Panasonic Projector PT-DZ10KU User Manual

Chapter 1 Preparation — Precautions for use
ENGLISH - 21
Optional accessories
Optional accessories (product name) Model No.
Projection lens Zoom lens
ET
-

D75LE6, ET
-
 D75LE8, ET
-
 D75LE10, ET
-
 D75LE20, 
ET
-

D75LE30, ET
-
 D75LE40
Fixed-focus lens ET
-

D75LE50
Ceiling Mount Bracket for 
Projectors ET
-

PKD310H (for High Ceilings), ET
-
 PKD310S (for Low Ceilings)
Projector ceiling mount 
bracket ET
-

PAD310
Projector Frame for 
projectors ET
-

PFD310
Replacement lamp unit ET
-

LAD310A (1...

Chapter 1 Preparation — Start-up display
22 - ENGLISH
Start-up display
When the projector is switched on for the first time after purchase as well as when [ALL USER DATA] in the [PROJECTOR SETUP] menu → 
[INITIALIZE] is executed, the focus adjustment screen is displayed after\
 projection starts, then the initial setting screen is displayed. Set th\
em 
in accordance with circumstances.
In other occasions, you can change the settings by menu operations.
Focus adjustment
Adjust the focus to display the...

Chapter 1 Preparation — Start-up display
ENGLISH - 23
Initial setting (installation setting)
Set [PROJECTION METHOD] and [COOLING CONDITION] depending on the installation mode. Refer to “Installation mode” (x   page   31) 
for details.
Set [HIGH ALTITUDE MODE] to [ON] when using the projector at high altitudes between 1
  400   m (4   593') or higher and lower than 2   700   m 
(8
  858') above sea level.
After completed the initial setting, you can change the settings of each\
 item from the...

Chapter 1 Preparation — About your projector
24 - ENGLISH
About your projector
Remote control
1
3 2
4
5
7 6
8
9
10 11
12
19
13
14
15
16
17
18 20
21
Front SideTo p
Bottom
1 Remote control indicator
Flashes if any button in the remote control is pressed.
2
 
Power standby <
 v> button
Sets the projector to the state where the projector is switched 
off (standby mode) when the  switch on the 
projector is set to  and in projection mode.
3
 
Power on < b

> button
Starts projection when the  switch on the...

Chapter 1 Preparation — About your projector
ENGLISH - 25
Note
 fThe remote control can be used within a distance of about 30   m (98'5") if pointed directly at the remote control signal receiver . The remote 
control can control at angles of up to ±15° vertically and ±30° horizontally , but the effective control range may be reduced.
 fIf there are any obstacles between the remote control and the remote control signal receiver , the remote control may not operate properly

.
 fThe signal will be...

Chapter 1 Preparation — About your projector
26 - ENGLISH
13 Security slot
This security slot is compatible with the Kensington security 
cables.
14
 
Air intake port
15

 
 terminal
Connect the supplied power cord. 16

  switch
T
urns on/off the main power.
17
 
Air filter cover
The air filter unit is inside.
18

 
Burglar hook port
Attaches a burglar prevention cable, etc.
Attention
 fDo not block the ventilation ports (intake and exhaust) of the projector .
 rControl panel
VIDEOENTER
MENULENS
SHUTTER...

Chapter 1 Preparation — About your projector
ENGLISH - 27
 rConnecting terminals
1 2 3 4
7 8 9 10 11 12 13
 5
66
1  terminal/ terminal
These are the terminals to connect the remote control for serial 
control when the system uses multiple projectors.
2
 
 terminal
This is a terminal to remotely control the projector using the 
external control circuit.
3

 
 terminal
This is the RS
- 232C compatible terminal to externally control 
the projector by connecting a computer.
4
 
 terminal
This is a terminal...

Chapter 1 Preparation — Using the remote control
28 - ENGLISH
Using the remote control
Inserting and removing the batteries
(i)
(ii)
Fig. 1
Fig. 2
1) Open the cover. (Fig. 1)
2)  
Insert the batteries and close the cover (insert the 
 m side first). (Fig. 2)
 fWhen removing the batteries, perform the steps in reverse order .
Setting the remote control ID numbers
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each projector individually using single...

Chapter 1 Preparation — Using the remote control
ENGLISH - 29
Connecting to the projector with a cable
When you use the system with multiple projectors, use commercial M3 stereo mini jack cables and connect the other devices to the / terminals of the projector body.
The remote control is effective even in places where an obstacle stands in the light path or where devices are susceptible to outside light.
Connecting terminalsConnecting to a second projector
M3 stereo mini jack cable (commercially...

30 - ENGLISH
Chapter 2 Getting Started
This chapter describes things you need to do before using the projector \
such as the setup and connections.