Panasonic Projector Pt Lb20vu Operating Instructions

ENGLISH-21
Getting started
Connections
Notes on connections
BRead the instruction manual for each peripheral device carefully before connecting it.
BTurn off the power supply for all peripheral devices before making any connections.
BIf the cables necessary for connection are not included with the peripheral device or
available as an option, you may need to prepare a proper cable for the device concerned.
BIf there is a lot of jitter in the video signal, the projected image may flicker. In such cases,
it...

22-ENGLISH
NOTE:
BIf the signal cables are disconnected or if the power supply for the
computer or video deck is turned off while “D.ZOOM”(digital zoom) or
“INDEX WINDOW” is being used, these functions will be cancelled.
Connecting to video equipment
D-sub15-pin (male) - BNCx5 (male) adapter cable
DVD player
(with component
video connectors)
DIN 8-pin
(male)
DVD player Video deckComputer for control use
Red (connect to PRsignal connector)
Blue (connect to P
Bsignal connector)
Green (connect to Y signal...

ENGLISH-23
Getting started
Insert the accessory lithium battery while making sure that the polarities are correct.
#While pushing the battery holder tab to the right, pull out the battery
holder.
$Insert the battery into the battery holder so that the + side is facing
upward.
%Insert the battery holder.
Preparation for the remote control unit
Push the tab
Pull out
Back side
Match the “+” surface of the battery
with the “+” marked side of the
battery holder.
NOTE:
BDo not drop the remote control unit....

ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
)
*
$
&
(
'
#
Turning on the power
Before turning on the power
1. Ensure that all peripheral
devices are connected
properly.
2. Remove the lens cover.
Lens coverPower cord
Connect the accessory power cord to the AC IN
socket.
BThe POWER button on the projector will illuminate red.
Press the POWER button.
BThe POWER button on the projector will flash green. After a short
period, it will illuminate green,...

ENGLISH-25
Basic operation
Press the input select button to select the
input signal.
Follow the procedure below when you set the projector up first, and when
you change the setup place.
Press the AUTO SETUP button to
initiate automatic positioning.
BThe tilt of the projector and the input
signal will be detected and keystone
distortion and the position of the image
will be corrected.
(Refer to page 28 for details.)
Adjusting the size
BTurn the zoom ring to adjust the size of the projected image....

FREEZESHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
ENTER
#
$
%
Turning off the power
POWER button
Press the POWER button.
B“POWER OFF” is displayed on the
screen.
Press the I I
or H H
button to select “OK”, and
then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected.
(The POWER button on the projector will illuminate orange while the
cooling fan is still operating.)
NOTE:
BYou can also turn off the power by pressing the...

ENGLISH-27
Basic operation
POWER button on the projector
POWER button status
RedIlluminatedThe projector is in standby mode and image projection
is possible by pressing the POWER button.
A picture is being projected.
The lamp is cooling down after the power has been
turned off or while direct power off function is
operating.
The projector is preparing for projection after the
power has been turned on while the POWER button
on the projector is illuminated orange. (After a short
period, a picture will be...

28-ENGLISH
Correcting keystone distortion and
automatic positioning (AUTO SETUP)
This projector detects its degree of tilt and the input signal. Keystone
distortion and the position of the image can then be corrected automatically
in accordance with the input signal.
ENTER
FREEZE
SHUTTER
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
Projector control panelPress the AUTO SETUP button.
(When the projected image has caused keystone distortion)
BAutomatic positioning
will be...

ENGLISH-29
Useful functions
Turning off the picture and sound
momentarily (SHUTTER)
The “SHUTTER” function can be used to momentarily turn off the picture and
sound from the projector when the projector is not being used for short
periods of time, such as during breaks in meetings or when carrying out
preparation. The projector uses less power in “SHUTTER” mode than it does
in normal projection mode.
ENTER
FREEZE
INDEX
WINDOW
PROJECTOR VOLUME D.ZOOMSTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
SHUTTER
ENTER...

30-ENGLISH
ENTER
INDEX
WINDOW
PROJECTOR VOLUMESTD VIDEOINPUT POWER
RGB
MENU
AUTO
SETUP
SHUTTERFREEZE
D.ZOOM
BThe picture will then
be enlarged to 1.5
times the normal size.
The remote control unit functions during D.ZOOM (digital zoom)
Press the D.ZOOM +/- buttons to change the enlargement ratio.
Press the F,G,IandHbuttons to move the enlarged area which you want to project.
Press the MENU button to return to the normal screen.
INDEX
WINDOW
PROJECTORSTD
D.ZOOMVOLUME
[
Enlarging the picture (D.ZOOM)...