Panasonic Pv Gs250 Operating Instructions Manual

							Before using
21LSQT0862
2) Tape recording mode
([AUTO/MANUAL/FOCUS] switch is set to 
[MANUAL]) 
3) Tape playback mode
4) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to 
[AUTO]) 5) Card recording mode
([AUTO/MANUAL/FOCUS] switch is set to 
[MANUAL]) 
6) Picture playback mode
Switching the language
You can switch the language on the screen 
display or the menu screen.
1Set [LANGUAGE] >> [English].  4  White balance
Shutter speed
Iris or gain value 
-38-
 1  Select/Adjust -38-
 2  Select/Adjust -38-
 3  Playback/pause -41-
 4  Stop -41-
 2   Rewind (review playback) -41-
 1   Fast forward (cue playback)  -41-
 3  Tele-macro -34-
 4   Soft skin mode -33-
 1  Backlight compensation -33-
Screen display
OFF
Screen
display OFF
Screen
display OFF
 4   White balance
 Shutter speed
 Iris or gain value -38-
 1  Select/Adjust -38-
 2  Select/Adjust -38-
 3  Playback/stop -43-
 4  Erase -44-
 2   Playback previous picture -43-
 1   Playback next picture  -43-
Screen
display OFF
Screen
display OFF
LSQT0862ENG.book  21 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Before using
22LSQT0862
Using the menu screen
For each individual menu, please refer to -62-.1Press the [MENU] button.
≥The menu corresponding to the mode 
selected by the mode dial is displayed.
≥Do not switch the mode dial when the menu is 
displayed.
2Move the joystick up or down in order to 
select the top menu.
3Move the joystick right or press it to set the 
selection.
4Move the joystick up or down in order to 
select the sub-menu.
5Move the joystick right or press it to set the 
selection.
6Move the joystick up or down in order to 
select the item to be set.
7Press the joystick to determine the setting.
ª
To exit the menu screen Press the [MENU] button.
ª
To get back to the previous screenMove the joystick left.
ª
About the menu setting≥The menu screen does not appear during 
recording. And you cannot record when the 
menu screen appears.
ª
Operating with remote controlThe menu screen transition is the same as when 
the buttons on the main unit are used.
1Press the [MENU] button.
2Select a menu item.
≥Use the direction buttons (π,∑,∏,∫) and 
[ENTER] button in place of the joystick on the 
main unit.
3Press the [MENU] button, to exit the menu 
screen.
MENU
ENTER
VA R .
SEARCHMENU
ENTER
VA R .
SEARCHMENU
ENTER
VA R .
SEARCHMENU
LSQT0862ENG.book  22 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Before using
23LSQT0862
Setting date and time
If the screen shows the incorrect date/time, then 
adjust it.
≥Set to Tape Recording Mode or Card 
Recording Mode.
1Set [BASIC] >> [CLOCK SET] >> [YES].
2Move the joystick left or right in order to 
select the item to be set. Then move the 
joystick up or down to set the desired value.
≥The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
≥The 12-hour clock is used.
3Press the joystick to determine the setting.
≥The clock function starts at [00] seconds.
ª
About date/time≥The date and time function are driven by a 
built-in lithium battery.
≥Make sure to check the time before recording 
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery≥If [0] or [--] is indicated when the Camcorder is 
turned on, then the built-in lithium battery has 
run down. Connect the AC adaptor to the 
Camcorder or place the battery on the 
Camcorder, and the built-in lithium battery will 
be recharged. Leave the Camcorder as is for 
approx. 24 hours, and the battery will drive the 
date and time for approx. 6 months. (Even if the 
[OFF/ON] switch is set to [OFF], the battery is 
still being recharged.)
Adjusting LCD monitor/viewfinder
ªAdjusting the brightness and color 
level
1
Set [SETUP] >> [LCD SET] or [EVF SET] >> 
[YES].
2Move the joystick up or down in order to 
select the item to be adjusted.
[LCD SET]
: Brightness of the LCD monitor
: Color level of the LCD monitor
[EVF SET]
: Brightness of the viewfinder
3Move the joystick left or right to move the 
bar indication representing the brightness.
4Press the [MENU] button or the joystick to 
complete the settings.
≥In order to adjust the brightness of the 
viewfinder, close the LCD monitor, and the 
viewfinder will be activated.
≥When the LCD monitor is rotated by 180° 
towards the lens, the brightness of the LCD 
monitor cannot be adjusted.
≥These settings will not affect the images actually 
recorded.
EVF
LSQT0862ENG.book  23 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Before using
24LSQT0862
ªIn order to increase the brightness of 
the entire LCD monitor
1
Press the [POWER LCD] button.
≥The [POWER LCD] lamp lights up.
≥If the [POWER LCD] button is pressed, the 
entire LCD monitor will become approx. twice 
as bright as the normal.
≥Press this button again, and the lamp will go off 
and the brightness will revert back to the original 
brightness.
≥This will not affect the images to be recorded.
≥If you turn on the Camcorder when the AC 
adaptor is used, the [POWER LCD] function will 
automatically be activated.
ª
Changing the picture quality on the 
LCD monitor
1
Set [SETUP] >> [LCD AI] >> [DYNAMIC] or 
[NORMAL].
[DYNAMIC]: The image on the LCD monitor 
becomes clear and vivid. Optimum 
contrast and brightness are set 
depending on the scenes recorded. 
Clear and brilliant images are 
presented. (The effect will vary 
depending on the images 
recorded.)
[NORMAL]: Switches to the standard picture 
quality.
≥The effect will vary depending on the scene 
recorded.
≥The picture quality on the viewfinder will not be 
affected.
≥This function is automatically set to [DYNAMIC] 
when the brightness of the LCD monitor is 
increased (when the [POWER LCD] lamp lights 
up) and cannot be set to [NORMAL] 
independently.
≥This will not affect the images to be recorded.
≥When the LCD monitor is rotated by 180° 
towards the lens, the picture quality of the LCD 
monitor is temporarily adjusted as if the 
[LCD AI] is set to [NORMAL].
Using the remote control
ªRemote controlUsing the remote control supplied will enable 
control of almost all functions of this Camcorder.
(1)Date/time button [DATE/TIME] -62-
(2)On-screen display button [OSD] -43-
(3)Record button [¥REC] -47-,-48-
(4)Audio dubbing button [A.DUB] -49-
(5)Direction buttons [π,∑,∏,∫] -22-
(6)
Slow/frame-by-frame forward button 
[E,D] (E: reverse, D: forward) -42-
(7)Zoom/volume button [ZOOM/VOL] ¢(8)Search button [VAR. SEARCH] -42-
(9)Menu button [MENU] -22-
(10)
Photoshot button [PHOTO SHOT] ¢(11)Rewind/review button [6] (12)Pause button [;] (13)Stop button [∫] 
POWER LCD
STOP OSD
V/REWSTILL ADV
DATE/
TIME
VOL
ZOOM¥RECPHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER
VA R .
SEARCHMENU
T
W
(1)
(2)
(3)
(4)
(5)
STOP OSD
V/REWSTILL ADV
DATE/
TIME
VOL
ZOOM¥RECPHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
VA R .
SEARCHMENUENTER
T
W
(6)(7)
(8)
(9)
STOP OSD
V/REWSTILL ADV
DATE/
TIME
VOL
ZOOM¥RECPHOTO
SHOT
START/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
VA R .
SEARCHMENUENTER
T
W
(10)
(14)
(17) (15)
(16)
(11)
(12)
(13)
LSQT0862ENG.book  24 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Before using
25LSQT0862
(14)Recording start/stop button [START/
STOP] ¢
(15)Playback button [1] (16)Fast forward/cue button [5](17)Enter button [ENTER] -22-¢ means that these buttons function in the same 
manner as the corresponding buttons on the 
Camcorder.
ª
Install a button-type batteryInstall the button-type battery supplied in the 
remote control before using it.
1While pressing the stopper 1, pull out the 
battery holder.
2Set the button-type battery with its (i) mark 
facing upward and slide the battery holder 
back into place.ª
Remote control usable range
≥The distance between the remote control and 
the Camcorder: Within approx. 15 feet (5 m)
Angle: Approx. 10o up and 15o down, left, and 
right
ª
Selecting the remote control modeIf 2 Camcorders are used simultaneously, set the 
mode for one pair of Camcorder and remote 
control to [VCR1] and that of the other pair to 
[VCR2]. This will prevent interference between 
the 2 pairs. (The default setting is [VCR1]. When 
the button-type battery is replaced, the setting will 
revert to the default [VCR1].) 
1Setting on the Camcorder:
Set [SETUP] >> [REMOTE] >> [VCR1] or 
[VCR2].
2Setting on the remote control:
[VCR1]:
Press [D] and [∫] simultaneously. 1
[VCR2]:
Press [E] and [∫] simultaneously. 2
ª
Concerning the button-type battery≥When the button-type battery runs down, replace 
it with a new battery (part number: CR2025). The 
battery is normally expected to last about 1 year, 
but it depends on operation frequency.
≥Keep the button-type battery out of the reach of 
children.
≥If the remote control mode of the Camcorder 
and that of the remote control do not match with 
each other, “REMOTE” will appear. When the 
remote control is operated for the first time after 
the Camcorder is turned on, “CHECK REMOTE 
MODE” (
-67-) will appear and operation is 
impossible. Set the same remote control mode.
≥The remote control is intended for indoor 
operation. Outdoors or under strong light, the 
Camcorder may not operate properly even 
within the usable ranges.
≥Within a 3 feet (1 m) range, you can operate the 
remote control using the remote control sensor 
on the LCD monitor side of the Camcorder. Warning
Danger of explosion if battery is 
incorrectly replaced.
Replace only with the same or equivalent 
type recommended by the equipment 
manufacturer. Discard used batteries 
according to manufacturer’s instructions.
Risk of fire, explosion and burns. Do not 
recharge, disassemble, heat above 212°F 
(100°C) or incinerate. Keep the Button-
Type battery out of the reach of children. 
Never put Button-Type battery in mouth. 
If swallowed, call your doctor.
Replace battery with Panasonic PART NO. 
CR2025 only. Use of another battery may 
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep 
away from children. 
Do not recharge, disassemble or dispose of 
in fire.
1
STOP
STILL ADVVOLPAUSESTILL ADV
VA R
21
LSQT0862ENG.book  25 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Before using
26LSQT0862
Magic Wire Remote Control with 
Narration Mic
This controller can be used from different high 
and low angles. It is also handy when a tripod is 
used. When you do not use the controller, attach 
the clip to the grip belt. Left-handed users can use 
this Camcorder more easily.
(1)Microphone [MIC](2)Recording start/stop button [REC](3)Zoom lever [W/T](4)Photoshot button [PHOTO SHOT](5)Microphone switch button [TALK]
ª
Connect the Magic Wire Remote 
Control with Narration Mic to the 
Camcorder
1
Plug the Magic Wire Remote Control with 
Narration Mic into the [REMOTE] terminal 
as far as it goes.ª
Switching the microphonePress the [TALK] button on the Magic Wire 
Remote Control with Narration Mic, and the 
microphone on the remote control will be 
activated instead of that on the Camcorder.
≥While this button is being pressed, [ ] appears 
and the microphone on the remote control is 
activated.
≥We recommend you talk with the microphone 
approx. 4 inches (10 cm) away from your 
mouth.
ª
About the clip (on the backside)
When you move with the clip fitted to your pocket 
or elsewhere, beware of knocking over the tripod 
or causing the Camcorder to fall off the table.
≥The [PHOTO SHOT] button on the Magic Wire 
Remote Control with Narration Mic cannot be 
pressed halfway.
≥If the pin plug of the control is not inserted 
securely into the [REMOTE] terminal as far as it 
will go, normal operation may not be ensured.
≥Before using, make sure that the plug is 
inserted securely into the terminal as far as it 
will go.
(1)
(2)
(3)
(4)
(5)
REMOTE/MIC
LSQT0862ENG.book  26 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Record mode
27LSQT0862
Record mode
Check before recording
Check the following by a trial recording before 
important events such as weddings in order to 
verify that the image recording and audio 
recording work properly and that you know how to 
use the Camcorder.
ª
Basic Camcorder holding
1) Hold the Camcorder with both hands.
2) Run your hand through the grip belt.
3) Do not cover the microphones or sensors with 
your hands.
4) Keep your arms near your body.
5) Slightly open your legs.
≥When you are in the open air, record pictures 
with the sunlight as far in the background as 
possible. If the subject is backlit, it will become 
dark in the recording.
ª
Check points≥Remove the lens cap. (-14-)
(When the Camcorder is turned on with the lens 
cap fitted, the automatic white balance 
adjustment may not function properly. Please 
turn the Camcorder on after removing the lens 
cap.)
≥Grip belt adjustment (
-15-) 
≥Power supply (-16-) 
≥Insert a cassette/card. (-18-,-19-)
≥Setting date/time (-23-) 
≥Adjustment of LCD monitor/viewfinder (-23-) 
≥Getting the remote control ready (-24-) 
≥Setting SP/LP mode (-27-)ª
About auto mode≥Set the [AUTO/MANUAL/FOCUS] switch to 
[AUTO], and color balance (white balance) and 
focusing will be adjusted automatically.
≥Auto white balance: 
-78-≥Auto focusing: -78-≥Color balance and focus may not be adjusted 
depending on light sources or scenes. If so, 
manually adjust the white balance and focus.
≥Scene mode setting (
-37-) 
≥White balance setting (-38-) 
≥Shutter speed setting (-40-) 
≥Iris/gain value setting (-40-) 
≥Focus setting (-39-) 
ª
Recording modeYou can switch the tape recording mode.
≥Set to Tape Recording/Playback Mode.
1Set [BASIC] or [ADVANCE] >> [REC SPEED] 
>> [SP] or [LP].
If the LP mode is selected, the recording time will 
be 1.5 times the SP mode, but some functions will 
be disabled.
≥We recommend using the SP mode for 
important recording.
≥In order to fully exhibit the performances of the 
LP mode, we recommend using Panasonic 
cassettes marked LP mode.
≥It is not possible to dub audio onto images 
recorded in the LP mode. (
-49-) 
≥In the LP mode, the picture quality will not be 
degraded in comparison with the SP mode, but 
mosaic noise may appear on the playback 
image or some functions may be disabled.
≥Playback on other digital video equipment 
or on digital video equipment without the LP 
mode
≥Playback of the image on other digital video 
equipment recorded in the LP mode
≥Slow/frame-by-frame playback
1)
4)
5) 2)
3)AUTO
MANUAL
FOCUS
LSQT0862ENG.book  27 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Record mode
28LSQT0862
Recording on a tape
≥Remove the lens cap. (-14-)
(When the Camcorder is turned on with the lens 
cap fitted, the automatic white balance 
adjustment may not function properly. Please 
turn the Camcorder on after removing the lens 
cap.)
≥Set to Tape Recording Mode.
1Press the recording start/stop button to 
start recording.
2Press the recording start/stop button again 
to pause recording.
≥For details on the recording time on a tape, refer 
to 
-17-.
≥Carry out a recording check (-29-) to verify that 
the image is recorded properly.
≥In order to find the unrecorded section, carry out 
the blank search (
-29-).ª
On-screen display in the tape 
recording mode
¢These indications are displayed only when the 
card is inserted.
1) Recording time elapsed
2) Remaining tape indication
3) Still picture size
4) Number of recordable still pictures
(When no picture can be recorded, this 
indication will flash in red.) 
5) Quality of still pictures
ª
Concerning the remaining tape time 
indication on the screen
≥The remaining tape time is indicated in minutes. 
(When it reaches less than 3 minutes, the 
indication starts flashing.) 
≥During a 15-second or shorter recording, the 
remaining tape time indication may not be 
displayed or the remaining tape time may not be 
displayed correctly.
≥In some cases, the remaining tape time 
indication may display remaining tape time that 
is 2 to 3 minutes shorter than the actual 
remaining tape time.
ª
[POWER SAVE][OFF]: When 5 minutes passes without 
any operation, the standby mode 
will be automatically set. In the 
standby mode, [;] blinks and it 
takes more time than usual to start 
recording after you press the 
recording start/stop button.
[5 MINUTES]: When 5 minutes passes without 
any operation, the Camcorder 
automatically turns off to protect 
the tape or to prevent the battery 
from running down. When you 
want to use the Camcorder, turn it 
on again.
≥The Camcorder cannot be automatically turned 
off when you connect the USB connection cable 
or the DV cable with the Camcorder or when the 
Camcorder is in the PC mode.
PCPC
;

ç÷

ú÷÷
/÷÷
4ø÷
:÷÷
-
ø÷÷
1)
2)
3)¢
4)¢
5)¢
LSQT0862ENG.book  28 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Record mode
29LSQT0862
Recording still pictures on a card 
while recording image onto a tape
You can record still pictures while recording 
image onto a tape.
≥Set to Tape Recording Mode.
1Press the [PHOTO SHOT] button fully while 
recording image onto a tape.
≥For the number of still pictures to be recorded 
on a card, refer to -80-.
≥When recording pictures onto a card, the 
recording start/stop button is disabled.
≥You can select a picture quality for still pictures 
to be recorded. (
-31-) 
≥In tape recording mode, the size of pictures that 
can be recorded is [640].
≥In order to record higher quality still pictures, 
you must use the card recording mode.
≥If the wide mode is used, you cannot record 
images onto the card.
≥The [PHOTO SHOT] button does not work if it is 
pressed halfway.
Check the recording
The last image recorded is played back for 2 to 
3 seconds. After checking, the Camcorder will be 
set to a recording pause.
≥Set to Tape Recording Mode.
1Press the joystick during the recording 
pause until the icon 1 appears.
2Move the joystick down to select the 
recording check icon [ ].
Blank search function
Searches for the last part of the image recorded 
(unused part of the tape).
≥Set to Tape Recording/Playback Mode.
1Set [BASIC] or [ADVANCE] >> 
[BLANK SEARCH] >> [YES].
ª
Stopping a blank search midway 
through
Move the joystick down.
≥If the cassette tape has no blank part, then the 
Camcorder will stop at the end of the tape.
≥The Camcorder stops at a point approx. 
1 second before the end of the last image 
recorded. When you start recording at that 
point, the image can be recorded seamlessly 
from the last image.
PHOTO
SHOT
1
LSQT0862ENG.book  29 ページ  ２００４年１２月２１日　火曜日　午後５時９分 
						

							Record mode
30LSQT0862
Recording still pictures onto a card 
(Photoshot) 
≥Set to Card Recording Mode.
1Press the [PHOTO SHOT] button halfway in 
order to adjust focusing. (For auto focusing 
only) 
≥If you set [EIS] to [ON], then the image 
stabilizer function will be more effective. 
(MEGA Optical image stabilizer will be 
indicated.) 
≥The iris/gain value is fixed and this 
Camcorder focuses on the subject 
automatically.
1Shutter chance mark
± (The white lamp flashes.):
Focusing
¥ (The green lamp lights up.):
When in focus
No mark: When focusing is unsuccessful
≥The shutter chance mark is indicated as follows 
when the [PHOTO SHOT] button is not pressed 
halfway. Please use it as a guide for recording.
¥ (The green lamp lights up.):
When in focus and a good picture 
can be recorded
± (White lamp lights up.):
Almost in focus
2Focus area
2Press the [PHOTO SHOT] button fully.
ª
To record still pictures clearly≥When zooming in on the subject with a 
magnification of 4k to 10k or higher, it is 
difficult to reduce the slight shaking from holding 
the Camcorder by hand. We recommend 
decreasing the zoom magnification and 
approaching the subject when recording.
≥When recording still pictures, hold the 
Camcorder firmly with your hands and keep your arms stationary at your side so as not to 
shake the Camcorder.
≥You can record stable pictures without shaking 
by using a tripod and the remote control.
≥For the number of still pictures to be recorded 
on a card, refer to -80-.
≥The sound cannot be recorded.
≥While data is being recorded on a card, do not 
operate the mode dial.
≥When the access lamp is lit, do not insert or 
remove a card.
≥Another product may degrade or not play back 
data recorded on this Camcorder.
≥If set [PICT. QUALITY] >> [ ], mosaic-pattern 
noise may appear on a playback image 
depending on the picture content.
≥When the [PICTURE SIZE] is set to other than 
[640], the mega pixel recording mode is set.
≥When the picture size setting is other than [640], 
the scene around the subject can be recorded 
wider than that in [640].
ª
On-screen display in the card 
recording mode
1) Still picture size
2) Number of recordable still pictures
(When no pictures can be recorded, the red 
light will flash.) 
3) Quality of still pictures
ª
Progressive PhotoshotYou can record still pictures with higher picture 
quality and frames. (You cannot switch the 
progressive function off/on.) 
≥In the tape recording mode, the progressive 
function may be disabled depending on the 
other functions used. (
-69-) 
PC
PHOTO
SHOT
1
2
ø÷÷
1)
2)
3)
LSQT0862ENG.book  30 ページ  ２００４年１２月２１日　火曜日　午後５時９分