Tape Recording Mode• When the [AUTO/MANUAL/FOCUS] Switch is set to [AUTO]. 1/4◄ Fade p. 37 ► Help Mode* p. 25 ▲ Backlight compensation p. 37 ▼Go to next page. – 2/4◄ Soft Skin Mode p. 38 ▼Go to next page. – 3/4▲ MagicPix Mode p. 38 ▼Go to next page. – 4/4◄ Recording Check p. 31 ► Blank Search Mode p. 31 ▼Go to next page. – 1/4 NEXT2/4 NEXT3/4 NEXT4/4 NEXT 1 • 1 is displayed while recording on a tape. 1 • 1 is displayed while recording on a tape. 1 • 1 is displayed while recording on a tape.
25 Before Using • Set to Tape/Card Recording Mode.You can view function help information using One-Touch Navigation. 1/4 NEXT [One-Touch Navigation icon] *Help Mode 1 Press the Joystick Control to display the One-Touch Navigation icon on the lower right of the screen. 2 Move the Joystick Control [▼] until the page with [ ] indication is displayed. e.g. 3 Move the Joystick Control [►] to select [ ]. 4 Move the Joystick Control [▲▼◄►] to select the desired function. e.g. SET EXIT BACKLIGHT COMPENSATIONPREVENTS DARK SUBJECTS IN BACKLIGHT 1/4 NEXTEXIT e.g. „ To end the Help ModeMove the Joystick Control [►] to select [EXIT] or press the [MENU] Button. SET EXIT USAGE TO MOVE JOYSTICK IN DIRECTION OF DESIRED FUNCTION 1/4 NEXTEXIT Notes:• When the Help Mode is used, functions cannot be set. • The Help Mode only displays the information available in [AUTO] Mode.• An explanation of the selected icon is displayed on the screen. • Each time the Joystick Control is moved down, the indication changes. „ Tape Playback Mode –▲ Playback / Pause p. 45 ► Fast (Cue Playback) p. 46 ◄ Rewind (Review Playback) p. 46 ▼ Stop p. 45 „ Picture Playback Mode (For PV-GS39/PV-GS59) –▲ Start the Slide Show Stop the Slide Showpp. 47~48 ► Playback the next picture p. 47 ◄ Playback the previous picturep. 47 ▼ Erase the picture p. 49 „ Card Recording Mode (For PV-GS39/PV-GS59) • When the [AUTO/MANUAL/FOCUS] Switch is set to [FOCUS]. 1/4 NEXT2/4 NEXT3/4 NEXTIRISSHTRWB 4/4 NEXT MF –MF + 4/4◄ Manual Focus Adjustment Modep. 44 ► Manual Focus Adjustment Modep. 44 ▼Go to next page. – Using the Menu Screen To facilitate the selection of a desired function or setup, this Camcorder displays various function setups on Menus. 1 Press the [MENU] Button. • The Menu corresponding to the Mode selected by the Mode Dial is displayed. • Do not switch the Mode Dial when the Menu is displayed. 2 Move the Joystick Control [▲] or [▼] to select the top menu. BASIC ADVANCED SETUP LANGUAGE SETUP ENTER EXIT (PV-GS39/ PV-GS59)(PV-GS29)
26 1 Press the [MENU] Button. 2 Select a menu item.• Use the Select Button (▲▼◄►) and [ENTER] Button in place of the Joystick Control on the main unit. 3 Press the [MENU] Button to exit the menu screen. Operating with Remote Control (PV-GS59 Only : Optional) The menu screen transition is the same as when the buttons on the main unit are used. [ BASIC]Basic Setup Sub-Menu [ SCENE MODE]Scene Mode (p. 40)[ REC SPEED]Recording Speed Mode (p. 29)[ WIND CUT]Wind Noise Reduction (p. 39)[ ASPECT] (For PV-GS39/PV-GS59)Wide Screen Mode (p. 39)[ CINEMA] (For PV-GS29)Cinema-like Format Recording (p. 39)[ CLOCK SET]Date and Time Setting (p. 21) List of Menus The figures of the Menus are for explanation purposes only, and they are different from the actual Menus. „ [TAPE RECORDING MENU] BASIC ADVANCED SETUP LANGUAGE SETUP ENTER EXIT BASICSCENE MODE REC SPEED WIND CUT ASPECT CLOCK SETOFF SP ON 16:9 NO SETUP ENTER EXITe.g., Selecting Language You can select the desired language. 1 Set [ LANGUAGE] >> [English], [Français] or [Español]. LANGUAGEEnglish EspañolFrançais SETUP ENTER EXIT 3 Move the Joystick Control [►] or press it to set the selection. 4 Move the Joystick Control [▲] or [▼] to select the Sub-Menu. BASICSCENE MODE REC SPEED WIND CUT ASPECT CLOCK SETOFF SP ON 16:9 NO SETUP ENTER EXIT 5 Move the Joystick Control [►] or press it to set the selection. 6 Move the Joystick Control [▲] or [▼] to select the item to be set. • While a Menu is displayed, you cannot record or play back. Menus can be displayed during playback but not during recording. BASICSCENE MODE REC SPEED WIND CUT ASPECT CLOCK SET SETUP ENTER EXITOFF 7 Press the Joystick Control to determine the setting. „ To Return to the Previous ScreenMove the Joystick Control [◄]. „ To Exit the Menu ScreenPress the [MENU] Button again. „ About the Menu Mode SettingThe setting selected on the Menu will be retained even when the Camcorder is turned off. However, if the Battery or AC Adaptor is disconnected before turning off the Camcorder, the selected setup may not be retained. • Menu operation flow is shown in this text by >>.
27 Before Using „ [TAPE PLAYBACK MENU] BASIC ADVANCED SETUP LANGUAGE SETUP ENTER EXIT BASICDATE/TIME USB FUNCTIOND/TMOTION DV SETUP ENTER EXIT e.g., [ BASIC]Basic Setup Sub-Menu [ DATE/TIME]Date and Time Indication (pp. 28, 70)[ USB FUNCTION] (PV-GS59 Only)USB Functions Mode (pp. 61, 67) [ ADVANCED]Advance Setup Sub-Menu [ PICT.QUALITY] (For PV-GS39/PV-GS59)Picture Quality (p. 32)[ EIS]Image Stabilizer (p. 36)[ FADE COLOR]Fade color (p. 37)[ AUDIO REC]Audio Recording Mode (p. 28)[ USB FUNCTION] (PV-GS59 Only)USB Functions Mode (pp. 61, 67)[ D.ZOOM]Digital Zoom (p. 36)[ ZOOM MIC]Zoom Microphone (p. 35)[ SHTR EFFECT] (PV-GS29 Only)Shutter effect (p. 31) [ SETUP]Setup Sub-Menu [ DISPLAY]Display Mode (p. 28)[ DATE/TIME]Date and Time Indication (pp. 28, 70)[ POWER SAVE]Power Save Mode (p. 29)[ QUICK START]Quick Start Mode (p. 34)[ REMOTE] (PV-GS59 Only)Remote Control Mode (p. 15)[ BEEP SOUND]Beep Sound (p. 28)[ LCD SET]LCD Adjustment (p. 22)[ EVF SET]Viewfinder Adjustment (p. 22)[ INITIAL SET]Initial Setting Mode (p. 29)[ DEMO MODE]Demonstration Mode (p. 29) [ LANGUAGE]Language Setup Sub-menu (p. 26) [ ADVANCED]Advance Setup Sub-Menu [ REC SPEED]Recording Speed Mode (p. 29)[ REC STDBY]Recording Standby Mode (p. 54)[ PICT.QUALITY] (For PV-GS39/PV-GS59)Picture Quality (p. 32)[ REPEAT PLAY]Repeat Play Mode (p. 45) [ SETUP]Setup Sub-Menu [ 12bit AUDIO]Audio Selector (p. 45)[ AUDIO OUT]Audio Output Mode (p. 29)[ DISPLAY]Display Mode (p. 28)[ REMOTE] (PV-GS59 Only)Remote Control Mode (p. 15)[ LCD SET]LCD Adjustment (p. 22)[ EVF SET]Viewfinder Adjustment (p. 22)[ POWER SAVE]Power Save Mode (p. 29)[ TV ASPECT] (For PV-GS39/PV-GS59)TV Aspect Mode (p. 51) [ LANGUAGE]Language Setup Sub-menu (p. 26) „ [CARD RECORDING MENU] (For PV-GS39/PV-GS59) BASIC ADVANCED SETUP LANGUAGE SETUP ENTER EXIT BASICSCENE MODE PICT.QUALITY ASPECT CLOCK SETOFF 16:9 NO SETUP ENTER EXITe.g., [ BASIC]Basic Setup Sub-Menu [ SCENE MODE]Scene Mode (p. 40)[ PICT.QUALITY]Picture Quality (p. 32)[ ASPECT]Wide Screen Mode (p. 39)[ CLOCK SET]Date and Time Setting (p. 21) [ ADVANCED]Advance Setup Sub-Menu [ BURST MODE]RapidFire Consecutive Photoshot (p. 33)[ SHTR EFFECT]Shutter Effect (p. 32)
28 Menus Related to Taking Pictures „ DATE/TIME This switches between date and time indications. Set [ BASIC] or [ SETUP] >> [ DATE/TIME] >> [D/T], [DATE] or [OFF]. • The Camcorder automatically records the date and time of picture taking on the tape. • You can also show or change the Date/Time Indication by repeatedly pressing the [DATE/ TIME] Button on the Remote Control (PV-GS59 Only). „ DISPLAYSet [ SETUP] >> [ DISPLAY] >> [ON] or [OFF]. Set to [ON] and the display mode can be switched to all functions. Set to [OFF] and it can be switched to minimum display. „ AUDIO REC• Set to Tape Recording Mode. You can select the sound quality of the recorded sound. Set [ ADVANCED] >> [ AUDIO REC] >> [12bit] or [16bit]. [12bit]: Records audio in “12 bit 32 kHz 4 tracks”. (The original audio signals can be kept after the other audio signals are dubbed.) [16bit]: Records audio in “16 bit 48 kHz 2 tracks”. Audio can be recorded in higher quality. (If audio signals are dubbed, then the original audio signals will be erased.) „ BEEP SOUND• Set to Tape/Card Recording Mode. When [ BEEP SOUND] on the [ SETUP] is set to [ON], confirmation/alarm beeps are issued as follows. 1 Beep • When you start recording • When you turn on the power • When the unit goes from Quick Start standby mode to recording pause 2 Beeps • When you pause recording • When you turn off the power • When the unit goes into Quick Start standby mode 2 Beeps 4 times • When a cassette with its erasure prevention tab set to [SAVE] is inserted, condensation occurs (p. 73), and at other times. Check the sentence displayed on the screen (p. 71). [ SETUP]Setup Sub-Menu [ DISPLAY]Display Mode (p. 28)[ DATE/TIME]Date and Time Indication (pp. 28, 70)[ POWER SAVE]Power Save Mode (p. 29)[ QUICK START]Quick Start Mode (p. 34)[ REMOTE] (PV-GS59 Only)Remote Control Mode (p. 15)[ BEEP SOUND]Beep Sound (p. 28)[ LCD SET]LCD Adjustment (p. 22)[ EVF SET]Viewfinder Adjustment (p. 22)[ INITIAL SET]Initial Setting Mode (p. 29) [ LANGUAGE]Language Setup Sub-menu (p. 26) [ BASIC]Basic Setup Sub-Menu [ DATE/TIME]Date and Time Indication (pp. 28, 70)[ PROTECT]Setting the Lock (p. 50) [ ADVANCED]Advance Setup Sub-Menu [ DPOF SET]Setting DPOF (p. 50)[ FORMAT CARD]Formatting a Card (p. 51) [ SETUP]Setup Sub-Menu [ DISPLAY]Display Mode (p. 28)[ REMOTE] (PV-GS59 Only)Remote Control Mode (p. 15)[ LCD SET]LCD Adjustment (p. 22)[ EVF SET]Viewfinder Adjustment (p. 22)[ POWER SAVE]Power Save Mode (p. 29)[ TV ASPECT]TV Aspect Mode (p. 51) [ LANGUAGE]Language Setup Sub-menu (p. 26) „ [PICTURE PLAYBACK MENU] (For PV-GS39/PV-GS59) BASIC ADVANCED SETUP LANGUAGE SETUP ENTER EXIT BASICDATE/TIME PROTECTD/T NO SETUP ENTER EXITe.g.,
29 Before Using „ POWER SAVESet [ SETUP] >> [ POWER SAVE] >> [5 MINUTES] or [OFF]. [OFF]: When about 5 minutes passed without any operation, the standby mode automatically will be set. In the standby mode, [ ] blinks and it takes time more than usual to start recording after you press the Recording Start/Stop Button. [5 MINUTES]: When about 5 minutes passed without any operation, the Camcorder automatically turns off to protect the tape or to prevent the battery from running down. When you use the Camcorder, turn it on again. • In the following cases, the power may not turn off even when set [ POWER SAVE] >> [5 MINUTES]. - When connecting to the AC Jack (When using the AC Adaptor) - When connecting the USB Cable or the DV Cable to a PC or other equipment - When the PC Mode (For PV-GS39/PV-GS59) Menus Related to Playback „ AUDIO OUT This switches the sound to be played back. Set [ SETUP] >> [ AUDIO OUT] >> [STEREO], [L] or [R]. [STEREO]: Stereo sound (main sound and sub sound) [L]: Left channel sound (main sound) [R]: Right channel sound (sub sound) Other Menus „ INITIAL SET • Set to Tape/Card Recording Mode. Set [ SETUP] >> [ INITIAL SET] >> [YES] or [NO]. Set to [YES] to change menu settings back to their factory default condition. • The initializing takes a little while. • Language setting cannot be back to the initial shipping condition. „ DEMO MODE• Set to Tape Recording Mode. If you set [ SETUP] >> [ DEMO MODE] >> [ON] without inserting a cassette or a card, the Camcorder is automatically set to the demonstration mode for introducing its functions. If any button is pressed or operated, the demonstration mode is canceled. If no operations take place for approx. 10 minutes, the demonstration mode automatically starts. To terminate the demonstration mode, insert a cassette or a card, or set to [ DEMO MODE] >> [OFF]. For normal use, set this function to [OFF]. LP Mode You can switch the tape recording speed.• Set to Tape Recording/Playback Mode. 1 Set [ BASIC] or [ ADVANCED] >> [ REC SPEED] >> [LP]. If the LP mode is selected, the recording time will be 1.5 times the SP mode, but some functions will be disabled. • We recommend using the SP mode for important recordings. • In order to fully exhibit the performances of the LP mode, we recommend using Panasonic cassettes marked LP mode. • Audio dubbing is not possible with LP Mode. (p. 53) • In the LP mode, the picture quality will not be degraded in comparison with the SP mode, but mosaic noise may appear on the playback image or some functions may be disabled. - Playback on other digital video equipment or on digital video equipment without the LP mode. - Playback of the image on other digital video equipment recorded in the LP mode. - Slow Motion/Still Advance playback.
30 About Recording • When recording pictures on a tape, set the Mode Dial to Tape Recording Mode [ ]. • When recording still pictures on a card, set the Mode Dial to Card Recording Mode [ ] (For PV-GS39/PV-GS59). • When recording with the [AUTO/MANUAL/FOCUS] Switch set to [AUTO], the Camcorder automatically adjusts the Focus and White Balance. In some cases, they cannot be adjusted automatically and need to be adjusted manually. (pp. 41, 44) • Before turning on the power, remove the Lens Cap. If the Lens Cap is still attached when the power is turned on, Automatic White Balance Adjustment (p. 41) may not function correctly. Recording on a Tape 1 Set the [OFF/ON] Switch to [ON].• The [STATUS] Indicator lights Red. 2 Set the Mode Dial to Tape Recording Mode. • The [ TAPE RECORDING MODE] is displayed on the screen. 4 Press the Recording Start/Stop Button again to pause the recording. • The [PAUSE] and [ ] Indication appears. 3 Press the Recording Start/Stop Button.• Recording starts. • The [RECORD] and [●] Indication appears. Recording Mode SP 3h59m59s29f R 2:00 12:34:56AM JAN 2 2006 100 * These indications are displayed only when the card is inserted. (For PV-GS39/PV-GS59) 1) Recording mode 2) Recording time elapse 3) Remaining tape indication 4) Still picture size 5) Quality of still pictures 6) Number of recordable still pictures (When no picture can be recorded, this indication will flash in red.) „ On-screen Display in the Tape Recording Mode 1) 3) 4)* 5)* 6)*2) • For the recording time on a tape, refer to page 16. • Carry out a recording check (p. 31) to verify that the image is recorded properly. • In order to find the unrecorded section, carry out the blank search (p. 31). „ Concerning the remaining tape time indication on the screen • The remaining tape time is indicated in minutes. (When it reaches less than 3 minutes, the indication starts flashing.) • During a 15-second or shorter recording, the remaining tape time indication may not be displayed or the remaining tape time may not be displayed correctly. • In some cases, the remaining tape time indication may display remaining tape time that is 2 to 3 minutes shorter than the actual remaining tape time. (PV-GS39/ PV-GS59)(PV-GS29) SP 3h59m59s29f R 2:00 12:34:56AM JAN 2 2006 100 RECORD SP 3h59m59s29f R 2:00 12:34:56AM JAN 2 2006 100 PAUSE • Open the LCD Monitor or extend the Viewfinder before turning on the power. • When this unit is purchased, the aspect ratio is set to [16:9] for recording images compatible with a wide-screen TV. To make this unit compatible with regular TVs (4:3), change the [ ASPECT] setting before recording the images (p. 39) or change the [ TV ASPECT] setting when watching them on the connected TV (p. 51).